Fujitsu SMARTCASE S500 Manual de usuario

Assembly Instructions SMARTCASE S500

__________________________________________________________________________________________________________________________________________________________

Page 1 of 18 www.fujitsu.com

Assembly Instructions

SMARTCASE S500 & D3544-Sx

________________________________________________________________________________________________________

Assembly Instructions SMARTCASE S500

__________________________________________________________________________________________________________________________________________________________

Page 2 of 18 www.fujitsu.com

Table of Contents

Step 1 Preparing the Chassis .........................................................................................................................................3

Step 2 Installing the Heatsink .......................................................................................................................................4

Step 3 Inserting additional Modules (Memory / M.2 / …)...............................................................................................7

Step 4 Mainboard Assembly ........................................................................................................................................10

Step 5 Optional Components.......................................................................................................................................12

Installing WLAN Antennas......................................................................................................................................12

Speaker Assembly ...................................................................................................................................................13

Installing USB Type C Extension Cable...................................................................................................................14

Step 6 Closing the Chassis ...........................................................................................................................................15

Step 7 Adding Stands...................................................................................................................................................17

Assembly Instructions SMARTCASE S500

__________________________________________________________________________________________________________________________________________________________

Page 3 of 18 www.fujitsu.com

Step 1 Preparing the Chassis

Open the chassis with two hands by putting some pressure on your thumbs to push the cover reverse.

Remove top cover and unpack the accessories.

(Chassis kit content)

Rear Cover

Remove protective foil of

heat spreader pad!

Assembly Instructions SMARTCASE S500

__________________________________________________________________________________________________________________________________________________________

Page 4 of 18 www.fujitsu.com

Step 2 Installing the Heatsink

Fujitsu provides both a passive and an active heatsink solution, and a common mounting backplate.

Before assembling the mainboard into the chassis, it is recommended to install the optional onboard components

like cooler, RAM, M.2, etc.).

Mounting Backplate

Do not remove the insulating

foil of the backplate, otherwise

the mainboard may be

damaged due to possible short

circuit

(backplate position)

Note: Mounting holes

are asymmetrical!

Assembly Instructions SMARTCASE S500

__________________________________________________________________________________________________________________________________________________________

Page 5 of 18 www.fujitsu.com

Note:

Recommended mounting torque

for heatsink screws: 0.6Nm

(max. 0.8Nm)

Passive Heatsink

Note: The assembly solution with the coloured plastic part as shown above will be replaced

by an alternative “SoC die-crack-protection” implementation in future.

Hold the heatsink with one hand so

that it doesn’t tilt while installing the

screws

Assemble all 4 screws according to the

order shown. Each screw can be

tightened immediately!

Finally, remove the coloured plastic

part by turning it carefully clockwise.

This coloured plastic part is used for

secure assembly of the heatsink in

order not to damage the CPU die (“die

crack protection”).

After assembly, this part can be

scrapped

Note:

Recommended mounting torque for heatsink

screws: 0.6Nm (max. 0.8Nm)

Passive heatsink positioning:

Gaps of the passive heatsink must be located

towards the border of the mainboard

Mounting Backplate:

Do not remove the insulating foil of the

backplate, otherwise the mainboard may be

damaged due to possible short circuit

Assembly Instructions SMARTCASE S500

__________________________________________________________________________________________________________________________________________________________

Page 6 of 18 www.fujitsu.com

Active Heatsink

Note: The assembly solution with the coloured plastic part as shown above will be replaced

by an alternative “SoC die-crack-protection” implementation in future.

Note:

Recommended mounting torque for heatsink

screws: 0.6Nm (max. 0.8Nm)

Active heatsink positioning:

Heatsink must be positioned according to

picture

Mounting Backplate:

Do not remove the insulating foil of the

backplate, otherwise the mainboard may be

damaged due to possible short circuit

Hold the heatsink with one hand so

that it doesn’t tilt while installing the

screws

Assemble all 4 screws according to the

order shown. Each screw can be

tightened immediately!

Finally, remove the coloured plastic

part by turning it carefully clockwise.

This coloured plastic part is used for

secure assembly of the heatsink in

order not to damage the CPU die (“die

crack protection”).

After assembly, this part can be

scrapped

Assembly Instructions SMARTCASE S500

__________________________________________________________________________________________________________________________________________________________

Page 7 of 18 www.fujitsu.com

Step 3 Inserting additional Modules (Memory / M.2 / …)

The following picture shows some possible M.2 modules

Attention: Do not touch any pins! Touch the memory at the outside edges only.

Do not stick a barcode onto any modules!

The following procedure is recommended in order to ensure secure electrical contact:

Insert the memory angular and

pay attention to the notch!

Remove the memory again

completely from the DIMM

socket!

Insert memory again

Press down the memory until it

clicks into place

Do not press in the middle of the

memory, but press down on the

outside edges

Mainboard

M.2 2242

SSD/ Storage

M.2 SSD / Storage

2280

M.2 2230

WLAN

Memory

Assembly Instructions SMARTCASE S500

__________________________________________________________________________________________________________________________________________________________

Page 8 of 18 www.fujitsu.com

WLAN module / M.2. module assembly

First remove the M.2 mounting screws.

Insert M.2 module angular into the socket (while paying attention to the coding / notch).

Both modules, as shown in the picture, have to be touched on the outside edges only.

For the M.2 SSD (left socket), the assembly nut and screw are pre-installed for a 2240mm module.

In order to install a 2260 module, the 2240 assembly nut has to be moved to the 2260 position first.

For a 2280 module, the 2240 assembly nut has to be removed, and the pre-installed M.2 WLAN (2230) nut

is used for both M.2 2230 WLAN and M.2 2280 SSD

Recommended torque for the M.2 screw is 0.2Nm, and 0.3Nm for the nut.

Pay attention

to the notch

2240 screw /

nut position

Common 2280/2230

screw / nut position

2260 screw /

nut position

Assembly Instructions SMARTCASE S500

__________________________________________________________________________________________________________________________________________________________

Page 9 of 18 www.fujitsu.com

Sample installation M.2 2280 SSD module and M.2 2230 M.2 WLAN module:

Both modules are fixed by one common screw.

Assembly Instructions SMARTCASE S500

__________________________________________________________________________________________________________________________________________________________

Page 10 of 18 www.fujitsu.com

Step 4 Mainboard Assembly

1. Swing in the mainboard (rear chassis side)

2. Move it carefully to the final position

Take care for the heat spreader pad! Protective foil must be removed first!

Insert the chassis rear cover as shown above.

Push down the mainboard carefully while the four mounting holes fit onto the chassis nuts.

Otros manuales para SMARTCASE S500

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de De oficina de Fujitsu

Fujitsu

Fujitsu DESKPOWER 5000 Series Manual de usuario

Fujitsu

Fujitsu ESPRIMO C7xx Manual de usuario

Fujitsu

Fujitsu ESPRIMO P2560 Manual de usuario

Fujitsu

Fujitsu DESKPOWER P300 Series Manual de usuario

Fujitsu

Fujitsu ESPRIMO D53 Series Manual de usuario

Fujitsu

Fujitsu ESPRIMO P Manual de usuario

Fujitsu

Fujitsu ESPRIMO Q5030 Manual de usuario

Fujitsu

Fujitsu ESPRIMO D55 Series Manual de usuario

Fujitsu

Fujitsu SCENIC 800 Manual de usuario

Fujitsu

Fujitsu Siemens SCENIC 600 Manual de usuario

Fujitsu

Fujitsu FPC5D201DZ Manual de usuario

Fujitsu

Fujitsu ESPRIMO E3200 Manual de usuario

Fujitsu

Fujitsu ESPRIMO E420 E85+ Manual de usuario

Fujitsu

Fujitsu CELSIUS M720 Manual de usuario

Fujitsu

Fujitsu ESPRIMO E4xx Manual de usuario

Fujitsu

Fujitsu CELSIUS W520 Manual de usuario

Fujitsu

Fujitsu CELSIUS M720 Manual de usuario

Fujitsu

Fujitsu CELSIUS W5012 Manual de usuario

Fujitsu

Fujitsu SCENIC6511 Manual de usuario

Fujitsu

Fujitsu DESKPOWER 6000 Series Manual de usuario

Fujitsu

Fujitsu Esprimo P2 Series Manual de usuario

Fujitsu

Fujitsu CELSIUS W530 Manual de usuario

Fujitsu

Fujitsu CELSIUS J550 Manual de usuario

Fujitsu

Fujitsu ESPRIMO D5 Series Manual de usuario

Manuales populares de De oficina de otras marcas

HP m9060n - Pavilion - Elite Hoja de especificaciones

Asus

Asus E210 Series Manual de usuario

Dell

Dell Inspiron 600m Manual de usuario

Dell

Dell Inspiron 3662 Manual de usuario

TotalFlow

TotalFlow uFLO Manual de usuario

HP Presario SV7000 - Desktop PC Manual de usuario

HP ProDesk 400 G5 Manual

Logitech

Logitech MK320 Manual de usuario

Dell

Dell XPS 730 H2C Manual de usuario

Sony

Sony Vaio Series Manual de usuario

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manual de usuario

Alto

Alto MD 250 Manual de usuario

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series Manual de usuario

Sony

Sony VAIO VGX-TP1 Series Manual de usuario

Asus

Asus Eee Box B204 Manual de usuario

Dell

Dell Optiplex 9010 All In One Manual de usuario