Fujikura FSR-02 Instrucciones de montaje

Widget Associates

Fujikura FSR-02 Recoater Basic Operation Manual

Page 1 of 4

Fujikura FSR-02 Recoater Basic Operation Manual

1. PURPOSE

The purpose of this instruction manual is to provide basic instructions on the common functions of the FSR-02

recoater. The FSR-02 is used to recoat and proof test optical fiber splices.

2. SCOPE

This instruction manual applies to all work stations and operators involved with optical fiber splicing at Widget

Associates.

3. OPERATING THE FSR-02 RECOATER

Step

Task

Illustration

Notes

Press and hold the ON/OFF

button to turn on the

recoater.

The resetting function

takes a few moments to

complete.

Allow the recoater to warm

up.

The mold must be closed

for the warm up function

to proceed.

Widget Associates

Fujikura FSR-02 Recoater Basic Operation Manual

Page 2 of 4

Open the fiber clamps and

mold.

The protective tissues

must be removed from

the opened clamps

before laying fiber into

the recoater.

Hold the spliced fiber taut

and lay the fiber across the

recoater from left to right.

Make sure the fiber is

centered in the foam

guides at the outer ends

of each clamp and is

aligned with the V-

grooves at each side of

the mold.

Close the left fiber clamp.

The fiber clamp slides

from left to right. Keep

enough tension in the

fiber to prevent the fiber

from jumping out of the

V-grooves.

Gently pull the fiber to the

right to slide the left-side

fiber clamp to its rightmost

position.

Take note of the position

of the left fiber clamp in

Step 5 versus Step 6.

Widget Associates

Fujikura FSR-02 Recoater Basic Operation Manual

Page 3 of 4

Close the right fiber clamp

and the mold

The recoater will display

a READY message when

functioning properly.

Press the SET button to

begin recoating the fiber.

The screen will display an

INJECTION message and

then a UV

COMPENSATIVE message

while recoating.

Open the mold when the

FINISH message is displayed.

Press the SET button once

more to start the proof test.

Do not touch the

recoater while it is

performing the proof

test.

Widget Associates

Fujikura FSR-02 Recoater Basic Operation Manual

Page 4 of 4

When the proof test is

complete, open the right

fiber clamp first, and then

open the left fiber clamp.

Carefully remove the fiber

by lifting the fiber up from

the right side first.

Keep the fiber taut and

straight when removing

it from the recoater.

Use Isopropyl Alcohol and

Kimwipes to thoroughly

clean the surface of the

mold.

Replace the protective

tissues under each fiber

clamp and the mold.

Press and hold the ON/OFF

button to shut down the

recoater.

The ON/OFF button must

be held until the SHUT

DOWN message appears.

Otros manuales de Sistema de soldadura de Fujikura

Fujikura

Fujikura 90S Manual de usuario

Fujikura

Fujikura 62S Manual de usuario

Fujikura

Fujikura QRG-02 Manual de usuario

Fujikura

Fujikura FSM-60S Manual de usuario

Fujikura

Fujikura 70S Manual de usuario

Fujikura

Fujikura CB-08 Manual de usuario

Fujikura

Fujikura 19S+ Manual de usuario

Fujikura

Fujikura KSP75-FP-005468 Manual de usuario

Fujikura

Fujikura FSM-40S Manual de usuario

Fujikura

Fujikura 90S Manual de usuario

Fujikura

Fujikura FSM-50S Manual de usuario

Manuales populares de Sistema de soldadura de otras marcas

Berner

Berner PLASMACUT 54 Manual de usuario

Pro Spot

Pro Spot PR-155 Manual de usuario

Forney

Forney 210 Manual de usuario

Thermal Arc

Thermal Arc 400S Manual de usuario

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manual de usuario

GYS

GYS PROTIG 201 AC/DC Manual de usuario

TAFA

TAFA 30*8B35 Manual de usuario

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manual de usuario

ESAB

ESAB Buddy Arc 145 Manual de usuario

CIGWELD

CIGWELD 636804 Guía rápida

Red-D-Arc

Red-D-Arc DC-400 Manual de usuario

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario

Elettro

Elettro HI-MIG 3000 SYNERGIC Manual de usuario

WIA

WIA Weldmatic 270 CP132-2 Manual de usuario

Sonics

Sonics H520T Manual de usuario

Miller

Miller Big Blue 400D Manual de usuario

NewArc

NewArc RT2000 Guía de inicio rápido

Hypertherm

Hypertherm powermax1000 Manual de usuario