Fromm TP-601D1 Guía

Explanations for Each Model NO. :

TP-601D1 : Standard Single Phase Model

TP-601D3 : Standard Three Phase Model

TP-601L1 : Low Table Single Phase Model

TP-601L3 : Low Table Three Phase Model

01/10/08

PART I

CONTENTS

1. Safety Instructions …………………………………

…

1~2

2. Construction and Function of Units ……………….. 3~4

3. Technical Data ……………………………………… 5~6

4. Control Panel ………………………………………

…

5. Electric Control Unit ………………………………

…

6. How to Load P.P. Strap ……………………………

…

9~10

7. How to Operate ……………………………………… 11

8. Recommend for Trouble-free Operation ……………

…

9. Adjustments ………………………………………… 12~17

10. Installation of Arch Unit ……………………………

…

18~19

11. Wiring Diagram ……………………………………

…

20~25

12. Troubleshooting ……………………………………

…

01/10/08

(1) Before operating

a. Please always wear proper eye protection and safety gloves before operating this

Eye protection must be worn Safety gloves must be worn

b. Please make sure if the power voltage is correct.

c. It can only be operated with P.P. strap; not PET strap or Polyester cord strap.

(2) During operating

a. The weight of package should not exceed 100kg, and the size should not be

less than 130mm (width) x 20mm (high).

b. Check if the machine emits any smokes or unusual sound when it is running.

(3) After operating

a. Please pull out the power plug.

b. Please get rid of the dirt or impurity on the machine.

(4) Signs

Caution, risk of electric shock Do not touch!

Heiss!Hot! chaud!

c. Warning

c-1 For your own safety, please read instruction manual before operating. Keep

away from arch while the machine is running.

c-2 Do not put your hands or body into the Archworking area when the machine is

machine.

running.

-1-

1. Safety Instructions

01/10/08

a. Please turn off the power before opening the top plate.

b. Please do not touch the heater due to the high temperature.

c. Be careful with the heater if you open the upper top plate.

(6) Maintenance

(7) Other remainders

a. Do not alter or bypass protective interlocks

b. The operation manual must remain attached to the machine at all times

c. Do not alter circuits and machine unless authorized to do so by the manufacturer.

d. All electrical apparatus must be properly grounded.

e. Wire the machine according to the local electrical code.

-2-

When the machine arrives in your warehouse, you need to use a forklift to

take it off from the pallet. If you could go down to the bottom side of

the machine, you would see an indication sticker as follows: (TP-601L)

position. After making few distance adjusting, you then could drive the

Follow this sticker and lead the teeth of a forklift to that indicated

teeth in and take off the machine.

(5) Attention

01/10/08

1 Strapping head unit

2 Bandway unit

5 Body frame unit

6 Electric control unit

8 Auto strap feeding unit 3 Accumulator unit

This unit is the most important part of the

machine for cutting and sealing of P.P.

strap.

This is the arch track through which

P.P. strap forwards or reverses.

This unit accumulates the quantity of strap required

for smooth feeding into the chute track.

Holds the strap coil.

(If strap core is

280mm, you can take

off the center drum to

4 Reel unit

have core size 200mm.)

-3-

2. Construction and Function of Units

a. (TP-601D)

01/10/08

-4-

b. (TP-601L)

through which P.P. strap

2 Bandway unit

This is the arch track

forwards or reverses.

arch track.

3 Pool unit

This unit pools strap

adeqately for its

smooth feeding in

4 Reel unit

(If strap core is 280mm,

you can take off the center

drum to have core size 200mm.)

Holds the strap coil.

machine for cutting and sealing of P.P.

This unit is the most important part of the

1 Strapping head unit

strap.

5 Body frame unit

6 Electric control unit

8 Auto strap feeding unit

01/10/08

-5-

3. Technical Data

a. TP-601D

Sealing method Heat

Strap width:

Strap thickness:

Strap reel diameter:

Width :

Depth:

Table height:

Electrical connection:

8 mm to 12 mm (3/8" - 1/2")

0.55 mm up to 0.75 mm (0.022" - 0.03")

200 mm (8" nominal)

1430 mm (56.3")

620 mm (24.4")

810 mm (31.9")

AC 110V/220V/230V/240V (50/60Hz), 1PH

AC 220V/380V/400V (50/60Hz), 3PH

220 kg (341.7 lbs.)Weight: 83 dB (A)Noise emission: 5°C ~ 40°C (41°F ~ 104°F)Ambient temp:

01/10/08

-6-

b. TP-601L

Sealing method Heat

Strap width:

Strap thickness:

Strap reel diameter:

Width :

Depth:

Table height:

Electrical connection:

8 mm to 12 mm (3/8" - 1/2")

0.55 mm up to 0.75 mm (0.022" - 0.03")

200 mm (8" nominal)

1880 mm (74")

620 mm (24.4")

410 mm (16.1")

AC 110V/220V/230V/240V (50/60Hz), 1PH

AC 220V/380V/400V (50/60Hz), 3PH

235 kg (518.1 lbs.)Weight:

Noise emission:

Ambient temp: 83 dB (A)

5°C ~ 40°C (41°F ~ 104°F)

01/10/08

RESET

TP-601D

1 Start Switch

2 Reset switch

3 selector switch

4 Tension Adjustment Knob

-7-

4. Control Panel

This is the switch to start a strapping operation.

A strapping cycle is completed only after actuation of

this switch.

This is the switch to activate auto strap feeding.

In addition, it is used for troubleshooting. If the strap is

mis-fed, you can push this button to solve the problem.

While selector switch is placed to the position , the

machine will automatically strap the package when it

isplaced on the table and passes the chute arch, if the

package remains under the arch, the strapping cycle

will continue. While the selector switch is placed to the

position , after positioning the package under the

arch, push the "START" switch, then one strap will be

applied.

External adjustment of strap tension by step-by-step

rotation of this knob.

RESET

TP-601L

01/10/08

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Equipos de embalaje de otras marcas

U-Line

U-Line S-15188 Manual de usuario

ITATOOLS

ITATOOLS ITA22 Manual de usuario

Fieldpiece

Fieldpiece MG44 Manual de usuario

Smart wasp

Smart wasp X300 Manual de usuario

U-Line

U-Line S-1135 Manual de usuario

Z.R. Tools

Z.R. Tools MS25-1 Manual de usuario

Sipromac

Sipromac SIPROVAC 620A Manual de usuario

strapex

strapex STR 66 Manual de usuario

U-Line

U-Line H-5334 Manual de usuario

Imetec

Imetec Q5901 Manual de usuario

Transpak

Transpak TP-201 Guía

Lacor

Lacor 69352 Hoja de especificaciones

Eastey

Eastey EXS-100 Manual de usuario

Inova

Inova SV 125 Manual de usuario

CombiSteel

CombiSteel 7529.0010 Manual de usuario

HUALIAN

HUALIAN HVC-260T/1A Manual de usuario

U-Line

U-Line H-2079 Manual de usuario

Strapack

Strapack iQ400 Instrucciones de operación