Fritsch PULVERISETTE 15 Manual de usuario

Assembly instructions

UNIVERSAL SUPPORT STAND

PULVERISETTE 15, 16, 19, 25 and high-performance cyclone

separator

Read the instrucons prior to performing any task!

Version 06/2017 Index 000 - 45.5820.00 - 45.5824.00/45.5825.00

Fritsch GmbH

Milling and Sizing

Industriestr. 8

D - 55743 Idar-Oberstein

Telephone: +49 (0)6784/ 70-0

Fax: +49 (0)6784/ 70-11

Email: inf[email protected]

Internet: www.fritsch.de

Cercaons and CE conformity

Fritsch GmbH has been cered by the TÜV-Zerzierungsgemeinscha

e.V.

An audit cered that Fritsch GmbH conforms to the requirements of the

DIN EN ISO 9001:2008.

The enclosed Conformity Declaraon lists the guidelines the FRITSCH

instrument conforms to, to be able to bear the CE mark.

Cercaon

CE Conformity

Cercaons and CE conformity

- 3 -

Table of contents

1Assembly of stand.......................................................................... 5

2 Fastening points............................................................................. 6

3Aaching devices........................................................................... 7

3.1 Assembly of PULVERISETTE 15............................................... 7

3.2 Assembly PULVERISETTE 16 (as of year of manufacture

2016)...................................................................................... 8

3.3 Assembly of PULVERISETTE 19............................................... 9

3.4 Assembly of PULVERISETTE 25............................................. 10

3.5 Assembly of high-performance cyclone separator.............. 11

Table of contents

- 4 -

1 Assembly of stand

1Mounng plate

2 3 x cross braces

3 4 x stand legs

4 6 x clamping rings + 12 x washers + 6 x M6 nuts + 6 x

M6x25 cylinder screws

5 4 x protecve caps

To assemble the universal support stand, proceed as follows:

1. Lay the mount plate on a at surface.

2. Slide 2 clamping rings over 2 of the 4 stand legs.

3. Slide the remaining 2 clamping rings on the two other stand legs.

4. Screw the 4 stand legs into the mounng plate so that the ones

with the 2 clamping rings on the side of the smaller secon of the

mounng plate are fastened.

5. The 3 lower clamping rings should be fastened at a distance of

10cm to the oor.

6. Fit the 3 cross braces as shown in the image and screw to the

clamping rings.

A cross brace must be mounted on the back of the

tripod. What is the rear side depends on the device to

be mounted.

Assembly of stand

- 5 -

2 Fastening points

Drilling plan for using dierent devices and combinaons:

1 PULVERISETTE 16, old version (up to year of manufac-

ture 2015)

2 High-performance cyclone separator (assembly on

the le side for use with P19; on the right side for use

with P19/P25)

3 PULVERISETTE 15

4 PULVERISETTE 25

5 PULVERISETTE 19

6 PULVERISETTE 16 (as of year of manufacture 2016)

Fastening points

- 6 -

3 Aaching devices

3.1 Assembly of PULVERISETTE 15

1. Have 2 persons li the mill on to the universal stand and posion it

over the drilled holes displayed. The drilled holes marked in yellow

are suitable for PULVERISETTE 15 with larger motor.

CAUTION!

Secure the device against pping over unl it is

fastened completely. Due to its centre of gravity,

the mill will lt forwards.

2. Fasten the mill using the assembly set provided. The screws are

inserted from above with a washer and are locked from below with

a washer and a nut.

Aaching devices

- 7 -

3.2 Assembly PULVERISETTE 16 (as of year of manufacture 2016)

1. Posion the mill on the corresponding drilled holes. (see chapter

1.1)

2. Insert the enclosed metal plates into the U secons below the

PULVERISETTE 16.

3. Fasten the mill from below by screwing it through through the

holes in the mounng plate of the universal stand, through the U

secon of the PULVERISETTE 16 and, for locking, through the metal

plates inserted in the U secons.

Aaching devices

- 8 -

3.3 Assembly of PULVERISETTE 19

1. Have 2 persons li the mill on to the universal stand and posion it

over the drilled holes displayed.

CAUTION!

Secure the device against pping over unl it is

fastened completely. Due to its centre of gravity,

the mill will lt forwards.

2. Fasten the mill from below using the assembly set provided.

Aaching devices

- 9 -

3.4 Assembly of PULVERISETTE 25

1. Have 2 persons li the mill on to the universal stand and posion it

over the drilled holes displayed.

CAUTION!

Secure the device against pping over unl it is

fastened completely. Due to its centre of gravity,

the mill will lt forwards.

2. Fasten the mill from below using the assembly set provided.

Aaching devices

- 10 -

Otros manuales para PULVERISETTE 15

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Equipo de laboratorio de Fritsch

Fritsch

Fritsch ANALYSETTE 28 IMAGESIZER Manual de usuario

Fritsch

Fritsch pulverisette 14 Manual de usuario

Fritsch

Fritsch PULVERISETTE 13 premium line Manual de usuario

Fritsch

Fritsch ANALYSETTE 3 Manual de usuario

Fritsch

Fritsch PULVERISETTE 7 classic line Manual de usuario

Fritsch

Fritsch PULVERISETTE 1 premium Series Manual de usuario

Fritsch

Fritsch ANALYSETTE 18 Manual de usuario

Fritsch

Fritsch PULVERISETTE 5 Manual de usuario

Fritsch

Fritsch LABORETTE 27 Manual de usuario

Fritsch

Fritsch PULVERISETTE 11 Manual de usuario

Fritsch

Fritsch PULVERISETTE 0 Manual de usuario

Fritsch

Fritsch analysette 22 ECONOMY Manual de usuario

Fritsch

Fritsch ANALYSETTE 22 NeXT Manual de usuario

Fritsch

Fritsch PULVERISETTE 6 Classic Manual de usuario

Fritsch

Fritsch premium PULVERISETTE 14 Manual de usuario

Fritsch

Fritsch PULVERISETTE 7 classic line Manual de usuario

Fritsch

Fritsch ANALYSETTE 28 IMAGESIZER Manual de usuario

Fritsch

Fritsch PULVERISETTE 7 premium line Manual de usuario

Fritsch

Fritsch PULVERISETTE 19 Manual de usuario

Fritsch

Fritsch PULVERISETTE 29 Manual de usuario

Fritsch

Fritsch PULVERISETTE 7 Manual de usuario

Fritsch

Fritsch PULVERISETTE 7 premium line Manual de usuario

Fritsch

Fritsch PULVERISETTE 1 classic line Manual de usuario

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario