Frigidaire FFTW1001PW0 Manual de usuario

TABLE OF CONTENTS

Important Safety Instructions .......................... 2-3 AccessorEes ..................................................... 10

Installatton Requirements ................................ 4-6 Fran_als ........................................................... 1I

Installatton Instructions ................................... 7-9 Espa_ol ........................................................... 21

Recognize safety syrnboisr words

and labels

Safety items throughout this manual are labeled with

a WARNING or CAUTION based on the risk type as

described below:

Definitions

This is the safety alert symbol. It is used to alert

you to potential personal injury hazards, Obey all safety

messages that follow this symbol to avoid possible injury

or death.

Shipping Hardware

CI Foam shipping restraint (inside wash tub)

removed and stored

1:3 Foam shipping support (underneath tub inside

cabinet) removed and stored

Leveling

1:3 Washer is level, side-to-side and front-to-back

[:3 Cabinet is setting solid on all corners

Water Supply

1:3 Use only new hoses and verify rubber sealing

washers are installed

{:3 HOT supply is connected to HOT inlet and

COLD supply is connected to COLD inlet

{:3 HOT and COLD water supply turned on

[:3 No leaks present at water supply connections

or appliance inlet connections -

recheck in 24 hours

DANGER indicates an imminently hazardous situation Drain

which, if not avoided, will result in death or serious {:3 Stand pipe or wall drain height minimum 36"

injury.

CAUTION indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate

[:3 Washer plugged in

Final Checks

[3 Installation Instructions and Use and Care

Guide read thoroughly

CI Water enters drum when cycle starts with lid

lowered.

C! Registration card sent in

IMPORTANT indicates installation, operation or

maintenance information which is important but not

hazard-related.

The electrical service to the washer must conform with

local codes and ordinances and the latest edition of the

National Electrical Code ANSI/NFPA 70 or in Canada

the Canadian Electrical Code C22.1 part 1.

ii!ii:ii!ii_i_i!!i_iii_ii_i_i_i_iii_ii_!_i!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!iii_i!i!i_i!i!i!!ii!i_!i_!i_!i_!i_!i_!i_!i_!i_!i_i_!i!_i!i_ii_ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!!!_iiiiiiiiiiiiiiii_ii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_i_i_i_ii_i,iii!!

For your safety the information in this manual must be

followed to minimize the risk of fire or explosion or to

prevent property damage, personal injury or loss of life,

Do not store or use gasoline or other flammable vapors

and liquids in the vicinity of this or any other appliance.

Destroy the carton and plastic bags after the washer is

unpacked. Children might use them for play. Cartons

covered with rugs, bedspreads, or plastic sheets can

become airtight chambers causing suffocation. Place

all materials in a garbage container or make materials

inaccessible to children. installing, operating and maintaining any appliance.

Maximum benefits and enjoyment are achieved

when all the Safety and Operating Instructions are

understood and practiced as a routine with your

laundering tasks.

Save these instructions for future reference,

Tools and materials needed for installation;

AND

Carpenter's level Inlet hose(x2)

Hoses are not included with washer purchase.

See "Accessories" section for various inlet

hose kits to fit your specific installation.

Bef° beg!nn!ng!ns!a!!at!on !! uni b a andre!! !oa !u suppo! ha bee [emoved: .....

Electrical system requirements Ground requirements

CIRCUIT - Individual, properly polarized and grounded

15 amp. branch circuit fused with 15 amp. time delay

fuse or circuit breaker.

POWER SUPPLY- 2 wire, with ground, 120 volt single

phase, 60 Hz, Alternating Current.

Because of potentially inconsistent voltage capabilities,

the use of this washer with power created by gas

powered generators, solar powered generators, wind

powered generators or any other generator other than

the local utility company is not recommended.

OUTLET RECEPTACLE- Properly grounded 3-prong

receptacle to be located so the power supply cord

is accessible when the washer is in an installed

position.

Groundin

watt Do not, under "_

any circumstances, J

CUt, remove_

or bypass the

grounding prong. J

with a licensedelectrician ifyou are in doubt as to

whether the appliance is properly grounded.

The washer MUST be grounded. In the event of

malfunction or breakdown, grounding will reduce the

risk of electrical shock by a path of least resistance

for electrical current.

Since your washer is equipped with a power supply

cord having an equipment-grounding conductor

and a grounding plug, the plug MUST be plugged

into an appropriate, copper wired receptacle that is

properly installed and grounded in accordance with

all local codes and ordinances or in the absence of

local codes, with the National Electrical Codes, ANSI/

NFPA70 (latest edition). If in doubt, call a licensed

electrician. DO NOT cut off or alter the grounding

prong on the power supply cord. In situations where

a two-slot receptacle is present, it is the owner's

responsibility to have a licensed electrician replace

it with a properly grounded three prong grounding

type receptacle.

Power cord with

3-prong grounded plug

Water supply requirements

Hot and cold water faucets MUSTbe 3/4 inch with

threading for laundry hose connection. Water pressure

MUST be between 30 and 120 psi. Pressure difference

between hot and cold cannot be more than 10 psi. Your

water department can advise you of your water pressure.

GFI (Ground Fault Interrupter) receptacle is not

required.

Drain system requirements

! Drain capable of eliminating i7 gals (64,3 L) per

minute.

2 A standpipe diameter of !-i/4 in. (3,i8 cm)

minimum,

3 The standpipe height above the floor should be:

Minimum height: 36 in. (91 cm)

Maximum height: 96 in. (244 cm)

Installation in a Recess or Closet

If washer and dryer are installed in the same closet, door

ventilation is required: A minimum of !20 square inches

(774.2 cm _) of opening, equally divided at the top and

bottom of the door, is required. Louvered openings should

be located 3 inches (7.6 cm) from bottom and top of

door. Air openings are required to be unobstructed when

a door is installed. A Iouvered door with equivalent air

openings for the full length of the door is acceptable.

96"

(244 cm)

max. I

36"

(91 cm)

rain.

For installations requiring a longer drain hose, have

a qualified technician install a longer drain hose

(according to your model number) available from an

authorized parts distributor. For drain systems in the

floor, install a syphon break kit available from your local

hardware store.

(7.6cm)

closet door

Clearance requirements

DO NOT INSTALL YOUR WASHER:

1 In an area exposed to dripping water or outside

weather conditions• The ambient temperature

should never be below 60° F (i5,6 ° C) to

maximize detergent effectiveness•

2 In an area (garage or garage-type building)

where gasoline or other flammables (including

automobiles) are kept or stored•

3 On carpet, Floor MUST be solid with a maximum

slope of 1 inch (2•5 cm). To minimize vibration

or movement, reinforcement of the floor may be

necessary,

MINIMUM INSTALLATION CLEARANCES - Inches (cm)

SIDES REAR TOP FRONT

0" 0" 20.5"

Alcove _ (0cm) L (0cm) _ (52cm) _ n/a

0" 0" 20.5" 1"

Closet (0 cm) (0 cm) (52 cm) (2.5 cm)

O" 0"

(0 cm) (0 cm)

]" O"

(2.5 crn) (0 crn)

215"

(52cm)

Washer Dimensions

power cord attachment

location on rear of unit1

drain hose

retainer on rear

of washer 2

water supply

connection on

rear of washer

42"

(107cm)

_28.75"(78 cm)_

1Power supply cord length approximately 60 inches (152.5 cm).

2Loose drain hose tength beyond hose retainer approximately 61 inches (155 cm),

Leveling your washer

Excessive noise and vibration can be prevented by

properly leveling the washer.

1With the washer within 4 feet (1 m) of its final

location, use a carpenter's level to level your

washer front-to-back and side-to-side. For front-to-

back leveling, place edge of the level flush to the

front panel. For side-to-side leveling place the edge

of the level flush to the side panel.

2 Use adjustable pliers to adjust the leveling legs so

the washer is level front-to-rear and side-to-side,

and stable corner-to-corner.

3Press down on alternate corners and sides and feel

for the slightest movement. Adjust the appropriate

leg(s) so the washer sits solidly on the floor on

ALL four legs. Keep the leveling leg extension at a

minimum for best performance of the washer.

lower

Connecting inlet water

1Run some water from the hot and cold faucets

to flush the water lines and remove particles

that might ctog the water valve screens and to

determine which faucet is hot and which is cold

supply.

RUBBER WASHERS USE ONLY

MUST BE PRESENT NEW HOSES

Hoses are not included with washer purchase. See

"Accessories" section for various inlet hose kits to fit

your specific installation,

2Connect the HOT inlet hose to the HOT inlet

connection on the washer and the COLD inlet

hose to the COLD inlet connection on the washer.

Tighten by hand until snug. Then tighten each

supply connection another 2/3 turn with pliers.

Do not cross thread or over=tighten these

connections.

3Connect the HOT inlet hose to the HOT water

supply and the COLD inlet hose to the COLD water

supply. Tighten by hand until snug. Then tighten

each supply connection another 2/3 turn with

pliers. Do not bendr kink or pinch water inlet

hoses.

4 Turn on the water and check for leaks.

///

C _ d SJ

eRED

(HOT)

BLUE

(COLD)

Connecting drain hose to washer

Inspect rubber flap on pump outlet. Ensure it is in

place and not folded under or torn.

1 With the spring clamp already installed, place

the drain hose elbow over the pump outlet at the

lower rear of the washer. Ensure the hose elbow is

completely and squarely seated to the pump outlet

before using pliers to move the spring clamp into

place.

DRAIN PUHP

OUTLET

SLIDE CLAHP

TO HERE

SPRING CLAHP

2 "Thread" the end of the drain hose up through

either of the outer, larger "D" ring retainers below

the top panel.

3 Locate the anti-siphon ring shipped with your

washer. Place it over the end of the drain hose and

slide it past the first ring of "accordion" ribs.

ANTI-SIPHON

"._ DISC

Connecting drain and electrical

IForm a "U" shape on the end of the drain hose

with the hose pointed toward the drain, Placethe

formed end in a laundry tub or a standpipe and

secure with a cable tie provided in the enclosure

package,

2Place the hook end of the drain hose inthe drain

opening, Secure the drain hose with the cable

tie (provided in the enclosure package) to the

standpipe, inlet hose, laundry tub, etc. so the hose

does not pull out from the force of the water.

The standpipe inside diameter must be 1-1/4" (3,2 cm)

minimum. There must be an air gap around the drain

hose in the standpipe, A snug hose fit can cause a

s!ph°n!ng acti°n: .........................................................................................................................

CABLE TIE

Check to ensure the power is off at a circuit breaker/

fuse box before plugging the power cord into an outlet,

3 Plug the power cord into a grounded outlet.

Power cord with

3--prong grounded plug

4Turn on the power at the circuit breaker/fuse box.

5Carefully slide the washer to its final position,

Recheck for level and rock corners for stability.

6 Read the Use &Care Guide provided with the

washer, It contains valuable and helpful information

that will save you time and money.

7 Run the washer through a complete cycle, checking

for water leaks and proper operation,

8If you have any questions during initial operation,

please review the "Avoid Service Checklist" in your

Use & Care Guide before calling for service,

9 Place these instructions in a location near the

appliance for future reference,

MOBILE HOME INSTALLATION KIT

P/N 137067200

Installation in a mobile home requires the use of a

MOBILE HOMEINSTALLATION KIT,

INLET HOSE KITS

Please call 866-233-8353 (in Canada, 800=265-8352)

to explore hose kit options that will meet your specific

installation needs.

UNIVERSAL APPLIANCE WRENCH

P/N 137019200

A UNIVERSAL APPLIANCE WRENCH is available to aid in

dryer/washer feet adjustment.

TOUCH UP PAINT PENS*

Classic White Touch Up Pen - P/N 5304468812

*Other colors may be available. Contact the source where you

purchased your washer.

Failure to use accessories manufactured by (or approved

by) the manufacturer could result in personal injury,

Technical Sheet/Wiring Diagram:

A wiring diagram and technica! data sheet are located

inside the washer console.

To remove the console faceplate follow the directions

below:

I. Disconnect washer from electrical source.

2. Remove four screws on back of the console housing.

3. Slowly rotate console forward on hinge tabs.

Internal parts of console are attached with wires to the

washer. Prevent machine damage. Do NOT pull console

away from washer.

4. When finished with repair, return sheet inside console

and ensure hinge tabs are inserted in top panel.

Gently rotate console back and reinsert all four screws.

_ CONSOLESCREWS

HINGETABS

Replacement parts:

If replacements parts are needed for your washer, contact

the source where you purchased your washer or refer to

your Use and Care Guide for more information.

controls. Wiring errors can cause improper and dangerous

operation. Verify proper operation after servicing,

i!!i!i!l!_!0 ill

Otros manuales para FFTW1001PW0

Tabla de contenidos

Idiomas:

Otros manuales de Arandela de Frigidaire

Frigidaire

Frigidaire GLWS1979AS3 Manual de usuario

Frigidaire

Frigidaire FAFW3574KB - Affinity Tumble Action Washer Manual de usuario

Frigidaire

Frigidaire GLTF1240AS0 Manual de usuario

Frigidaire

Frigidaire FWS933FS3 Manual de usuario

Frigidaire

Frigidaire FLBY12GGAWFD Manual de usuario

Frigidaire

Frigidaire ATF6000ES0 Manual de usuario

Frigidaire

Frigidaire ATF705X Manual de usuario

Frigidaire

Frigidaire Affinity FAHE4044M W? Manual del propietario

Frigidaire

Frigidaire FTW3014KW - 3.0 cu. Ft. Washer Guía de inicio rápido

Frigidaire

Frigidaire FRFW3700L W Manual de usuario

Frigidaire

Frigidaire FFFW5000QW0 Manual del propietario

Frigidaire

Frigidaire Affinity FAFW3511K B Manual de usuario

Frigidaire

Frigidaire MWX233RB Manual de usuario

Frigidaire

Frigidaire FTF2140ES3 Manual de usuario

Frigidaire

Frigidaire FLSE72RB Manual de usuario

Frigidaire

Frigidaire WL Manual de usuario

Frigidaire

Frigidaire FTF630AS0 Manual de usuario

Frigidaire

Frigidaire Gallery GLTF1040A Manual de usuario

Frigidaire

Frigidaire CTF140ES0 Manual

Frigidaire

Frigidaire FFFW5100PW Manual de usuario

Frigidaire

Frigidaire FTFB4000FS0 Manual de instrucciones

Frigidaire

Frigidaire ATFB6000E Manual de usuario

Frigidaire

Frigidaire 1341085500 Manual de usuario

Frigidaire

Frigidaire GLTF1570E Manual de usuario

Manuales populares de Arandela de otras marcas

Tricity Bendix

Tricity Bendix AW 1000 W Guía del producto

Panasonic

Panasonic NA-F60L5WRB Manual de usuario

GE WSLP1500 Manual

Electrolux

Electrolux EWF1284EDW Manual de usuario

Bosch

Bosch WAN2829BSN Manual de usuario

LG TV2516DV3B Manual de usuario

LG TH2517DSAV Manual de usuario

VESTEL

VESTEL CMH-XL 7510 TE Manual de usuario

AEG

AEG 74335 Manual de operación

Johnson

Johnson JWF721A Manual de usuario

Beko

Beko WTE7604XLW0 Manual de usuario

Danby

Danby DTT100A1WDB Instrucciones de montaje

Amica

Amica WA 14 Ex Manual de usuario

Daewoo

Daewoo DWD-F1222 Manual de usuario

Bosch

Bosch WAS28461AU Manual de usuario

Miele

Miele PW 6080 Vario Manual de usuario

Finlux

Finlux FLX108CF220 Manual de usuario

Whirlpool

Whirlpool 3LBR5132AN0 Manual de usuario