Frigidaire FAL125M1A1 Manual de usuario

Installation Instructions

For A-Kit 22"

Please read ALL instructions before installing. Two

people are recommended to install this product. If

a new electrical outlet is required, have the outlet

installed by a qualified electrician before installing

unit. See #5 in Preliminary Instructions following.

Preliminary Instructions

Do the following before starting to install unit.

See illustrations below.

1. Check window opening size - the mounting

parts furnished with this air conditioner are

made to install in a wooden sill double-hung

window.The standard parts are for a window

opening of 30" (711 mm) minimum to 42"

(1067 mm) maximum width. Open sash to a

minimum of 19" (483 mm). (FIG. 1)

2. Check condition of window - all wood parts

of window must be in good shape and able to

firmly hold the needed screws. If not, make

repairs before installing unit.

3. Check your storm windows - you will need

1/2" (13 mm) clearance below window stool.

If storm window frame does not allow the

clearance required, correct by adding a piece

of wood as shown in FIG. 2, or by removing

storm window while room air conditioner is

being installed. (continued)

FIG. I _SASH

19" MIN,

1/2",_MIN. 1

STORMWINDOWFRAME

OROTHEROBSTRUCTION

FIG. 2

SASH

19" MIN.

1/2" MIN. ',1 1/2" MIN,[

THIO NESSAS

[L_ _ REQUIRED,ALONG

I v ENTIRE STOOL.

STORM WINDOW FRAME FASTENWITH TWO

OR OTHER OBSTRUCTION NAILS OR SCREWS.

1 309000915 (0111)

4. CHECK FOR ANYTHING THAT COULD

BLOCK AIRFLOW - check area outside

of window for things such as shrubs,

trees, or awnings. Inside, be sure

furniture, drapes, or blinds will not

stop proper airflow.

5. Check the available electrical service -

power supply must be the same as that

shown on the unit serial nameplate. (See

Owner's Guide for serial plate location.)

Power cord is 48" long. Be sure you have an

outlet near. It is best to not use extension

cords!

All models have a 3-prong service plug to

provide proper service and safe positive

grounding. Do not change plug in any way.

Do not use an adapter plug. If your present

wall outlet does not match your plug, call a

qualified electrician to make the needed

change.

Avoid fire hazard or

electric shock. Do not use an extension

cord or an adapter plug. Do not remove

any prong from the power cord.

Grouding type

wall receptacle

under

6. Carefully unpack air conditioner - remove

all packing material. Protect floor or carpet

from damage.Two people should be used to

move and install unit.

Tools Required

t/ a large flat blade screwdriver

t/ #2 Phillips screwdriver

t/ tape measure

t/ pliers

t/ sharp utility knife

t/ pencil

Hardware (in plastic bag)

Frame to Sash

3/4" Long Hex-

Head Screw

Safety Lock

Speed Nuts

Screws Top

Angle, Side

Retainer

Screw Front

Retaining

Qt¢

Window Mounting

Remove Chassis

1. To slide chassis from cabinet, hold cabinet

with left hand, while pulling on strap provided

at the front of the unit.

2. Do not remove formed foam at the front of

the unit.

Assemble Window

Filler Panels

1. Place cabinet on floor, a bench, or a table.

2. Slide "I" section of window filler panel into

side retainer on the side of the cabinet (see

Figures 3-4). Do both sides.

STRAP NOTE: Do not use strap for lifting unit. It

is for sliding chassis WITHIN cabinet only (to aid

in cleaning, maintenance, etc.). Be CAREFUL of

sharp edges on coil fins.

Install Top Angle

and Side Retainers

1. Attach foam gasket to _lbp Rail and Side

Retainers as shown in FIG. 1.

2. Install Top Rail Support Brace, and Side

Retainers to cabinet as shown using screws

and (4) speed nuts to secure

3. Insert top and bottom legs of window filler

panel frame into the channel of the Top Rail

and Bottom Rail. Repeat on other side.

(continued)

Place Cabinet in

Open window. Mark

center of window stool.

Install Window Lock

Sash Seal

1. Trim sash seal to fit window width. Insert

into space between upper and lower sashes.

2. Place cabinet in window with bottom stool

angle firmly seated over window stool as

shown. Bring window down behind top angle

to hold cabinet in place.

STOOL

ANGLE

2. Holding the sash down behind the back of

the Ibp Rail (as shown) attach the safety lock.

(You may wish to pre-drill a pilot hole using a

1/8" diameter drill.)

3. Shift cabinet left or right as needed to line up

center of cabinet on center line marked on

stool.

4. Fasten cabinet to window stool with 2 screws

into holes. (You may wish to pre-drill pilot hole

using 1/8" diameter drill.)

5. Add bottom rail seal over screws to window

stool.

3/4" LONG HEX-

HEAD SCREW

Extend Window

Panels

Extend panels to fill window opening

completely: Install the (2) Frame to Sash screws

as shown.

Install Chassis into

and Install

Front to Unit

Lift chassis and carefully slide it into installed

cabinet.

2. _ Do not push on controls OR

finned coils.You could damage unit, or cut

hands.

3. Be sure chassis is firmly seated towards rear of

cabinet.

4. Refer to Owner's Guide for front installation.

Thru-The-Wall Installation

NOTE: Consult local building codes prior to

installation, or a qualified carpenter.

Location

This air conditioner has a slide-out chassis, so it

can be installed through an outside wall up to

7" (178 mm) thick. IMPORTANT: Side louvers

must never be blocked.

NOTE: All parts needed for Thru-The-WaU

Installation are provided, except a wood frame,

shims, and 10 wood screws (#10-1" long minimum

(25 mm)). Select a wall surface that:

1. does not support major structural loads such

as the frame construction at ends of windows,

and under truss-bearing points, etc.

2. does not have plumbing or wiring inside.

3. is near existing electrical outlets, or where

another outlet can be installed.

4. faces, and is not blocked to the area to be

cooled.

5. allows unblocked airflow from rear sides and

end (outside) of installed air conditioner.

pare Wall

1. Prepare wall in frame construction (including

brick and stucco veneer).Working from inside

the room, find wall stud nearest the center of

area where air conditioner will be installed (by

sounding wall, or by magnetically finding

nails).

2. Cut or knock out a hole on each side of center

stud.

3. Measure between inside edges of every other

stud as shown in FIG. 1.

FIG. I

3-3/8"

(8.6 cm)

Carefully measure and cut an opening with the

following dimensions. See FIGS. 1 and 2.

WIDTH "X" = 24-1/4" plus twice the

thickness of framing material used.

HEIGHT "Y" = 15-1/4" plus twice the

thickness of framing material used.

FIG. 2

UPTO

4. Build a wooden sleeve with the INSIDE

dimensions of 24-1/4" in width and 15-1/4" in

height. Frame depth should be the same as

wall thickness. Fill in the space from the

opening to the studs with wood spacers,

as shown.

5. Nail frame to spacers with front flush with

drywall.

NOTE: If wall thickness is 7" (178 mm) or more,

add aluminum flashing over bottom of frame

opening to assure no water can enter area

between inner and outer wall. 1"LONG FIG. 2

ALUMINUM FLASHING

OVER BOTTOM OF FRAME

/'_ OVER

7" (178 mm)

OPTIONAL: Support brackets may be used.

Installation brackets are recommended for walls

under 5" thick.

Refer to Step 4 of Window Mounting for assembly

of support brackets.A wooden strip nailed to the

outside wall should be used in conjunction with

sill support angle brackets.

and Install

1. Slide chassis from cabinet. Refer back to Step 1

of Window Mounting.

2. Place cabinet into opening with bottom rail

resting firmly on bottom board of wooden

frame.

3. Position cabinet to achieve proper slope for

water removal. (See FIG. 1 below.)

FIG. I3/4" PLUS

_,_ I*--{---TRIM THICKNESS

.,I.b.----I SEE PARA 5

5/16_,' I I

;roI,-

LEVEL

port bracket

Wooden strip

Screw or nail cabinet to wooden frame using

shims if frame is oversized, to eliminate

distortion. Remember to maintain proper

slope as described in Step 3.

.Secure bottom rail to wood frame with two

large wood screws 1" (2.5 cm) long using the

two holes in the bottom of the channel resting

on frame. (See FIG. 2 following.)

6. Install chassis into cabinet by following all

steps in Step 8 of Window Mounting.

(continued)

OPTIONAL:Caulkingandinstallationof trim on

interior wall maybe done.Youcanbuywood

from your local lumber or hardware supply. On

the outside, caulk openings around top and sides

of cabinet, and all sides of wood sleeve to the

opening.

NOTE: See Step 7, Item 3 of Window Mounting

Instructions for bottom rail seal location.

Masonry Construction

1. Cut or build a wall opening in the masonry

wall similar to the frame construction (refer to

Step 2 of Thru-the-WaU Installation for a wall

thickness greater than 8-1/2").

.Secure cabinet in place using masonry nails, or

the right masonry anchor screws. (Another

way to do this is to build an in-between frame

of 2x4's (51 mm x 102 mm) as shown in the

Step 2 Prepare Wall illustrations-- but make it

double framed on either side, and install

between masonry wall opening and cabinet.

Frame must be securely anchored to masonry

wall opening.)This way gives very good

louver clearance on either side of cabinet.

3. Install a lintel to support masonry wall above

cabinet. Existing holes in cabinet can be used

and/or additional holes can be drilled to fasten

cabinet at various positions. Be sure that side

louver clearance is in accordance with Step 1

above.

4. Install exterior cabinet support brackets as

shown in Step 2 of Thru-the-Wall Installation.

Caulk or flash if needed, to provide a weather-

tight seal around top and sides of cabinet.

5. To complete installation, apply wood trim

molding around room side projection of

cabinet.

Tabla de contenidos

Otros manuales de Acondicionador de aire de Frigidaire

Frigidaire

Frigidaire 2020213A0362 Manual de usuario

Frigidaire

Frigidaire FAS155P1A1 Manual de usuario

Frigidaire

Frigidaire FAC106N1A Manual de usuario

Frigidaire

Frigidaire FRA065AT70 Manual del propietario

Frigidaire

Frigidaire FAS182P2A1 Manual de servicio

Frigidaire

Frigidaire FRA053XT7 Instrucciones de instalación

Frigidaire

Frigidaire LRA257ST217 Manual del propietario

Frigidaire

Frigidaire FAH14ER2T - 14,000-BTU Through-the-Wall Air... Manual de usuario

Frigidaire

Frigidaire FAC084K7A4 Manual de usuario

Frigidaire

Frigidaire FAC064L7A1 Manual de usuario

Frigidaire

Frigidaire FAS256N2A Manual de usuario

Frigidaire

Frigidaire FAS225P2A1 Manual de usuario

Frigidaire

Frigidaire FAR105S1A11 Manual de usuario

Frigidaire

Frigidaire FAC064J7A3 Manual de usuario

Frigidaire

Frigidaire FAX054P7A6 Manual de usuario

Frigidaire

Frigidaire FFRA0511R1 Manual del propietario

Frigidaire

Frigidaire CRA123KT11 Manual de usuario

Frigidaire

Frigidaire FRA122BU1 Manual de usuario

Frigidaire

Frigidaire FRA053XT71 Manual del propietario

Frigidaire

Frigidaire FRA144HT211 Manual de usuario

Frigidaire

Frigidaire FRA12EHT2 Manual de usuario

Frigidaire

Frigidaire FRS09PYS1 Instrucciones de instalación

Frigidaire

Frigidaire FAA063M7A1 Guía de inicio rápido

Frigidaire

Frigidaire FAC089L7A2 Manual de usuario

Manuales populares de Acondicionador de aire de otras marcas

Spheros

Spheros CC 355 Manual de usuario

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manual de usuario

Panasonic

Panasonic CS-E12HKEW Manual de usuario

nedis

nedis ACMB1WT7 Manual de usuario

Samsung

Samsung AR KV Series Guía

Daikin

Daikin FCFV50A Manual de usuario

Fujitsu

Fujitsu Inverter ASBA30JFC Manual de usuario

Toshiba

Toshiba RAS-M10SMUV-E Manual de usuario

Daikin

Daikin FXLQ20MAVE Manual de usuario

Hitachi

Hitachi RAS-E24CAK Manual de usuario

CIAT

CIAT Magister 2 Series Guía

Bestron

Bestron AAC6000 Manual de usuario

Hisense

Hisense 7K Manual técnico

Samsung

Samsung AS09HM3N Manual de usuario

Soleus Air

Soleus Air GB-PAC-08E4 Manual de usuario

McQuay

McQuay MCK020A Manual de usuario

Webasto

Webasto Frigo Top 25 DS Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Manual de usuario