Freewing Go 2.5 Manual de usuario
USER GUIDE
CONTENT
1. THE FREEWING
2. WIND CHART & RECOMMENDED PRESSURE
3. HOW TO INFLATE THE WING
4. HOW TO ATTACH YOUR LEASH
5. HOW TO TIE THE HARNESS LINES
6. HOW TO DEFLATE THE WING
7. SAFETY
RULE No.1: SAFETY FIRST
RULE No.2: SECURITY SYSTEMS
RULE No.3: RESPECT OTHERS
8. MAINTENANCE
BEFORE SESSION
DURING SESSION
AFTER SESSION
9. REPAIRS
10. STARBOARD/AIRUSH WARRANTY
03
04
05
07
08
11
13
13
15
15
16
16
16
16
17
19
- 3 -
THE FREEWING
01. Leading edge - Front side of the wing
02. Trailing edge - Back side of the wing
03. Wingtips
04. Central strut
05. Neutral handle
06. Leash attachment
07. Diagonal handles (Y-handles)
08. Front handles
09. Back handles
10. Leading edge valve + valve cover
11. Central strut valve + valve cover
12. Harness line attachment
13. Harness line (Not included /
Sold separately)
INCLUDED ACCESSORIES
• 1 x Wing bag
• 1 x Repair kit
• 1 x Waist leash
• 1 x Multi Adapter for SUP
pumps
1
7
4
2
3
8
13
12 12
9
6
5
10 11
- 4 -
WIND CHART &
RECOMMENDED
PRESSURE
SIZE CHART
Size: Wind Range: Recommended
Inflating Pressure:
22-40 knots 8 psi
Our wings are made for all weather conditions. They are powerful, maneuverable and
stable at full speed. The chart specifies the wind ranges and the recommended
inflation pressure. Too much inflation may result in the wing bursting.
Note: Chart relating to a 75 kg rider.
* Always be aware and responsible during your practice. Avoid extreme wind/wave
conditions and keep away from possible obstacles.
* Choose your wing size according to the windspeed .
* To our beloved science orientated customers, the pressure with which you need to inflate
the wing increases unevenly with the size of the wing. This is due to the fact that the force
applied on the surface can be approximately defined by F=P.S where F is the force, P the
Pressure and S the Surface.
2.5
18-32 knots 7 psi
3.5
12-28 knots 7 psi
4.5
10-24 knots 6 psi
5.5
8-20 knots 6 psi
6.5
- 5 -
HOW TO
INFLATE THE WING
1. Make sure the area where you want to pump the wing is free of sharp objects,
like rocks and fences.
2. Look for some windshade while pumping up the wing. In case you can’t find an
area with less wind, ask a friend to hold the wing while you pump.
3. Find out the wind direction, unfold your wing by laying it on the ground, struts
facing up with the wind blowing from your back.
4. Make sure the central strut valve is closed and screw the base of the valve
clockwise.
6. Attach the hook connector from the
pump to theleash'sknot. Alternatively,
attachthe leash of the wing to the
pump in order to prevent the wing
blowing away.
5. Spread the wing on the floor, make sure it does not have any creases. This
allows the air to flow in without deteriorating the wingtips.
CLOSED
7. Screw the base of the valve clockwise
into the thread on the Leading edge.
- 6 -
8. Connect the pump nozzle into the
valve of the wing. Turn clockwise
for a better insertion.
9. Inflate to the recommended pressure.
13. Put the harness lines in place using the ties made for this purpose – see
section “How To Tie The Harness Lines”, page 8.
14. Once you have put the leash on, the set up is ready! You can then use the leash
to keep the wing attached to a heavy and secure object while you go to set up
your board and put on your water clothes. Right on!
PSI
10. Open the central strut valve and
make sure that the base of the valve is
screwed clockwise.
11. Connect the pump nozzle into the
valve of the wing. Turn clockwise for
a better insertion.
12. Inflate to the recommended pressure.
PSI
- 7 -
HOW TO ATTACH
YOUR LEASH
The attachment point for the leash is in the front part of the FreeWing. It is
located close to the neutral handle in the center of the leading edge.
There are two quick and easy ways to attach your leash to the FreeWing.
a. Slide the end of the
leash through the loop
behind the knot.
b. Take the Velcro
bracelet and slide it
through the loop at
the end of the leash.
c. Pull the leash to tighten it.
1. Wrist and Waist leash attachment
a. Slide one end of the
leash’s Velcro through
the loop on the FreeWing
b. Close the different
Velcro overlaps
c. Pull firmly on the leash.
2. Surf leash attachment
- 8 -
HOW TO TIE
THE HARNESS LINE
We have designed our wings to offer you the best comfort while riding.
Harness lines make your navigation easier. Allowing you to put all your energy
into tricks and stay longer on the water!
How to correctly tie the lines
The harness line consists of two pieces, (a) shorter rope with different knots and
(b), longer rope with the black PVC attached.
There are two harness line attachment parts on the central strut, loop (A) and
loop (B).
a
b
A B
- 9 -
1. Insert the rope (a) into the loop (A).
2. Thread the end knot through the
loop (a).
3. Tighten it up and make sure that
loop (A) is being squeezed by the
knot.
4. Take piece (b) and do the same as
step “1” using the (B) loop instead.
A
A
A
a
B
b
a
a
- 10 -
5. Thread the end of the loop (the
shortest side) through the other
loop (longer side).
6. Tighten it up and make sure the
loop (B) is being squeezed by the
knot.
7. Connect the loop of piece (b) into
the knots of piece (a).
8. Adjust the length according to
your body structure using the
different knots.
B
b
B
b
B
1 2 3 4 5
b
a
b b b b b
a a
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
