Freetech P5F111 Manual de usuario
P5F111 User’s Manual 1
Copyright Notice
The information contained in the user’s manual and all accompa-
nying documentation is copyrighted and all rights are reserved.
This publication may not, in whole or in part, be reproduced,
transcribed, stored in a retrieval system, translated into any lan-
guage or computer language, or transmitted in any form whatso-
ever without the prior written consent from the manufacturer,
except for copies retained by the purchasers for their personal
archival purposes.
The manufacturer reserves the right to revise this user’s manual
and all accompanying documentation and to make changes in the
content without obligation to notify any person or organization of
the revision or change.
IN NO EVENT WILL THE VENDOR BE LIABLE FOR
DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSE-
QUENTIAL DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THIS PRODUCT OR DOCUMENTA-
TION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. IN PARTICULAR, THE VENDOR SHALL NOT
HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE,
OR DATA STORED OR USED WITH THE PRODUCT,
INCLUDING THE COSTS OF REPAIRING, REPLACING, OR
RECOVERING SUCH HARDWARE, SOFTWARE, OR
DATA.
All trademarks mentioned in this document are acknowledged.
The Specification on the manual is subject to change without
notice.
Copyright 1999.
C
2 P5F111 User’s Manual
Table Of Contents
Chapter 1
Introduction
1.1 Features
1.2 Specifications
1.3 What You Have
1.4 Precautions
1.5 Board Layout
1.5.1 Jumper Switches
1.5.2 Expansion Slots
1.5.3 Onboard Connectors
Chapter 2
Mainboard Installation
2.1 Installation Steps
2.2 Installing CPU
2.2.1 Setting the CPU Vcore Voltage
2.2.2 Setting the CPU I/O Voltage
2.2.3 Setting the CPU External Frequency
2.2.4 Setting the CPU to BUS Frequency Ratio
2.3 Installing Memory
2.4 Attaching Connectors
2.5 Set Jumpers on the Mainboard
4
8
10
11
12
13
13
14
17
17
19
19
20
21
22
23
31
P5F111 User’s Manual 3
Chapter 3
BIOS Configuration
3.1 Entering Setup
3.2 CMOS Setup Utility
3.3 Standard CMOS Setup
3.4 IDE HDD Auto Detection
3.5 Load Setup Defaults
3.6 Save & Exit Setup
3.7 Exit Without Saving
3.8 BIOS Features Setup
3.9 Chipset Features Setup
3.10 Power Management Setup
3.11 PnP/PCI Configuration
3.12 Integrated Peripherals
3.13 Supervisor/User Password
Chapter 4
Driver and Utility
4.1 Flash Utility
4.2 The steps to Install the VIA GRAT AGP Driver
4.3 The Steps to Install the VIA Bus Master PCI IDE Driver
4.4 The Steps to Install the VGA Driver
4.5 The Steps to Install the MVP4 Sound Card Driver
4.6 USB Driver
Appendix
System Environment Monitor
A.1 The Steps to Install the System Environment Monitor
Driver
34
36
36
36
36
37
40
52
52
43
47
49
51
33
32
53
54
56
55
55
4 P5F111 User’s Manual
1 Introduction
The P5F111 is a quality, high performance, function enhanced
mainboard based on the powerful Intel P54C/P55C, AMD K5/K6/K6-2/
K6-3, Cyrix 6x86/M II and IDE WinChip C6 family processor.
With a built-in VIA AGP graphics Chip, Ultra DMA-33/66 Bus
Mastering IDE controller, concurrent PCI bus, USB ports and built-in
AC97 Digital Audio Controller. It has 1MB or 2MB (optional) pipelined-
burst second-level cache on board and two Dual Inline Memory
Modules (DIMMs) allow as much as 512MB of 3V SDRAM/EDO
memory or 512MB of 3V EDO memory.
The board offers outstanding I/O capabilities, with Ultra DMA-33/66
Bus Mastering IDE interfaces, a floppy controller, two serial port
connectors, an EPP/ECP-capable parallel port connector, and IrDA-
compatible infrared port, two USB connectors, two USB ports, and
more. The three PCI local bus slots, two ISA bus slots, and one AMR
slot provide outstanding expandability for add-on peripheral cards.
In addition, the board features a synchronous switching regulator and
advanced power and system management functions. The board’s BIOS
supports automatic device detection--making setup of hard drives,
expansion cards, and other devices virtually automatic.
1.1 Features
This section presents an overview of the board’s special features.
VIA Apollo MVP4
The Apollo MVP4 is an advanced System Multimedia Architecture
(SMA) PC core logic chipset for Socket 7 PC systems. The VIA Apollo
MVP4 is a combination of the widely successful VIA Apollo MVP3
chipset and a high performance 2D/3D AGP graphics with setup engine
and DVD hardware acceleration (Tridert Blade 3D 9880). Paired with
the new VIA VT82C686A Super South bridge. The MVP4 is a
compelling solution for cost-effective, full-feature desktop and mobile
PC designs.
Chapter 1: Introduction
P5F111 User’s Manual 5
AGP VGA
Integrates an AGP 2.0 - Complaint 2D/3D AGP graphics controller into
the north bridge of the chipset, 64-bit 2D/3D graphics engine, and video
accelerator with advanced DVD video.
AC97 Audio
Integrated AC97 2.0 (meets PC 98(TM) Basic Audio Specification) and
Sound Blaster-compatible legacy audio.
ISA and PCI Expansion Slots
Provides two 16-bit ISA expansion slots and three 32-bit PCI expansion
slots.
Versatile Memory Configuration
The two DIMM sockets support up to 512MB of 3.3V SDRAM
memory. Synchronous Dynamic Random Access Memory (SDRAM)
provides optimized performance through increased data transfer rate.
Ultra DMA-33/66 Bus Mastering IDE Controller
Provides an Enhanced Intelligent Drive Electronics (IDE) hard disk
controller. Support for Ultra DMA-33/66 speeds up disk drive access.
Flash ROM BIOS and Enhanced ACPI
The programmable Flash ROM BIOS offers Advanced Configuration
and Power Interface (ACPI). ACPI enables ACPI-supported operating
systems (such as Windows 98) and applications to direct system power
management.
Synchronous Switching Regulator
The highly efficient synchronous switching design reduces power
consumption and heat generation.
External Modem Wakeup (Remote Ring On) (WOM)
With an optional phone line and modem, the board can turn on
automatically to answer a phone call.
Chapter 1: Introduction
6 P5F111 User’s Manual
Wake on LAN (WOL)
Provides a connector to an optional PCI LAN card (with remote
wakeup capabilities) so that a remote server can turn on the system
through a network.
RTC Walk-up Timer
The RTC wakeup timer can turn on your system at a predefined date and
time.
Dual-Function Power Button (Soft-Off Control)
Use the power button to turn off the system instantly or with “soft-off”
control. When soft-off is selected, pressing the power button will cause
the system to enter Sleep (Suspend) mode. With soft-off, the system
won’t turn off unless you continuously hold the power button for 4
seconds or longer. This prevents you from accidentally turning off the
system.
System Sleep (Suspend) Mode
To conserve energy, the system employs the following measures when
in Sleep (Suspend) mode:
The CPU stops running
The chipset and related circuits go to the lowest power state
The hard disk stops spinning
The monitor goes blank
The CPU cooling fan and system fan are turned off
The Power LED indicator on the front panel dims when the system
is in Suspend mode. (If you are using a 3-pin LED, it can display a
different color when the system is in Suspend mode).
Desktop Management Interface (DMI)
Supports DMI through the BIOS, which creates a higher level of
compatibility by allowing hardware to communicate with a standard
protocol.
Chapter 1: Introduction
P5F111 User’s Manual 7
Chapter 1: Introduction
Super Multi-I/O
Provides two high-speed UART-compatible serial ports and a parallel
port with EEP and ECP capabilities. For wireless connections, you can
connect an optional infrared module to the IrDA-compatible infrared
port.
Automatic Device Detection
Auto-detection support in BIOS makes installation of hard drives, and
other devices samples.
8 P5F111 User’s Manual
1.2 Specifications
Hardware
CPU Intel® P54C/P55C, AMD K5/K6/K6-2/K6-3, Cyrix
6x86/M II and IDE WinChip C6 Family
VRM Synchronous switching regulator; provides 1.3V to
3.5V operating voltage
Coprocessor CPU built-in floating point unit
Speed System bus clock 66/68/75/83/95/100/112MHz
PCI bus clock 27.7/31.75/33.3/34.25/37.5/37.75MHz
ISA bus clock 8.33MHz
Chipset VIA MVP4 (VT8501/VT82C686A)
EIDE Controller Dual-Channel Enhanced Intelligent Drive
Electronics (EIDE) interface supports up to 4
IDE hand disk drives or CD drives;
Supports PIO mode 0 through mode 4 drives;
Supports Bus Mastering DMA mode 2 drives and
Bus Mastering Ultra DMA-33/66 drives
Enhanced I/O Two serial ports (16550-compatible UART)
Parallel port with bidirectional lines supports
Standard Parallel Port (SPP), Enhanced
Parallel Port (EPP), and Extended
Capabilities Port (ECP)
IrDA-compatible infrared port
Mouse/Keyboard PS/2 mouse connector
PS/2 keyboard connector
Expansion Slots 3 X 32-bit PCI slots and 2 X 16-bit ISA slots
One AMR Slot
Chapter 1: Introduction
P5F111 User’s Manual 9
Power Management Compliant with EPA, APM 1.2 and ACPI
AT soft-off power control
ATX soft-off power control
Power - On by Keyboard & PS/2 mouse
Power - On by Modem Ring
Power - On by Alarm
Power - On by Network Card (WOL)
Sleep state indicator
Fan off in sleep mode
System Management VIA 686A include PC Health Monitor
Voltage Regulator Switching regulator
Form Factor AT Form Factor, 22.0cm x 24.0cm (7.25”x 7.9")
Software
BIOS AWARD AGP/PCI BIOS
2M-bit Flash BIOS with ESCD block
Supports APM, PnP, Multi-Boot, DMI and
EIDE devices
Supports Removable Media Drive
Driver Utility IDE Bus mastering Ultra DMA driver
Flash utility for BIOS upgrade
Hardware Doctor Utility
AGP VxD Driver
On Chip Trident AGP Driver
Audio drivers
O.S. Operates with MS_DOS 6.2x, Windows 3.x,
Windows 95, Windows 98, Windows NT4.x,
Window NT5x, OS/2 Warp 4.0, Novell
Netware, Novell UnixWare 1.1 and SCO Unix
5.0.x
Chapter 1: Introduction
10 P5F111 User’s Manual
Environment
Ambient Temperature 00C to 500C (Operating)
Relative Humidity 0 to 85% (Operating)
Vibration 0 to 500 Hz
DC Voltage 4.9V to 5.2V
DC Voltage 1.8 V to 3.50V
DC Voltage -5V, +12V, -12V, +5VSB 5% tolerance.
1.3 What You Have
The P5F111 mainboard comes securely packaged in a sturdy cardboard
shipping carton. In addition to this User’s Manual, the shipping carton
contains:
The mainboard
CD with support drivers and utilities OR Diskette with drivers and
utilities.
COM1, COM2, VGA, Sound, Printer, Floppy disk drive and IDE
ribbon cables
If any of these items is missing or damaged, contact the dealer from
whom you purchased the mainboard. Save the shipping materials
and carton in case you want to ship or store the board in the future.
Inside the carton, the mainboard is sandwiched between sheets of
sponge and packed in an anti-static bag. After you unpack the board,
inspect it for damage. Press down all the integrated circuits to make
sure they are properly seated in their sockets. Do not apply power to
the board if it appears to have been damaged.
Chapter 1: Introduction
Tabla de contenidos
Otros manuales de Placa madre de Freetech
Freetech
Freetech 586F52 Manual de usuario
Freetech
Freetech P8F152 Manual de usuario
Freetech
Freetech P8F217 Series Manual de usuario
Freetech
Freetech P6F70 Manual de usuario
Freetech
Freetech 586F62 Manual de usuario
Freetech
Freetech P8F150 Manual de usuario
Freetech
Freetech P6F117 Manual de usuario
Freetech
Freetech P8F155 Manual de usuario
Freetech
Freetech P5F113 Manual de usuario
Freetech
Freetech P8F161 Manual de usuario
Freetech
Freetech P8F154 Manual de usuario
Freetech
Freetech P6F125 Manual de usuario
Freetech
Freetech P5F87 Manual de usuario
Freetech
Freetech P5F97 Manual de usuario
Freetech
Freetech P6F212 Manual de usuario
Freetech
Freetech P6F77 Manual de usuario
Freetech
Freetech P6F135 Manual de usuario
Freetech
Freetech P8F148 Manual de usuario
Freetech
Freetech P8F161G-e Manual de usuario
Freetech
Freetech P5F97 Manual de usuario
Manuales populares de Placa madre de otras marcas
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manual de usuario
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Texas Instruments
Texas Instruments ADS8372EVM Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
