Franklin Electric VersaJet Series Manual de usuario

franklinwater.com

INLINE CONTROL PACKAGES

MH & VersaJet with SWC Controls

Installation and Operation Manual

Table of Contents

SAFETY INSTRUCTIONS - - - - - - - - 2

PRODUCT INFORMATION - - - - - - - 3

Description - - - - - - - - - - - 3

Related Documents - - - - - - - 3

Models - - - - - - - - - - - - - 3

INSTALLATION AND SETUP - - - - - - 4

Physical Installation - - - - - - - 4

Electrical Supply - - - - - - - - - 5

Priming the System - - - - - - - 5

OPERATION - - - - - - - - - - - - - 6

Inline Control Panel - - - - - - - 6

System Start/Stop Operation - - - 6

Troubleshooting - - - - - - - - - 6

STANDARD LIMITED WARRANTY - - - 7

SAFETY INSTRUCTIONS

Hazard Messages

SAFETY INSTRUCTIONS

Hazard Messages

This manual includes safety precautions and other important

information in the following formats:

IMPORTANT: Identifies information that controls correct assem-

bly and operation of the product.

NOTE: Identifies helpful or clarifying information.

This symbol alerts the user to the presence of dangerous

voltage inside the product that might cause harm or elec-

trical shock.

This symbol alerts the user to the presence of hot sur-

faces that might cause fire or personal injury.

Before Getting Started

This equipment should be installed and serviced by technically

qualified personnel who are familiar with the correct selection

and use of appropriate tools, equipment, and procedures. Failure

to comply with national and local electrical and plumbing codes

and within Franklin Electric recommendations may result in elec-

trical shock or fire hazard, unsatisfactory performance, or equip-

ment failure.

Read and follow instructions carefully to avoid injury and prop-

erty damage. Do not disassemble or repair unit unless described

in this manual.

Failure to follow installation or operation procedures and all

applicable codes may result in the following hazards:

Indicates an imminently hazardous situation

which, if not avoided, will result in death or

serious injury.

Indicates a potentially hazardous situation

which, if not avoided, could result in death or

serious injury.

Indicates a potentially hazardous situation

which, if not avoided, could result in minor or

moderate personal injury.

Indicates a potentially hazardous situation

which, if not avoided could result in damage to

equipment or other property.

High voltages capable of causing severe

injury or death by electrical shock are

present in this unit.

• To reduce risk of electrical shock, disconnect power before

working on or around the system. More than one discon-

nect switch may be required to de-energize the equipment

before servicing.

• Make sure the ground terminal is connected to the motor,

control enclosures, metal plumbing, and other metal near

the motor or cable using wire no smaller than motor cable

wires.

• Wire pump system for correct voltage.

Risk of bodily injury, electric shock,

or property damage.

• This equipment must not be used by children or persons

with reduced physical, sensory or mental abilities, or lack-

ing in experience and expertise, unless supervised or

instructed. Children may not use the equipment, nor may

they play with the unit or in the immediate vicinity.

• Equipment can start automatically. Lockout-Tagout before

servicing equipment.

• Operation of this equipment requires detailed installation

and operation instructions provided in this manual for use

with this product. Read entire manual before starting

installation and operation. End User should receive and

retain manual for future use.

• Do not use motor in swimming areas.

Risk of damage to pump or other equipment.

• Periodically inspect pump and system components. Regu-

larly check hoses for weakness or wear, making certain

that all connections are secure.

• Schedule and perform routine maintenance as required.

PRODUCT INFORMATION

Description

PRODUCT INFORMATION

Description

This constant pressure system consists of an SWC Inline Control attached to one of two different surface

pumps (VersaJet model shown). The control activates the pump as water is used. Once the water flow stops,

the control turns off the pump. This protects the pump in case of a water shortage or dry run event. This

product uses 115 volts via a plug-in cord for power.

The VersaJet pump is designed to work in well conditions that have a

suction lift of 25’ or less. The MH pump is intended provide a water

pressure boost over what is being supplied through a pressurized

main, but is also capable of operation where a suction lift of up to 10' is

needed.

Features

Configuration

• Pump needed for shallow well or water main pressure boosting

application

• Simple set up with no programming or adjustment necessary on

the equipment

• No additional pressurized bladder tank is needed in the installa-

tion.

Inline Control

• Flow based pump activation

• Run Dry protection

• System maintains water pressure in the plumbing for immediate

use, and includes a low pressure sensor to activate the unit if a

low pressure event occurs

• Automatic system reset/restart after a power loss or an out of water event.

Operation

• Control has LED indicators for system status and troubleshooting

• Manual reset required after a 24 hour Automatic Reset period

• Manual Reset pushbutton can be used to start the pump at any time.

Related Documents

Visit www.franklinwater.com/products to download.

VersaJet Owner’s Manual: 106537101

MH Series Pump Owner’s Manual: 106592101

SWC Inline Control Owner’s Manual: 998075003

Models

Model No. Description HP Order No. Weight

FVJ05CI VersaJet Series 0.5 91180105 31

FVJ07CI VersaJet Series 0.75 91180107 34

15FMH05S2 MH Series 0.5 96061505 22

15FMH07S3 MH Series 0.75 96061506 25

FIL-SWC16 Inline SWC Up to 2 HP 91987103 N/A

INSTALLATION AND SETUP

Surface Pump Constant Pressure System

INSTALLATION AND SETUP

Surface Pump Constant Pressure System

The drawing illustrates how a typical surface pump system should be arranged in the plumbing system.

1. Franklin Electric Pump/Motor: (MH series pump shown) Refer to the

appropriate Pump Manual for detailed pump and pipe information. Refer

to “Related Documents” on page 3.

2. SWC Inline Control

3. Water Supply Pipe

4. Discharge Pipe

NOTE: If a pressure relief valve is installed, it must be able to pass full

pump flow at 100 PSI.

Physical Installation

Environmental Requirements

Choose a clean, well-ventilated location that affords protection from freezing, flooding, and excessive heat.

In addition, it should provide access for servicing and allow convenient draining of the pump, tank, and ser-

vice pipes. A prepared foundation is not essential, provided the surface is hard and level. It can be located in

the basement or utility room of your house, at the well, or between the house and the well.

When installing outside of the house, the pump should be protected by a pump house with auxiliary heat to

prevent possible freezing.

A pump performs best when installed close to the well, reducing suction lift and friction losses.

Installation

1. Place the pump/control on a level, solid surface.

2. Plumb the water supply and discharge lines. The supply plumbing line should have proper backflow

prevention measures, such as a check valve or foot valve.

3. A tee fitting is recommended for mounting accessories such as a pressure gauge or a pressure relief

valve.

Refer to the VersaJet Owner’s Manual 106537101 or the MH Series Pump Owner’s Manual 106592101 for

detailed instructions for mounting accessories.

These are available on the Franklin Electric website: 35T35TUwww.franklinwater.comU35T.

INSTALLATION AND SETUP

Electrical Supply

A nearby 115 VAC GFCI outlet is required to run the pump and inline control.

Branch Circuit Protection

Integral solid state short circuit protection does not provide branch circuit protection. Branch circuit protec-

tion must be provided in accordance with the National Electrical Code and any additional local codes, or the

equivalent.

Ground Connections

Priming the System

Pump should not be primed until all plumbing is complete.

1. Remove the pump’s priming plug and fill the pump case and

supply suction line with clean water.

2. Reinstall the priming plug.

3. Open one discharge fixture (like a faucet). This allows any air to

escape and allows water to run through the pump, control, and

plumbing when power is applied.

4. Plug the electrical cord into a 115 VAC GFCI outlet. On the Inline

Control, you see the green Power On LED turns on.

5. Water should flow from the open discharge fixture. On the

Inline Control, the yellow Pump On LED turns on, indicating water

flow.

6. Press the control restart/reset button to run the pump again for

another priming cycle, see below for further details.

Priming is considered complete when water flows from the open

discharge fixture. At this time, the discharge fixture can be closed.

The system is ready for use.

Correcting No Water Flow

If the pump stops before water flows, and the red Fault LED blinks,

attempt to re-prime the system.

1. Unplug the system from the power outlet.

2. Remove the priming plug from the pump.

3. Refill the pump case and supply suction line with water as needed.

4. Replace the priming plug.

5. Connect the SWC Inline control power cord into the power outlet.

6. Press the Reset Button on the front of the inline control.

The Reset button runs the pump for 10 seconds. If still no water flow, you may need to repeat the above

steps until the discharge line fills with water from the pump.

Risk of damage to system, or malfunction can occur.

• Ensure that the system is properly grounded all the way to the service entrance panel.

• Make sure a service entrance ground rod is properly installed and connected.

OPERATION

Inline Control Panel

OPERATION

Inline Control Panel

System Start/Stop Operation

The inline control is factory calibrated to turn on the pump when the detected system pressure drops below

22 psi (1.5 bar) or it measures a flow demand of 0.25 gpm (1 L/min). If either event is measured by the sys-

tem, the control should turn on the pump. The pump must produce 20 psi (1.4 bar) beyond the low pressure

activation point of 22 psi. For example, if the pump starts on a low pressure of 22 psi, the pump shut-off

pressure must be greater than 42 psi (2.9 bar).

Additionally, to ensure that the low pressure cut-in functions properly, the maximum vertical distance

between the pump and the highest discharge outlet should be limited to 50 feet (15 m).

For further Inline Control information, refer to the Inline Control Owner’s Manual #998075003.

Automatic Restart

In the event of a run dry situation, the device will automatically make 10 attempts to restart over the next 24

hours at various set time intervals. Each attempt lasts approximately 5 seconds to allow for prime, if

required. After an unsuccessful 24-hour period, the red LED will blink and you must press the “Restart” but-

ton to perform a manual reset.

NOTE: In the event of a power outage, the device will automatically reset after power is restored.

Troubleshooting

In most situations, the pump is directly above the water source. This allows the inline control to be used with

surface pump. Even though the inline control has a built-in check valve, you must install appropriate check

valves or a foot valve to ensure the suction line holds water for continued priming and operation.

Additional troubleshooting information is found in the separate pump and inline control owner’s manuals.

Refer to “Related Documents” on page 3 for pump and control manuals.

Water System Plumbing Leaks:

All water leaks within the plumbing system should be corrected for optimal performance of the system. If

water leaks cannot be corrected or mitigated, to prevent frequent pump starts, an optional pressurized

bladder expansion tank should be installed with an internal water draw down capacity capable of support-

ing the pump start frequency desired. The air pressure charge of this tank should be set to roughly the same

as the system’s working pressure.

The Inline Control panel has LEDs and the Restart button.

Green LED on Power On Device has power available

Yellow LED on Pump On Pump is running

Red LED blinking Fault Low or No Water Flow

Button Restart Press Restart after failure/fault

STANDARD LIMITED WARRANTY

Except as set forth in an Extended Warranty, for one (1) year from the date of installation, but in no event more than two (2) years from

the date of manufacture, Franklin hereby warrants to the purchaser (“Purchaser”) of Franklin’s products that, for the applicable warranty

period, the products purchased will (i) be free from defects in workmanship and material at the time of shipment, (ii) perform consis-

tently with samples previously supplied and (iii) conform to the specifications published or agreed to in writing between the purchaser

and Franklin. This limited warranty extends only to products purchased directly from Franklin. If a product is purchased other than from

a distributor or directly from Franklin, such product must be installed by a Franklin Certified Installer for this limited warranty to apply.

This limited warranty is not assignable or transferable to any subsequent purchaser or user.

a. THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, WRITTEN OR ORAL, STATUTORY, EXPRESS, OR IMPLIED,

INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. PURCHASER’S SOLE AND EXCLU-

SIVE REMEDY FOR FRANKLIN’S BREACH OF ITS OBLIGATIONS HEREUNDER, INCLUDING BREACH OF ANY EXPRESS OR IMPLIED

WARRANTY OR OTHERWISE, UNLESS PROVIDED ON THE FACE HEREOF OR IN A WRITTEN INSTRUMENT MADE PART OF THIS LIM-

ITED WARRANTY, SHALL BE FOR THE PURCHASE PRICE PAID TO FRANKLIN FOR THE NONCONFORMING OR DEFECTIVE PRODUCT

OR FOR THE REPAIR OR REPLACEMENT OF NONCONFORMING OR DEFECTIVE PRODUCT, AT FRANKLIN’S ELECTION. ANY FRANK-

LIN PRODUCT WHICH FRANKLIN DETERMINES TO BE DEFECTIVE WITHIN THE WARRANTY PERIOD SHALL BE, AT FRANKLIN’S SOLE

OPTION, REPAIRED, REPLACED, OR A REFUND OF THE PURCHASE PRICE PAID. Some states do not allow limitations on how long an

implied warranty lasts, therefore, the limitations and exclusions relating to the products may not apply.

b. WITHOUT LIMITING THE GENERALITY OF THE EXCLUSIONS OF THIS LIMITED WARRANTY, FRANKLIN SHALL NOT BE LIABLE TO THE

PURCHASER OR ANY THIRD PARTY FOR ANY AND ALL (i) INCIDENTAL EXPENSES OR OTHER CHARGES, COSTS, EXPENSES

(INCLUDING COSTS OF INSPECTION, TESTING, STORAGE, OR TRANSPORTATION) OR (ii) DAMAGES, INCLUDING CONSEQUENTIAL,

SPECIAL DAMAGES, PUNITIVE OR INDIRECT DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS, LOST TIME AND LOST

BUSINESS OPPORTUNITIES, REGARDLESS OF WHETHER FRANKLIN IS OR IS SHOWN TO BE AT FAULT, AND REGARDLESS OF

WHETHER THERE IS OR THERE IS SHOWN TO HAVE BEEN A DEFECT IN MATERIALS OR WORKMANSHIP, NEGLIGENCE IN MANU-

FACTURE OR DESIGN, OR A FAILURE TO WARN.

c. Franklin’s liability arising out of the sale or delivery of its products, or their use, whether based upon warranty contract, negligence,

or otherwise, shall not in any case exceed the cost of repair or replacement of the product and, upon expiration of any applicable

warranty period, any and all such liability shall terminate.

d. Without limiting the generality of the exclusions of this limited warranty, Franklin does not warrant the adequacy of any specifica-

tions provided directly or indirectly by a purchaser or that Franklin’s products will perform in accordance with such specifications.

This limited warranty does not apply to any products that have been subject to misuse (including use in a manner inconsistent with

the design of the product), abuse, neglect, accident or improper installation or maintenance, or to products that have been altered

or repaired by any person or entity other than Franklin or its authorized representatives.

e. Unless otherwise specified in an Extended Warranty authorized by Franklin for a specific product or product line, this limited war-

ranty does not apply to performance caused by abrasive materials, corrosion due to aggressive conditions, or improper voltage

supply.

f. With respect to motors and pumps, the following conditions automatically void this limited warranty:

1. Mud or sand deposits which indicate that the motor has been submerged in mud or sand.

2. Physical damage as evidenced by bent shaft, broken or chipped castings, or broken or bent thrust parts.

3. Sand damage as indicated by abrasive wear of motor seals or splines.

4. Lightning damage (often referred to as high voltage surge damage).

5. Electrical failures due to the use of non-approved overload protection.

6. Unauthorized disassembly.

800.348.2420 | franklinwater.com

For technical assistance, please contact:

Form 998075008 Rev. 000 07/19

ESPAÑOLES

franklinagua.com

PAQUETES DE CONTROL EN LÍNEA

MH & VersaJet con controles SWC

Manual de instalación y funcionamiento

Índice

INSTRUCCIONES SOBRE SEGURIDAD - 10

INFORMACIÓN SOBRE EL PRODUCTO - 11

Descripción - - - - - - - - - - - 11

Documentos relacionados - - - - 11

Modelos - - - - - - - - - - - - - 11

INSTALACIÓN Y CONFIGURACIÓN - - - 12

Instalación física - - - - - - - - - 12

Suministro eléctrico - - - - - - - 13

Cebado del sistema - - - - - - - 13

FUNCIONAMIENTO - - - - - - - - - - 14

Panel de control en línea - - - - - 14

Operación de arranque/parada - - 14

Solución de problemas - - - - - - 14

GARANTÍA LIMITADA ESTÁNDAR - - - 15

INSTRUCCIONES SOBRE SEGURIDAD

Mensajes de peligro

INSTRUCCIONES SOBRE SEGURIDAD

Mensajes de peligro

Este manual incluye precauciones de seguridad y otra

información importante en los siguientes formatos:

IMPORTANTE: Identifica información que controla el

ensamblaje y el funcionamiento correctos del producto.

NOTA: Identifica información útil o aclaratoria.

Este símbolo alerta al usuario sobre la presencia de un

voltaje peligroso dentro del producto que podría

provocar lesiones o descargas eléctricas.

Este símbolo alerta al usuario sobre la presencia de

superficies calientes que podrían provocar incendios

o lesiones personales.

Antes de empezar

La instalación y el mantenimiento de este equipo deben estar

a cargo de personal con capacitación técnica. El hecho de no

cumplir con los códigos eléctricos nacionales y locales y con las

recomendaciones de Franklin Electric puede provocar peligros de

descarga eléctrica o incendio, desempeños insatisfactorios

o fallas del equipo.

Lea y siga las instrucciones cuidadosamente para evitar lesiones

y daños a los bienes. No desarme ni repare la unidad salvo que

esté descrito en este manual.

El hecho de no seguir los procedimientos de instalación/

funcionamiento y todos los códigos aplicables puede ocasionar

los siguientes peligros:

Indica una situación inminentemente peligrosa

que, de no evitarse, provocará una muerte

o lesiones graves.

Indica una situación potencialmente peligrosa

que, de no evitarse, puede provocar una

muerte o lesiones graves.

Indica una situación potencialmente peligrosa

que, de no evitarse, puede provocar lesiones

menores o moderadas.

Indica una situación potencialmente peligrosa

que, de no evitarse, puede provocar daños al

equipo u otros bienes.

Esta unidad tiene voltajes elevados que

son capaces de provocar lesiones

graves o muerte por descarga eléctrica.

• Para reducir el riesgo de descarga eléctrica, desconecte la

energía antes de trabajar en el sistema o cerca de él. Es

posible que sea necesario más de un interruptor de

desconexión para cortar la energía del equipo antes de

realizarle un mantenimiento.

• Asegúrese de que la terminal de conexión a tierra esté

conectada al motor, los gabinetes de control, las tuberías

metálicas y otras partes metálicas cercanas al motor o un

cable con un alambre que no sea menor a los alambres del

cable del motor.

• Cablee el sistema de bombeo para los voltajes correctos.

Riesgo de lesiones corporales, descargas

eléctricas o daños al equipo.

• Este equipo no deben usarlo niños ni personas con capaci-

dades físicas, sensoriales o mentales reducidas, ni aquel-

los que carezcan de experiencia y capacitación, salvo que

estén bajo supervisión o instrucción. Los niños no podrán

usar el equipo ni jugar con la unidad o en las cercanías

inmediatas.

• El equipo puede encenderse en forma automática. Realice

los procedimientos de bloqueo/etiquetado antes de efec-

tuar el mantenimiento del equipo.

• El funcionamiento de este equipo exige instrucciones

detalladas para su instalación y funcionamiento que se

encuentran en este manual para su uso con este producto.

Lea la totalidad del manual antes de comenzar la insta-

lación y el funcionamiento. El usuario final debe recibir

y conservar el manual para usos futuros.

• No use el motor en áreas de natación.

Riesgo de daños a bomba u otros equipos.

• Inspeccione periódicamente los componentes del sistema

y la bomba. Revise regularmente las mangueras para con-

trolar si están débiles o gastadas y asegúrese de que todas

las conexiones sean seguras.

• Programe y realice servicios de mantenimiento de rutina.

Otros manuales para VersaJet Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Bomba de agua de Franklin Electric

Franklin Electric

Franklin Electric MH Series Manual de usuario

Franklin Electric

Franklin Electric Little Giant WGFP-50 Manual de usuario

Franklin Electric

Franklin Electric Little Giant VCC-20S Manual de usuario

Franklin Electric

Franklin Electric IPS Manual de usuario

Franklin Electric

Franklin Electric VR Series Manual de usuario

Franklin Electric

Franklin Electric 3NC-323P1-184 Manual de usuario

Franklin Electric

Franklin Electric LittleGIANT MGP-1C18-2 Manual de usuario

Franklin Electric

Franklin Electric Little GIANT 10E-CIA-SFS Manual de usuario

Franklin Electric

Franklin Electric E-Tech Manual técnico

Franklin Electric

Franklin Electric SR Series Manual de usuario

Franklin Electric

Franklin Electric Red Lion RL-50 Manual de usuario

Franklin Electric

Franklin Electric B50S Manual de usuario

Franklin Electric

Franklin Electric FTT Series Manual de usuario

Franklin Electric

Franklin Electric FS Series Manual de usuario

Franklin Electric

Franklin Electric LittleGIANT HT-10EN-CIM Manual de usuario

Franklin Electric

Franklin Electric Little Giant BPLA Series Manual de usuario

Franklin Electric

Franklin Electric Little Giant OS3 Manual de usuario

Franklin Electric

Franklin Electric Little Giant VCMA Series Manual de usuario

Franklin Electric

Franklin Electric E-Tech ES-VN-VL Manual técnico

Franklin Electric

Franklin Electric Little Giant 16 G Series Manual de usuario

Franklin Electric

Franklin Electric Little GIANT 9EC Series Manual de usuario

Franklin Electric

Franklin Electric DA1A Manual de usuario

Franklin Electric

Franklin Electric Hydropompe FWS Series Instrucciones de operación

Franklin Electric

Franklin Electric PES Series Manual de usuario

Manuales populares de Bomba de agua de otras marcas

Neptun

Neptun NPHW 5500 Manual de usuario

Sensidyne

Sensidyne Gilian BDX-II Instrucciones de instalación y funcionamiento

Draper

Draper 47808 Manual de usuario

Trolla

Trolla 12820 Manual de usuario

Sunfab

Sunfab SVH Series Manual de usuario

WilTec

WilTec 50740 Manual de usuario

Fieldmann

Fieldmann FVC 5015 EK Manual de usuario

Everbilt

Everbilt EFSUB5-122HD Manual de usuario

Graco

Graco Husky 3300e Manual de usuario

esotec

esotec 101018 Manual de usuario

moyno

moyno 2000 CC Manual de usuario

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manual de usuario

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guía de solución de problemas

DUROMAX

DUROMAX XP WX Series Manual de usuario

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manual de usuario

Xylem

Xylem e-1532 Series Manual de usuario

Milton Roy

Milton Roy PRIMEROYAL Manual de usuario

STA-RITE

STA-RITE ST33APP Manual de usuario