Franklin Electric Inline 1100 Manual de usuario

Inline Constant

Pressure System

Owner's Manual

s WARNING

Before Getting Started

Read and follow safety instructions. Refer to product data plate(s) for additional operating

instructions and specications.

s CAUTION

RISK OF ELECTRIC SHOCK - This pump is supplied with a grounding conductor and grounding type

attachment plug. To reduce risk of electric shock, be certain that it is connected only to a properly

grounded, grounding-type receptacle. Disconnect power before working on or around the Inline system.

Do not use the Inline system in swimming areas.

This equipment should be installed by technically qualied personnel. Failure to install it in compliance

with national and local electrical codes and within Franklin Electric recommendations may result in

electrical shock or re hazard, unsatisfactory performance, or equipment failure. Installation information

is available through pump manufacturers and distributors, or directly from Franklin Electric at our toll-

free number 1-800-348-2420.

This equipment must not be used by children or persons with reduced physical, sensory or mental

abilities, or lacking in experience and expertise, unless supervised or instructed. Children may not use

the equipment, nor may they play with the equipment or in the immediate vicinity.

If the power cord is damaged, it must only be replaced by qualied personnel.

• Keep work area clean, well-lit, and uncluttered.

• Keep safety labels clean and in good condition.

• Wear safety glasses while installing or performing maintenance on pump.

• Do not run pump dry. Fill pump with water before starting or pump will be damaged.

• Make sure all ELECTRICAL POWER IS OFF before connecting any electrical wires. Wire Inline

Pressure Boosting System for correct voltage. Follow all pump wiring instructions provided in the

"Wiring" section of this manual.

s WARNING

This is the safety alert symbol. When you see this symbol on your pump or in this manual, look for

one of the following signal words and be alert to the potential for personal injury:

s WARNING

DANGER

s WARNING

NOTICE

warns about hazards that will cause serious personal injury, death or major

property damage if ignored.

warns about hazards that can cause serious personal injury, death or

major property damage if ignored.

warns about hazards that will or can cause minor personal injury or major

property damage if ignored.

indicates special instructions which are important but not related to hazards.

Carefully read and follow all safety instructions in this manual and on pump.

WARNINGWARNING

Table of Contents

Before Getting Started .............................................................2

Key Features ....................................................................4

Inspect Your Shipment .............................................................4

Constant Pressure Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation of Inline Constant Pressure System..........................................6

Operation of the Inline Constant Pressure System ......................................12

Drive DIP Switch Options..........................................................14

Maintenance of the Inline Constant Pressure System ....................................15

Replacement Parts...............................................................16

Troubleshooting .................................................................18

Appendix 1 - Inline System Performance Curve ........................................19

Appendix 2 - Friction Loss Tables ...................................................20

Limited Warranty ................................................................23

Inline Constant Pressure System

Inline System Key Features

System Features:

• Constant water pressure with a wide range of settings (25-80 psi, 1.7 - 5.5 bar)

• Pump speed is controlled to provide the optimum performance without overloading the motor

• Product Power Rating: 1.2 hp (0.9 kW)

• Low current motor start-up (soft-starting)

• Quiet operation

• Single pump/motor/drive controller design

• Compact footprint, 19 in x 8 in (480 mm x 200 mm)

• Shipping weight: 50 lbs (22.7 kg)

Pump Features:

• Operates on a wide range of ows from ooded suction to 35 gpm (135 lpm)

• Requires minimum incoming pressure of 3 psi (0.2 bar) Exception: Cisterns may be ooded

suction without vortexing

• Increases incoming pressure by up to 60 psi (4.1 bar)

• Stainless steel construction for all wetted surfaces

Drive Controller Protection Features:

• No in-rush (power-on transient) current

• Over-pressure shuto optional (see Replacement Parts section)

• Low water shut-o

• Locked pump detection/shut-o

• Water over-temperature shut-o

• High voltage/lightning surge protection

• Low line voltage protection

• Motor under and overload protection

• Open and short circuit protection

• NEMA 4 enclosure

INSPECT YOUR SHIPMENT

All Franklin Electric Inline Systems are carefully tested, inspected, and packaged to ensure their

arrival in perfect condition. When the pump is received, examine it closely to make sure there is

no damage that may have occurred in shipping. If damage is evident, report this immediately to

your shipping carrier and product dealer. The shipping carrier assumes full responsibility for the

shipment’s safe arrival. Any claim for damage to the shipment, either visible or concealed, must

be made through the shipping carrier rst.

Package Includes:

• Inline 1100 Constant Pressure System pump and controller unit

• Pressure sensor and boot

• Sensor adjustment tool

• Installation manual

Inline Constant Pressure System

Constant Pressure Introduction

The Franklin Electric Inline System provides consistent water pressure regulation using advanced

electronics to drive the pump/motor according to the system’s real-time demand. The water

pressure demand is under constant monitoring through a highly accurate, heavy-duty, long-life

pressure sensor, which is included with and wired into the system at the time of installation. By

adjusting the pump/motor speed, the Inline System automatically reacts to any change in system

demand while maintaining a constant output pressure. The Inline System’s constant output

pressure should not uctuate more than a psi or two, even though the overall system’s water

ow requirement may change dramatically. For example, a small demand on the system, such as

a bathroom faucet, results in the motor/pump running at its lowest speed. As greater demands

are placed on the system, such as opening additional faucets or using appliances, the speed

increases accordingly to maintain the desired system pressure.

System Diagnostics

In addition to regulating pump pressure and accurately controlling motor operation, the Inline

System continuously monitors system performance and can detect a variety of abnormal

conditions. In many cases, the controller will compensate as needed to maintain continuous

system operation. But, if there is high risk of equipment damage, the controller will protect the

system by shutting itself down. To help identify that there is a problem with the system (which

includes incoming water and electricity from the utility company), the Inline System will display

that there is a fault condition. See Troubleshooting section for fault codes. If possible, the

controller will try to restart when the fault condition subsides.

Water Over-Temperature Shut-Off

In the event of inadequate water supply, such as closure of the incoming water supply or system

component failure, the unit has a potential to run continuously. This operation can allow for

heating of the water inside the Inline System. To reduce the amount of heating, Inline Systems are

equipped with a thermal cuto switch. See Troubleshooting section for fault codes. Once the Inline

System cools, the unit will automatically resume operation.

Thermal Temperature Limits:

Maximum shut-o temperature - 150 °F (65 °C)

Minimum reset temperature - 118 °F (48 °C )

Inline Constant Pressure System

INSTALLATION

Location of the Inline Constant Pressure System

Decide on a location for the pump installation that is suitable based on the enclosure rating of the

Inline System.

Liquid-tight conduit and ttings must be used to maintain NEMA 4 rating.

This equipment must not be used by children or persons with reduced

physical, sensory or mental abilities, or lacking in experience and

expertise, unless supervised or instructed. Children may not use the

equipment, nor may they play with the unit or in the immediate vicinity.

Choose a clean, well-ventilated location that provides protection from freezing, ooding, and

excessive heat. In addition, it should provide access for servicing and allow convenient draining of

the pump, tank, and service pipes. A prepared foundation is not essential, provided the surface is

hard and level. It can be mounted in any orientation depending on the space available.

Installation in direct sunlight can reduce system power and reduce

drive life.

Plumbing, Piping, and Hoses

In general, keep the suction and discharge lines as large as possible. Avoid using bends, elbows,

and ttings whenever possible. All suction connections must be airtight, so use pipe compound on

all threaded joints. Use a suction strainer when applicable to prevent solids and foreign matter from

being drawn into the pump.

Flow Capacity by Pipe Size

The minimum supply pipe diameter should be selected not to exceed a maximum water velocity of

8 ft/sec (2.4 m/s). Use the table below for selection of the proper supply pipe size.

Water Supply Requirement

The Inline System is not designed to draw/lift water from a source below the pumping unit. There is

not an incoming ow requirement, other than that the system needs to be supplied with a constant

supply of water to keep the unit completely full of water at all times. It is recommended that the

system be supplied with inlet line ¾" diameter or larger.

s WARNING

WARNING

s WARNING

NOTICE

s WARNING

WARNING

Minimum Pipe Diameter Maximum Flow Rate GPM

1/2" 4.9 (18.5 lpm)

3/4" 11.0 (41.6 lpm)

1" 19.6 (74.2 lpm)

1-1/4" 30.6 (116 lpm)

1-1/2" 44.1 (167 lpm)

Inline Constant Pressure System

Incoming Pressure Requirement

The Inline System is designed to operate as low as 3 psi (0.2 bar) at minimum incoming pressures.

When used on a cistern, the incoming pressure requirement is waived, but a water level must be

maintained in the cistern to prevent a vortex from forming.

Failure to maintain incoming water may result in heating of water,

personal injury, pump damage and/or property damage.

Suction Piping

When the pump is located at a distance from the water source, the suction piping may have to be

increased in diameter to reduce friction loss. The friction loss in a system increases:

1. As the ow rate increases

2. As the piping size decreases

Refer to the included Inline System’s performance tables (Appendix 1) and friction loss tables

(Appendix 2) to determine the amount of head lost for a given application.

Discharge Pipe Sizes for Installation

When the pump is located at a distance from points of water use, it is necessary to increase the

discharge pipe size in order to reduce friction loss. The friction loss in a system increases:

1. As the ow rate increases

2. As the piping size decreases

Refer to the included Inline System’s performance tables (Appendix 1) and friction loss tables

(Appendix 2) to determine the amount of head lost for a given application.

Pressure Tank

The Inline System needs a small pressure tank placed on the pump outlet to maintain constant

pressure. The tank supplies water while the pump ramps up to speed and in circumstances where

only a small amount of water is required for a short period of time. In addition, the tank prevents

water hammer by acting as a system buer. This buer also helps to prevent pressure spikes

when there is a sudden change in demand.

s WARNING

WARNING

System Pressure

(at Pressure Sensor)

Pressure Tank

Setting (±2 PSI)

25 18

30 21

35 25

40 28

45 32

50 Factory Setting 35

55 39

60 42

65 46

70 49

75 53

80 56

NOTE: 1 psi = 0.068 bar

Inline Constant Pressure System

For 12 gpm (45 lpm) ow or greater, minimum pressure tank size is 4 gallons (15 L);

for 12 gpm (45 lpm) ow, minimum pressure tank size is 2 gallons (7.5 L).

Pressure Tank Pre-charge (PSI)

The pressure tank pre-charge setting should be 70% of the system pressure sensor setting as

indicated in the preceeding table.

NOTE: Tank pre-charge should be maintained for optimum pressure regulation.

Pressure tank failure may prevent the pump from shutting o. A run-

on condition can heat the water in the pump, which may cause pump

failure, plumbing failure, and/or personal injury.

Failure to install a pressure tank will prevent the pump from shutting

o. FAILURE TO FOLLOW THIS WARNING may result in heating of

water, personal injury, pump damage, and/or property damage.

INSTALLATION

Notice: Read and Follow All Instructions

Hazardous voltage can shock, burn or cause death.

Improper wiring can result in permanent damage to the system. Pump

connection must comply with National Electric Code (NEC) or Canadian

Electric Code (CEC), and all applicable local codes.

If you are not sure of the proper electrical connections, employ a

competent electrician for the installation. This ensures the installation

complies with all noted electrical codes.

Disconnect power at electrical panel before making any electrical connections. Supply voltage

must be +/- 10% of Inline System nameplate voltage (230 V).

Low or high voltage can damage the Inline System and will void the warranty. Connect pump

to dedicated branch circuit with no other appliances on it.

Do not operate pump unless pump is grounded.

A fused disconnect switch or circuit breaker should be placed at or near the pump as required

by local electrical codes.

Installation Procedure Plumbing

1. Disconnect electrical power at the main breaker.

2. Drain the system (if applicable).

3. Mount the Inline System in the desired location using mounting screws. Screw locations are

shown in FIGURE 1. The Inline System may be installed in any orientation.

s WARNING

WARNING

s WARNING

WARNING

s WARNING

WARNING

s WARNING

CAUTION

s WARNING

CAUTION

Inline Constant Pressure System

4. Install inlet and outlet plumbing and pressure tank as shown in FIGURE 2. A check valve

must be installed in the inlet and outlet plumbing. The outlet check valve should be between

the pump and the pressure tank to prevent the possibility of backow into public water

systems and to ensure proper system operation. The inlet check valve should be used when

no other backow prevention device is present. This inlet check valve should be installed

before the optional bypass loop if that plumbing is used. Franklin Electric recommends that

all system check valves be spring-loaded to provide best system performance. Be sure

to check all local plumbing codes to ensure that all requirements pertaining to backow

prevention are met.

Failure to install check valves properly may prevent the pump

from shutting o. FAILURE TO FOLLOW THIS WARNING may

result in heating of water, personal injury, pump damage, and/or

property damage.

5. Install the pressure sensors at the pressure tank tee downstream of the pressure tank. (The

pressure tank should be between the pressure sensor and the pump.) The pressure sensor

has a 1/4-18 National Pipe Thread (NPT) connection. The pressure sensor should not be

installed in an inverted orientation (upside down). Make sure the pressure sensor and tank

are not located more than 5 feet o the main piping.

6. Install a pressure relief valve downstream of the check valve. The discharge must be

plumbed to a drain rated for maximum pump output at relief pressure setting.

Electrical Diagram

s WARNING

WARNING

WARNINGInline Systems can develop

very high pressure in some

situations. Always install a

pressure relief valve able to

pass full pump flow at 100

psi (6.9 bar). Install the

pressure relief valve near the

pressure tank.

Inline Constant Pressure System

Typical Installation

The Inline System is designed to both increase a system’s incoming pressure and to provide the

system with constant pressure across all outlets. See FIGURE 2 for a graphical representation of

what a typical installation may look like.

*NOTICE: If system plumbing does not have a backow prevention device, a check valve is required on the

incoming water supply line.

NOTE: These optional components are shown in a typical installation diagram. They should be used at the

installer’s discretion as required for particular applications.

MOTOR OVERLOAD PROTECTION NOTE: The drive electronics provide motor overload protection by

preventing motor current from exceeding the maximum Service Factor Amps (SFA). Motor over-temperature

sensing is not provided by the drive.

10.43"

[ 265 ]

7.00"

[177.8 ]

8.00"

[203.2 ]

5.72"

[ 145.2 ]

3.45"

[ 87.7 ]

ACCESS PANEL

ACCESS PANEL SCREWS

9.31"

[ 236.4 ]

2.92"

[ 74.1 ]

6.65"

[ 168.9 ]

1.50"

[38.1 ]

INPUT

POWER

18.84"

[ 478.5 ]

17.32"

[ 439.9 ]

1-1/4" NPT/BSPP

SUCTION 1-1/4" NPT/BSPP

DISCHARGE

Ball

Valve

Check

Valve

Ball

Valve

Union

Coupling

Union

Coupling

To Home

Water Supply

Inline System

Pressure

Shut-o

Switch

(optional)

2 Gallon

Tank

Check

Valve

Power

Ball

Valve

Pressure

Switch

(Discharge into drain

rated for max pump

output at relief pressure)

Pressure

Relief

Valve

Pressure

Gauge

Flow

Optional Bypass

5 feet or Less

*Check

Valve

FIGURE 1:

FIGURE 2:

Otros manuales para Inline 1100

Tabla de contenidos

Idiomas:

Otros manuales de Bomba de agua de Franklin Electric

Franklin Electric

Franklin Electric FACGF Series Manual de usuario

Franklin Electric

Franklin Electric VersaJet Series Manual de usuario

Franklin Electric

Franklin Electric Little GIANT Big John 6-CIM-R Manual de usuario

Franklin Electric

Franklin Electric VR Series Manual de usuario

Franklin Electric

Franklin Electric Little Giant 6EC Series Manual de usuario

Franklin Electric

Franklin Electric Little Giant B-1000 Series Manual de usuario

Franklin Electric

Franklin Electric E-Tech EM Series Manual técnico

Franklin Electric

Franklin Electric Little Giant 1-EA-42 Manual de usuario

Franklin Electric

Franklin Electric FBSTF Series Manual de usuario

Franklin Electric

Franklin Electric C1 SERIES Manual de usuario

Franklin Electric

Franklin Electric LittleGIANT VCMX Series Manual de usuario

Franklin Electric

Franklin Electric Little Giant 558223 Manual de usuario

Franklin Electric

Franklin Electric Little Giant WRS-8E Manual de usuario

Franklin Electric

Franklin Electric little giant s series Manual de usuario

Franklin Electric

Franklin Electric Red Lion RL-50 Manual de usuario

Franklin Electric

Franklin Electric SubDrive NEMA 4 Manual de usuario

Franklin Electric

Franklin Electric 3NC-323P1-184 Manual de usuario

Franklin Electric

Franklin Electric E-Tech Series Manual técnico

Franklin Electric

Franklin Electric VR Series Manual de usuario

Franklin Electric

Franklin Electric Turf Boss FTB3CI Manual de usuario

Franklin Electric

Franklin Electric Submersible Well Pump Manual de usuario

Franklin Electric

Franklin Electric FBSE Series Manual de usuario

Franklin Electric

Franklin Electric VR Spec PAK Manual de usuario

Franklin Electric

Franklin Electric Little Giant VCMX-20 Series Manual de usuario

Manuales populares de Bomba de agua de otras marcas

Neptun

Neptun NPHW 5500 Manual de usuario

Sensidyne

Sensidyne Gilian BDX-II Instrucciones de instalación y funcionamiento

Draper

Draper 47808 Manual de usuario

Trolla

Trolla 12820 Manual de usuario

Sunfab

Sunfab SVH Series Manual de usuario

WilTec

WilTec 50740 Manual de usuario

Fieldmann

Fieldmann FVC 5015 EK Manual de usuario

Everbilt

Everbilt EFSUB5-122HD Manual de usuario

Graco

Graco Husky 3300e Manual de usuario

esotec

esotec 101018 Manual de usuario

moyno

moyno 2000 CC Manual de usuario

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manual de usuario

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guía de solución de problemas

DUROMAX

DUROMAX XP WX Series Manual de usuario

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manual de usuario

Xylem

Xylem e-1532 Series Manual de usuario

Milton Roy

Milton Roy PRIMEROYAL Manual de usuario

STA-RITE

STA-RITE ST33APP Manual de usuario