Framers Corner M3 Manual de usuario
Operators Manual
M3 Manual Underpinner
Only Use Genuine Framers
Corner Universal Wedges
Our Wedges are 10.3mm
Wide, Available In Softwood
And Hardwood Type.
GE ERAL SAFETY RULES
WAR I G: Do not attempt to operate the machine until you have read thoroughly and understood completely all in-
structions, rules, etc. contained in this manual. Failure to comply may result in accidents involving serious personal
injury. Keep this owner's manual and review frequently for continuous safe operation.
1. Know your machine. For your own safety, read the owner's manual carefully. earn its application and limitations,
as well as specific potential hazards pertinent to this machine.
2. Keep guards in place and in working order. If a guard must be removed for maintenance or cleaning, make sure it
is properly replaced before using the machine again.
3. Remove adjusting keys and spanners. Form a habit of checking to see that the keys and adjusting spanners are
removed from the machine before operating it.
4. Keep your work area clean. Cluttered areas and workbenches increase the chance of an accident.
5. Do not use in dangerous environments. Do not use power tools in damp or wet locations, or expose them to rain.
Keep work areas well illuminated.
6. Keep children away. All visitors should be kept a safe distance from the work area.
7. Use the right tools. Do not force the machine or attachments to do a job for which they are not designed. Contact
the manufacturer or distributor if there is any question about the machine's suitability for a particular job.
8. Wear proper apparel. Avoid loose clothing, gloves, ties, rings, bracelets, and jewellery which could get caught in
moving parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair.
9. Always use safety glasses. Normal spectacles only have impact resistant lenses. They are not
safety glasses.
10. Do not over-reach. Keep proper footing and balance at all times.
11. Maintain machine in good condition. Keep machine clean for best and safest performance. Follow instructions for
lubrication and maintenance.
12. Disconnect the machine from power or source (or air supply) before servicing.
13. Do not use any power tools while under the effects of drugs, alcohol or medication.
Page 2
M3 Technical Specification
Moulding Width (Using Rebate Clamp) 0-60mm
Moulding Width (Without Clamp) 0-100mm
Moulding Height 0-100mm
Pin Placement from Back Corner 0-110mm
Wedge Sizes 7 to 15mm
Underpinner Dimensions (WxDxH) 730mm x 800mm x 1110mm
Weight 30kg
Warranty 1 year
Unpacking Your Underpinner
Check the contents have arrived safely and all the components are present according to the list
below.
Page 3
Large Parts
A) Front Stop Bar G) Round Pad
B) Clamp Adjuster H) eft Table
C) Vertical Bar I) Front Clamp
D) Handle J) Right Table
E) Washer K) Rubber Feet x 4
F) Shaped Pad
Small Parts
O) Cap Head Bolt x 8 S) Brass Nipple
P) Washer x 8 T) Magentic Tool
Q) ocking Collar U) Set of Hex Keys
R) ocking Handle
O
P
QR
S
T
U
A B C
D
E
F
G
HIJ
K
ASSEMBLY I STRUCTIO S
1) Fit the Rubber Feet
Screw 4 feet (K) into threaded holes in the base
of the stand. The feet are adjustable in height.
Use a 13mm spanner to tighten the locking nut,
once the machine has been levelled.
2) Assemble the Fence
Unlock two cap head bolts using the Hex key
supplied. Slide the fence forward until the two
round guide bars are flush with the front of the
fence bracket.
Page 4
Top Clamp ock
Fence ock
Front Wedge
Position ock
Rear Wedge
Position ock
Magazine Feeder
Anchor Bolt
Clamp Height
Adjuster
Top Clamp Pad
Front Clamp
Sliding Fence
Main Table
Side Table
MAI FEATURES OF THE M3 U DERPI ER
Fit the Handle and ocking Collar (Q) over the
right hand fence bar.
Insert the Front Stop Bar (A) into the hole in the
fence block.
Place the Brass Nipple (S) into the threaded
hole in the fence block.
Screw in the ocking Handle (R).
3) Assemble the Top Clamp
Fit the Clamp Adjuster (B) onto the bridge and
secure in place with Washer (E) and Handle
(D).
Page 5
Push the adjusting button inwards and insert,
from above, the Vertical Bar (C).
Screw the Shaped Pad (F) onto the end of the
vertical bar.
4) Assemble the Front Clamp
Position the Front Clamp ( ) so that one of the
round holes aligns over the Clamp Pusher.
5) Assemble the Side Tables
Use 8 Cap Head Bolts (O) and Washers (P) to
fit the 2 Side Tables (H&J).
Use a straight edge to set the level of the tables
flush with the main table.
Clamp
Pusher
6) Remove the Footpedal Locking Clamp
For safety during transport the main pedal is
locked down. Undo the handle and slide the
ocking Clamp upwards, allowing the pedal to
move up at the same time.
The ocking clamp can also be used to lock the
footpedal half way down, This reduces the
amount of travel required to insert a wedge and
is sppeds up th epinning operation when
working with small mouldings.
Page 6
OPERATI G I STRUCTIO S
1) Set the Fence
The fence will slide smoothly forward and back.
This allows wedges to be inserted into any
position on the moulding.
The fence is fitted with a limit stop to set the
front wedge position and a limit stop to set the
rear wedge position.
When inserting only one wedge into a corner,
the position should be central.
Front Stop
Fence Lock
Rear Stop
L
1/2 L
When inserting 2 or more wedges into a corner
the first position should be 1/4 distance from the
front edge. The last position should be 1/3rd
distance from the back edge.
There is also a lock to hold the current
position. This is used when ‘stacking’
wedges. Stacking is the process of
inserting multiple wedges in the same
position. The second, and subsequent
wedges, will drive the first wedge deeper
creating a stack.
Using this method 2 x10mm high wedges
will become a 20mm high wedge.
3) Select the Appropriate Sized Wedge
The M3 can use wedge (V-nail) sizes
7mm, 10mm, 12mm and 15mm.
Please ote: Only use
Genuine Framers Corner Universal wedges
10.3mm Width, supplied in glued strips.
Page 7
The warranty will be void if the wrong type
Wedges are use.
There must be a mimumum of 2mm between
the top of the inserted wedge and the face of
the moulding.
4) Load the Magazine
Adjust the height of the wedge magazine using
the round knob located underneath the
magazine.
L
1/4 L
1/3 L
Single
Wedge
Stacked
Wedges
2mm
Minimum
Pull back the nylon cord and hook the looped
end over the anchor bolt.
Insert a strip of wedges, sharpened side up-
wards. When using genuine Framers Corner
Wedges, insert with glued side up.
Unhook the nylon cord and gently let the spring
push the strip of wedges into the magazine.
Use visual observation to confirm that the
wedges slide under the cap with a gap of no
more than 0.5mm.
Page 8
To remove wedges from the magazine, reverse
the proceedure.
Use the Magnetic Tool (T) to pull the partly used
strip of wedges, out of the magazine.
5) Set the Front Clamp
The front clamp grips the moulding by the
rebate. The clamp holds the moulding securely
even when moving from one wedge position to
another. Place a piece of the moulding to be
used against the fence. Press and hold down
the right hand footpedal. The clamp pusher will
travel backwards.
Fit the clamp over the clamp pusher, in such a
way that tip of the clamp is within 15mm of the
moulding.
Release the foot pedal and the clamp will
move forward, gripping the moulding.
The tip of the clamp is desgined to allow
for slight variations in the moulding width.
0.5mm
Gap
Only
15mm
6) Choose the Appropriate Rubber Pad
The pinner is supplied with 2 rubber pads. For
flat moulding the round pad is generally better.
For profiled moulding with varying heights the
shaped pad is generally better.
7) Set the Top Clamp
It is important to set the height of the top clamp
correctly. Place the moulding to be used against
the fence. Set the gap between the lowest point
of the moulding and the underside of the rubber
pad to 20mm. To adjust the height, press the
round button forward to release the vertical bar.
Slide the clamp up or down as required.
Release the clamp adjusting button.
Page 9
8) Insert the Wedge
With all the above settings made:
lPush the fence into the back position
lPress down and hold the right hand pedal
lPlace 2 mitred pieces against the fence
lRelease the right hand pedal
lVisually check the joint is tight
lPress the left hand pedal firmly all the way
........down until the light comes on.
lRelease the left hand pedal
If a second wedge is to be inserted;
Slide the fence and moulding to the next wedge
position and use the left hand footpedal again.
Do not press the right hand pedal until all of the
wedges required have been inserted into the
corner.
During the cycle the top clamp will travel down
and contact the moulding, then the driver will
push one wedge into the underside of the
moulding.
Please note: It is recommended that a suitable
glue is always used when making a frame.
Apply a small amount of glue to one of the
mitred ends before loading into the pinner.
The glue will give the frame strength and
ensure it lasts for many years.
Round
Pad
L Shape
Pad
20mm
Gap
ROUTI E MAI TE A CE
1) Cleaning
Clean any excess glue from around the wedge
exit point.
Clean the top of the table using a silicone spray
or similar product to allow the fence to slide
smoothly.
2) Clearing a blockage
Occasionally, a wedge may get jammed in the
magazine. It may be possible to pull the
wedges out by hand. If it is firmly stuck,
possibly half in and half out, It is highly likely
that the driver will also be stuck in the raised
position.
To clear a blockage; remove the cap, using the
hex key provided. Once removed, the driver
should drop back down and the jammed wedge
can easily be removed.
When refitting the cap, ensure the top is flush
with the surface of the surrounding table.
3) Replacing the Driver
The driver is the part which takes the most wear
and will, one day, need replacing.
ii) Use a hex key to remove the Cap.
iii) Undo the hex bolt which secures the bottom
of the driver to the driver holder.
iv) Push the driver up through the main table
and remove it from the top.
When fitting the new driver ensure the V shape
lip is uppermost, with the point of the V towards
the back of the machine.
Before tightening the hex nut, ensure the driver
is firmly pressed against the bottom of the
holder.
Page 10
4) Changing the Rebate Clamp Cable
i) Remove the 2 Cap Head screws (Part 15)
which hold the Clamp Support Arm (Part 12)
ii) Remove the 2 Cap Head screws (Part 79)
holding the Clamp Cast (Part 62) to the fence.
Drop Clamp Cast down through the machine.
iii) Remove Guide Bar (Part 61) and carefully
remove Clamp Block Spring (Part 82). This will
release the Clamp Block (Part 81) allowing the
Inner Cable to be removed from the Clamp
Bock.
iv) Remove M6 nut (Part 2) on the bottom of the
cable, were the cable passes through the
Clamp Footpedal (Part 33)
v) Remove the M8 nut on the bottom of the
Cable Adjuster (Part 3) where the cable passes
through the bracket on the Floorstand (Part 1).
vi) Remove Inner and Outer Cable from
Floorstand.
vii) Fit the new cable by reversing the
instructions.
viii) Once the cable is replaced, the amount of
movement of the Clamp Block (Part 81) must
be checked. When the footpedal is fully
depressed, the Clamp Block (Part 61) should
move between around 20 mm.
ix) The amount of movement can be adjusted
by the M6 (upper) & M8 (lower) nuts on the
Cable Adjuster (Part 3)
Cap
CE Declaration
We declare that Manual Underpinner,
Model M3 conforms with the following
directives:
Machinery Directive 2006/42/EC
And further conforms with the following EU
harmonized standard;
EN ISO 12100:2010
The equipment named above has been
tested and found to comply with the
relevant sections of the above referenced
specification. The machinery complies with
all essential requirements of the directive.
A copy of the declaration is available
by contacting framers corner.
Tabla de contenidos
Otros manuales de Herramientas de Framers Corner
