Foxtech T30s Manual de usuario
- 2 -
Catalog
1. Disclaimer........................................................................................- 4 -
2. Product Precautions....................................................................... - 4 -
2.1. Installation Note.................................................................. - 5 -
2.2. Precautions for Use............................................................. - 5 -
3. Product Introduction......................................................................- 5 -
3.1. Item List (V20: 5km grade )................................................- 6 -
3.2. Item list (V30: 15km grade)................................................- 7 -
4. Product Instruction........................................................................ - 8 -
4.1. T30S main components name............................................ - 8 -
4.2. V20 Airborne Unit Indicator&Interface Instruction......... - 9 -
4.3. V20 Receiver Installation and Connection...................... - 10 -
4.4. V30 Airborne Unit Indicator&Interface Instruction....... - 12 -
4.5. V30 Receiver Installation and Connection...................... - 13 -
5. T30S Second Display Instruction................................................ - 14 -
5.1. Touch calibration on the secondary screen.................... - 14 -
5.2. Split-Screen Setting........................................................... - 15 -
6. Remote Controller Operation...................................................... - 15 -
6.1. Power-on and Power-off of the Remote Controller and
Computer...................................................................................- 15 -
6.2. Remote Controller & Receiver Indicator Instruction..... - 17 -
6.2.1. Remote Controller Indicator Instruction..............- 17 -
6.2.2. V20 Receiver Indicator Instruction.......................- 18 -
6.2.3. V30 Receiver Indicator Instruction.......................- 18 -
6.3. Remote Controller Antenna.............................................. - 19 -
7. The Use of Parameters Setting Software of Remote Controller- 19 -
7.1. Parameters Setting Software Instruction........................ - 19 -
7.2. Channel monitoring and calibration................................ - 20 -
7.3. Channel Configuration...................................................... - 21 -
7.4. Fail-safe Setting..................................................................- 24 -
7.5. Channel Hold...................................................................... - 25 -
7.6. Throttle Hold......................................................................- 26 -
7.7. Alarm Instructions for remote control............................ - 27 -
7.8. Charge the Remote Controller.......................................... - 28 -
- 3 -
8. V20 Video&Data Transmission Module Operation....................- 28 -
8.1. V20 Connection Instruction..............................................- 28 -
8.2. V20 Video&Data link Serial Port Operation.................... - 29 -
8.3. V20 LAN Port..................................................................... - 31 -
8.4. Fast Reset and Configuration of Video Transmission
Module....................................................................................... - 33 -
8.4.1. Fast Reset of Video Transmission Module........... - 33 -
8.4.2. Fast Configuration of Video Transmission Receiver- 33 -
8.4.3. Fast Configuration of Video Transmission Module of
RC....................................................................................... - 37 -
9. V30 Video&Data Transmission Module Operation....................- 39 -
9.1. Video Connection Instruction for HDMI Version............ - 40 -
9.2. Video Connection Instruction for LAN Version...............- 41 -
9.3. Display the Video in Mission Planner.............................. - 43 -
9.4. Display image in QGC........................................................ - 45 -
10. V30 Parameters Setting............................................................. - 46 -
10.1. Connecting the device..................................................... - 46 -
10.2. Command Configuration List..........................................- 48 -
10.3. V20 Video&Data Transmission Module Parameters.... - 50 -
10.4. V30 Video&Data Transmission Module Parameters.... - 51 -
10.5. T30s Remote Controller Port Instruction..................... - 51 -
11. Firmware Upgrading Procedure............................................... - 54 -
11.1. HID Controller..................................................................- 54 -
11.2. T30S Remote Controller Firmware Upgrading.............- 57 -
11.3. V20 Receiver Firmware Upgrading............................... - 58 -
12. Common Questions.................................................................... - 59 -
13. T30S Remote Controller Parameters........................................- 59 -
- 4 -
1. Disclaimer
Thank you for purchasing the T30S hand-held ground control station. Please use it in
accordance with the local radio control regulations and read this statement carefully
before using it. Once used, it shall be deemed to endorse and accept all contents of this
statement. Please strictly follow this instruction to install and use the product. The
supplier will not bear any legal liability for any result or loss caused by improper use,
installation, final assembly or modification of the product.
2. Product Precautions
1) T30s, the ground terminal (hereinafter referred to as ground unit) is used with the
airborne unit (hereinafter referred to as airborne unit).
2) T30s has different versions based on the different data link.
✱If with only data link, the matched airborne end is R20.
✱If with video&data link, the matched airborne ends are V20 and V30.
V20: 5km grade module, frequency band: 2.3GHz/2.4GHz/2.5GHz;
V30: 15km grade module, frequency band: 800MHz/1.4GHz
3) The ground unit has a built-in 12V battery (lithium battery 3s), the airborne unit needs
external power supply input DC7.4-12V (lithium battery 2s-3s), please follow the
specification to power the radio.
4) If you use it improperly, the aircraft may cause some degree of injury and damage to
people and property, please pay attention to safety when using.
5) In order to serve our customers better, our R & D team has been upgrading and
optimizing our products, the corresponding software and firmware will be updated from
time to time, there may be incompatibility between different firmware versions of the
ground unit and airborne unit, so please remember to check the software firmware
version when using. For more information, pls refer to our website for the latest firmware
and technical support.
6) Example of basic software firmware version: Parameters setting software:
HZY_ToolBench V1.2.3.4; Ground unit firmware: TTx30-1.2.3-1.0; Airborne unit V20
firmware: V20RX-1.2.3-1.00; Airborne end V30 firmware: V30RX-1.2.3-1.0.
- 5 -
7) The software, firmware, drivers, port conversion tools, etc. will be updated from time
to time on our website, please visit our website to download, or contact customer service
staff to obtain them.
8) If you encounter any problem during the installation or use , please contact us
2.1. Installation Note
1) Be sure to use the spare parts provided by our company.
2) Be sure to install the antennas before power on to avoid damage to the circuit.
3) Try to make the receiver antenna without obstruction, and the end part of the antenna
is vertically downward without bending, so as to avoid shortening the communication
distance or even failing to communicate due to obstruction.
4) Do not disassemble or refit without permission. If you encounter any problem that
cannot be solved during installation, please contact us directly.
5) During installation, keep proper distance between electronic devices to minimize
electromagnetic interference.
2.2. Precautions for Use
1) Before use, please make sure that all connection wires are fastened reliably and all
parts work normally.
2) Please open the configuration software of the remote control and check whether the
channels are normal after power-on.
3) Please check the surrounding environment to ensure that there is no interference from
other devices, otherwise T30s data transmission performance will be seriously affected.
4) Ensure that the antennas are free from obstacles and bends during use, and stay away
from large metal structural parts as far as possible to avoid communication obstruction.
5) Check the power of the remote control before use. If the parameter adjustment
software shows that power is low, please charge the remote control timely. If the remote
control is turned off, the receiver has entered the state of out-of-control protection. Stop
using it when the battery is too low. Don't rely on the device's low-power alarm, which is
only a precaution and tells you when to charge. It takes about 5-6hs to be fully charged.
3. Product Introduction
T30s is a hand-held ground control station that integrates remote control, data
transmission and ground station.
T30s is highly integrated, small size, easy operation, multichannel adjustable, dual S-BUS
outputs and so on.
Compared with the last generation, the computer performance configuration has been
greatly improved, and the remote-control circuit design is optimized.
- 6 -
The channel number has increased from 16 to 23, and the anti-interference of data
transmission and power supplies have also been optimized. Dual S-BUS can be mapped
randomly in 8 analog channels, 4 three-position switches, and 11 buttons.
Multi frequency can be chosen between 840MHz, 915MHz, 1.4GHz, and 2.3-2.5GHz. Stable
data transmission can be provided at distances of 3-30km based on different data link
versions and application environment. It can be widely used in the field of control and
data transmission for industrial drones.
3.1. Item List (V20: 5km grade )
T30s remote controller
×
1 V20 receiver x 1
TNC 2.3G ZYJB antenna
×
2 SMA 2.3GZYJB antenna
×
2
T30S transmitting terminal V20 receiving terminal
Power
supply
cable*1
Charger*1 Receiver upgrade
configuration line*1
Lan-to-4 pins
line*1
Power for receiver
(DC:7.4-12V, Li
battery 2s-3s)
Charge for
remote control
Used for firmware
upgrading
and parameters
Setting for receiver
For module
Parameter
configuration
- 7 -
3.2. Item list (V30: 10km grade)
Accessories
Charger×1 Wire
Power for remote controller
1、power plug XT30 power cable * 1
2、SBUS, TTL signal wire GH 3pin * 3
T30s remote controller
×1 V30 receiver
x 1
TNC 1430-1444MHz ZYJB antenna×2
SMA
1430-1444MHz ZYJB antenna×1
HDMI version LAN Version
HDMI A to micro LAN to GH 4pin *
1
- 8 -
4. Product Instruction
4.1. T30S main components name
①T30S secondary display: Used for extended display of host video
②Left and right rockers: corresponding T1, T2, T3 and T4, used for flight control
③Four three-position switches: corresponding SA, SB, SD, SE
- 9 -
④Left and right rotary knobs: corresponding LD and RD
⑤Two buttons(or three-position switches): corresponding S1, S2 (or SC, SF)
⑥9 key channels: corresponding F1~F9
⑦Power button and indicator: used for power on and power off the device
⑧Power, signal strength, transmitting and receiving indicator: used for indicating power,
working status
⑨Left and right deflector rods: corresponding T5 and T6(return to center mode)
⑩RF antenna interfaces*2: used for connecting RF antennas
⑪Audio input and output interface: connecting headset audio output or microphone audio
input
⑫LAN port
⑬USB interface: 2*USB 3.0
⑭Multimedia interface: HDMI HD video and audio transmitting interface
⑮Video transmission interface: VGA HD video transmission interface
⑯Secondary display HDMI video input: can be used for external extended video input
⑰TYPE-C interface 1: user for power and touch for the secondary screen
⑱TYPE-C interface 2: user for the secondary display backup power
⑲Charging interface: connecting 12.6V DC adapter
⑳External battery charging interface: used for external battery extension
4.2. V20 Airborne Unit Indicator&Interface Instruction
Front view
①Video transmission CPU indicator: light will be continuously ON in normal working
condition.
②Data receiving indicator: light will flicker in the condition of data receiving.
- 10 -
③Date transmitting indicator: light will flicker in the condition of data transmitting.
④Signal strength indicator: S3 ON, signal is weak; S3 and S2 ON, signal is moderate; S3, S2
and S1 ON, signal is strong.
⑤Key switch: used for firmware upgrading, out-of-control protection settings, restore the
default transmission settings.
Side view
①LAN port: used for video transmission or getting video transmission parameters.
②LAN indicator: After connecting LAN port, indicator will flicker.
③TTL port: full duplex serial port
④S-Bus port: dual S-Bus output
⑤S-Bus1 data indicator: indicator will flicker when there is data transmitting and
receiving of S-Bus1.
⑥Power supply port: 7.4-12v.
⑦S-Bus2 data indicator: indicator will flicker when there is data transmitting and
receiving of S-Bus2.
⑧WAN connection indicator: indicator will flicker when connecting WAN port.
⑨Video transmission WAN port: used to connect to an external network or the Internet.
By default, the S-BUS1 and S-BUS2 interfaces output the CH1 to CH16 of the remote
control to 1-16 channels.
4.3. V20 Receiver Installation and Connection
1. Connecting antennas to SMA port of V20.
2. Fix the receiver to the appropriate position of the aircraft by using double-sided tape.
Tabla de contenidos
Otros manuales de Mando a distancia de Foxtech
