Fostex FD-8 Manual de usuario

FD-8 Owner’s Manual Supplement

<NOTE>: When formatting a large capacity hard disk, the time required to format will be in

relation to disk size. As a general estimate, it requires about 15 minutes to format 1GB and

thus, as an example, it will take about 7 hours for a 30GB hard disk.

The functions explained here have been added to the FD-8 subsequent to version

1.10 because of a version up of the software. Prior to operating the FD-8, please

read this supplement together with the main manual.

1. Large capacity hard disks can now be used.

It is now possible to use a 2.5 inch E-IDE hard disk with a capacity up to about 30GB

(FS=44.1kHz) for the FD-8 internal current drive disk.

2. In the BAR/BEAT/CLK (bar/beat/clock) time base, the offset figure of the BAR

that indicates the head of the disk can now be edited.

Although [Time Base] is explained in [Before Operating] in the main owners manual, for

the unit representing the present traveling position of the FD-8, MTC (MIDI time code) or

BAR/BEAT/CLK are employed in addition to ABS (absolute time). For this reason, the

figure indicating the present disk position will be different depending on the selected

time base.

With the FD-8 in the initial setup state, when the disk is at the head position (ABS 00M

00S 00F) the MTC offset indication will be [MTC 00H 59M 57S 00F], and when by BAR/

BEAT/CLK it will be [-002BAR 1BEAT 00CLK].

Before this version up, changing the offset figure was limited to MTC and the BAR/BEAT/

CLK offset figure was fixed to [-002BAR 1BEAT 00CLK]. But after this version up, the BAR

offset figure of BAR/BEAT/CLK can now be changed and set to any figure within a range

of -002 ~ -009.

The FD-8’s initial state [-002BAR 1BEAT 00CLK] will always be displayed and the BAR

offset figure will be [-002BAR].

In order to set the offset figure of the BAR/BEAT/CLK display, use the SETUP mode of the

FD-8 in the same manner for setup of MTC offset. For procedures, refer to the reverse

side explanation. For setup of MTC offset, please refer to [SETUP mode] of the main

owners manual.

1. Preselect the program to which offset is to be setup.

The following example shows in the display that

program 2 have been selected.

2. Switch to the SETUP mode by pressing the SETUP

key.

In the initial setup, the [Sign. Set?] menu will be

displayed (If a different menu is displayed, rotate the

JOG dial to display the [Sign. Set?] menu.).

3. Then press the EXECUTE/YES key.

The display will change to [Sign. Chk] and the

presently set beat will be shown. In the initial setup,

the display will show that the first bar is set to 4/4

beat.

4. Rotate the JOG dial counter-clockwise.

The offset figure of the presently set bar is displayed

and in the initial setup, [-002BAR OFFSET] will be

displayed as shown below.

5. Press the EXECUTE/YES key.

Simultaneous with entering [Sign. Edit] mode, [2] of

-002BAR will blink and the BAR offset figure can then

be editied.

6. Enter the desired offset figure by rotating the JOG

dial, and then press the EXECUTE/YES key.

Any offset figure in the range of 2~9 can be input

(Example below show that [5] had been entered for

the BAR figure.). When the EXECUTE/YES key is

pressed after input of the above number, the offset

figure thus input will be setup and the display will

change to the [Sign. Set?] menu.

7. Exit from the SETUP mode by pressing the EXIT/NO

key.

Setup procedures for BAR/BEAT/CLK offset

<NOTE>: Offset setups can be executed for each program. The setup content will be

maintained even though power is switched off.

FOSTEX CORPORATION

3-2-35, Musashino, Akishima-shi,Tokyo 196-0021, Japan

FOSTEX CORPORATION OF AMERICA

15431, Blackburn Ave., Norwalk, CA 90650, U.S.A.

Blink

PRINTED IN JAPAN AUG.1999 8288 677 000 FX.

CLK

SYNC OUT DRIVESCSI

AUTO A.PUNCH

SETUP

BAR

44.1kHz

EXECUTE

/YES

EXECUTE

/YES

CLK

SYNC OUT DRIVESCSI

AUTO A.PUNCH

SETUP

BAR

44.1kHz

SETUP

DRIVE

AUTO A.PUNCH

SYNC OUT

CLK SCSI

BAR

44.1kHz

CLK

SYNC OUT DRIVESCSI

AUTO A.PUNCH

SETUP

BAR

44.1kHz

EXECUTE

/YES

SETUP

DRIVE

AUTO A.PUNCH

SYNC OUT

CLK SCSI

BAR

44.1kHz

CLK

SYNC OUT DRIVESCSI

AUTO A.PUNCH

SMF

PGM

ABS

44.1kHz

CLK

SYNC OUT DRIVESCSI

AUTO A.PUNCH

SMF

PGM

ABS

44.1kHz

SETUP

DRIVE

AUTO A.PUNCH

SYNC OUT

CLK SCSI

44.1kHz

SETUP

DRIVE

AUTO A.PUNCH

SYNC OUT

CLK SCSI

44.1kHz

SETUP

DRIVE

AUTO A.PUNCH

SYNC OUT

CLK SCSI

44.1kHz

SETUP

Otros manuales para FD-8

Tabla de contenidos

Otros manuales de Equipo de grabación de Fostex

Fostex

Fostex DMT-8VL Manual de usuario

Fostex

Fostex VF-16 Manual de usuario

Fostex

Fostex 80 Manual de usuario

Fostex

Fostex VR800 Guía del usuario

Fostex

Fostex X-34 Manual de usuario

Fostex

Fostex D-160 Manual de usuario

Fostex

Fostex DV-824 Manual de usuario

Fostex

Fostex DE-1 Manual de usuario

Fostex

Fostex ATC-4 Manual de usuario

Fostex

Fostex A-4 Manual de usuario

Fostex

Fostex VF80EX Manual de usuario

Fostex

Fostex E-16 Manual de usuario

Fostex

Fostex X-28H Manual de usuario

Fostex

Fostex D-90 Manual de usuario

Fostex

Fostex CR200 Manual de usuario

Fostex

Fostex VF160EX Manual de usuario

Fostex

Fostex X-55 Manual de usuario

Fostex

Fostex D-160 Instrucciones de instalación y funcionamiento

Fostex

Fostex 5040 Manual de usuario

Fostex

Fostex FR-2 Manual de usuario

Fostex

Fostex MR-16HD Manual de usuario

Fostex

Fostex FR-2 Manual técnico

Fostex

Fostex XR-7 Manual de usuario

Fostex

Fostex PD-4 Manual de usuario

Manuales populares de Equipo de grabación de otras marcas

KV2 Audio

KV2 Audio 500 Series Manual de usuario

Robotics Technologies

Robotics Technologies microBus-Cam II Manual de usuario

Seca

Seca 460 Manual de usuario

Cognex

Cognex MVS-8000 Series Manual de usuario

Mect

Mect MPNC006 Series Manual de usuario

Bad Caf

Bad Caf THE LEASH Manual de usuario

Strymon

Strymon NIGHTSKY Manual de usuario

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manual de usuario

Tews Technologies

Tews Technologies TPMC465 Manual de usuario

Honeywell

Honeywell Excel 50 Manual de usuario

SeaLevel

SeaLevel COMM+8.LPCI Manual de usuario

Arturia

Arturia AUDIOFUSE STUDIO Manual de usuario

Rukra

Rukra RK-1240 Manual de usuario

Samson

Samson SCOM Manual de usuario

Dynacord

Dynacord DPS260 Manual de usuario

Nice

Nice Core Manual de usuario

Pyle Pro

Pyle Pro PSS8 Manual de usuario

RF-System

RF-System TinyGate Manual de uso y cuidado