FOS Technologies 150W LED Spot Manual de usuario

150W LED Spot

User Manual

PLEASE KEEP THIS MANUAL FOR FUTURE NEEDS

1. Unpacking

Thank you for choosing our products. For your own safety, please read this

manual before installing the device. This manual covers the important information on

installation and applications. Please install and operate the fixture with following

instructions, make sure the power is off before opening the light or repairing.

Meanwhile, please keep this manual well for future needs.

It is made of a new type of high temperature strength of engineering plastics

and cast aluminum casing with nice outlook. The fixture is designed and manufactured

strictly following CE standards, complying with international standard DMX512 protocol.

It’s available independently controlled and linkable with each other for operation. And it

is applicable for large-scale live performances, theater, studio, nightclubs and discos.

150W spot pro fixture which features high brightness and stability. Please carefully

unpack it when you receive the fixture and check whether it is damaged during the

transportation. And please check whether the following items are included inside the

box:

Moving head--------One DMX signal cable-------One

Power cable--------One User manual---------------One

Omega bracket----Two Safety cable-------------One

1/ 10

2. Safety Instructions

This device has

left the factory in perfect condition. In order to maintain this

condition and to ensure a safe operation, it is absolutely necessary for the user to

follow the safety instructions and warning notes written in this user manual.

If the device has been exp

osed to temperature changes due to environmental

changes, do not switch it on immediately. The arising condensation could damage

the device. Leave the device switched off until it has reached room temperature.

This device falls under protection-class I. Therefore it is essential that the device be

earthed.

The electric connection must carry out by qualified person.

The device shall only be used with rate voltage and frequency.

Make sure that the available voltage is not higher than stated at the end of this

manual.

Make sure the power cord is never crimped or damaged by sharp edges. If this

would be the case, replacement of the cable must be done by an authorized dealer.

Always disconnect from the mains, when the device is not in use or before cleaning

it. Only handle the power cord by the plug. Never pull out the plug by tugging the

power cord.

During initial start-up some smoke or smell may arise. This is a normal process and

does not necessarily mean that the device is defective, it should decrease

gradually.

Please don't project the beam onto combustible substances.

Fixtures cannot be installed on combustible substances, keep more than 50cm

distance with wall for smooth air flow, so there should be no shelter for fans and

ventilation for heat radiation.

the external flexible cable or cord of this luminaire is damaged, it shall

exclusively replaced by the manufacturer or his service agent or a similar

qualified person in order to avoid a hazard.

2/ 10

3. Key Features

Voltage: AC100-240V,50-60Hz

Power: 250W

Led source: 150W White LED

Color Temperature: 7500K-8000K

Led Life Time: 50000 Hours

Channel: 15 DMX channel

Control: DMX/Master-slave/Auto/Sound activated

Pan: 540 degree + fine Tilt: 270 degree + fine

Dimmer: 0-100% smooth linear dimmer

Strobe: 1-25 Hz with pulse effect

Color Wheel: 8 colors + open, with rainbow effect

Static Gobo Wheel: 7 gobos + open, with rotation and running water effect

Rotation gobo wheel: 7 gobos+open

Prism: 8 facet round prism+6 facet linear prism+frost filter

Frost: With frost effect

Screen: Colorful screen with Chinese and English, can adjust 180 degree to fit

different installation position

3/ 10

4. Operation Instructions

-The moving head is for spot purpose.

-Don’t turn on the fixture if it’s been through severe temperature difference like after

transportation because it might damage the light due to the environment changes.

So make sure to operate the fixture until it is in normal temperature.

-This light should be keep away from strong shaking during any transportation or

movement.

-Don’t pull up the light by only the hea

d, or it might cause damages to the

mechanical parts.

-Don’t expose the fixture in overheat, moisture or environment with too much dust

when installing it. And don’t lay any power cables on the floor. Or it might cause

electronic shock to the people.

-Make sure the installation place is in good safety condition before installing the

fixture.

Make sure to put the safety chain and check whether the screws are screwed

properly when installing the fixture.

-Make sure the lens are in good condition. It’s recommended to replace the units if

there are any damages or severe scratch.

-Make sure the fixture is operated by qualified personnel who knows the fixture

before using.

-Keep the original packages if any second shipment is needed.

-Don’t try to change the fixtures without any instruction by the manufacturer or the

appointed repairing agencies.

-It is not in warranty range if there are any malfunctions from not following the user

manual to operate or any illegal operation, like shock short circuit, electronic shock,

lamp broke, etc.

5. Mounting and Installation

Cautions: For added protection mount the fixtures in areas outside walking paths,

seating areas, or in areas were the fixture might

be reached by unauthorized

personnel.

Before mounting the fixture to any surface, make sure that the installation area can

hold a minimum point load of 10 times the device’s weight.

Fixture installation must always be secured with a secondary safety attachment,

such as an appropriate safety cable.

4/ 10

Never stand directly below the device when mounting, removing, or servicing the

fixture from a

periodic safety inspection of all installation material and the fixture. If you lack these

qualification

s, do not attempt the installation yourself. Improper installation can

result in bodily injury.

Be sure to complete all rigging and installation procedures before connecting the

main power cord to the appropriate wall outlet.

Clamp Mounting: The beam spot wash 3-in-1 provides a unique mounting bracket

assembly that integrates the bottom of the base, the included “Omega Bracket,” and

the safety cable rigging point in one unit (see the illustration below). When mounting

this fixture to truss be sure to secure an appropriately rated clamp to the included

omega bracket using a M10 screw fitted through the center hole of the “omega

bracket”. As an added safety measure be sure to attached at least one properly

rated safety cable to the fixture using on of the safety cable rigging point integrated

in the base assembly

Regardless of the rigging option you choose for your 10R, always be sure to secure

your fixture with a safety cable. The fixture provides a built-in rigging point for a

safety cable on the hanging bracket as illustrated above. Be sure to only use the

designated rigging point for the safety cable and never secure a safety cable to a

carrying handle.

5/ 10

6. DMX-512 control connections

Connect the provided XLR cable to the female 3-pin XLR output of your controller and

the other side to the male 3-pin XLR input of the moving head. You can chain multiple

Moving heads be connected together through serial linking. The cable needed should be

two core, screened cable with XLR input and output connectors

. Please refer to the

diagram below.

DMX-512 connection with DMX terminator

For installations where the DMX cable has to run a long distance or is in an electrically

noisy environment, such as in a discotheque, it is recommended to use a DMX

terminator. This helps in preventing corruption of the digital control signal by electrical

noise. The DMX terminator is simply an XLR plug with a 120 Ω resistor connected

between pins 2 and 3,which is then plugged into the output XLR socket of the last fixture

in the chain. Please see illustrations below.

PIN 3

PIN 2

120Ω

6/ 10

7. Display menu control

Address 1-512

Chinese

English

PanReverse

Lang Set

DisplayRev

Backlight

TiltReverse

Sound Sense

Reset All

Yes

LED On

Off(30S)

Yes

0-80%

Yes

Temp

Protection

Motor

Correction

Motor

Reposition

Factory Reset

Version

Err Info

Off at

lamp xx

0-255

SYS Set

Advan

Manual

Info

Language setting

Display turn up 180

degree setting

Display backlight

setting

Pan Reverse

setting

Tilt reverse

setting

Sound sensentive

Reset

Do not change

the data unless

it’s necessary

Manual control of

each channel

UseMode

Channel Mode

User Mode

Channel Edit

No DMX Mode

Auto prog

Sound prog

Music

Scene

Alone

Maste

Alone

Maste

Set the LED

protection

temperature

Software version

Error information

Clear

Auto

Keep

Your edited channel

Sequence mode

Edit the channel sequence

of User mode

Standard Channel mode

Standard

7/ 10

8. DMX Channels

18 Channel Mode

Function

DMX Value

Details

Pan

0-255

Pan movement

Pan fine

0-255

Pan fine

Tilt

0-255

Tilt movement

Tilt fine

0-255

Tilt fine

Pan/Tilt Speed

0-255

Pan/Tilt speed control from fast to slow

Dimmer

0-255

0-100% Dimmer

7 Strobe

0-15

No function

16-95

Strobe from slow to fast

96-175

Pulse strobe from slow to fast

176-249↑

Random strobe from fast to slow

250-255↑

Open

8 Color wheel

0-4

All white round

5-9

Open mixed with color 1

10-14

Color 1

15-19

Color 1 mixed with color 2

……

………………

80-84

Color 8

85-89

Color 8 mixed with open

90-174

Color wheel colockwise rotation from fast to slow

175-255

Color wheel anti-clockwise rotation from slow to fast

9 Static gobo wheel

0-9

Open

10-19

Static Gobo 1

20-29

Static Gobo 2

……

………………

70-79

Static Gobo 7

80-124

Gobo wheel clockwise rotation from fast to slow

125-129

Stop(stop to open)

130-174

Gobo wheel anti-clockwise rotation from slow to fast

175-234

Gobo shock slow to fast(Each 10 DMX value is a gobo)

235-255

7th Gobo shake from slow to fast

10 Rotation gobo wheel

0-9

Open

10-19

Rotation Gobo 1

20-29

Rotation Gobo 2

……

………………

70-79

Rotation Gobo 7

80-124

Gobo wheel clockwise rotation from fast to slow

125-129

Stop(stop to open)

130-174

Gobo wheel anti-clockwise rotation from slow to fast

175-234

1th to 6th Gobo shock slow to fast(Each 10 DMX value is a gobo)

235-255

7th Gobo shake from slow to fast

11 Rotaion gobo rotates

0-127

Change position

128-191

Clockwise continious rotation from fast to slow

192-255

Anti-Clockwise continious rotation from slow to fast

12 Prism 0-255 0-49 no function,50-99 is 8-facet round prism, 100-149 is 6 facet

linear prism,150-255 is frost effect

13 Facet prism rotation

0-127

Change position

128-191

Clockwise cotinious rotation from fast to slow

192-255

Anti-colokwise continious rotation from slow to fast

Focus

0-255

Focus

Reset&Macro funtion

0-255

0-80 No function, 80-240 Built-in program, 241-255 Reset

8/ 10

9. Maintenance and Cleaning

The following points have to be considered during the inspection:

1. All screws for installing the devices or parts of the device have to be tightly connected

and must not be corroded.

There must not be any deformations on the housing, color lenses, fixations and

installation spots (ceiling, suspension, trussing).

3. Mechanically moved parts must not show any traces of wearing and must not rotate

with unbalances.

4. The electric power supply cables must not show any damage, material fatigue or

sediments.

Further instructions depending on the installation spot and usage have to be adhered by

a skilled installer and any safety problems have to be removed.

In order to make the lights in good condition and extend the life time, we suggest a

regular cleaning to the lights.

1) Clean the inside and outside lens each week to avoid the weakneness of the lights

due to accumulation of dust.

2) Clean the fan each week.

3) A detailed electric check by approved electrical engineer each three month, make

sure that the circuit contacts are in good condition, prevent the poor contact of circuit

from overheating.

We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth.

Never use alcohol or solvents.There are no serviceable parts inside the device. Please

refer to the instructions under “Installation instructions”.Should you need any spare parts,

please order genuine parts from your local dealer

9/ 10

Tabla de contenidos

Otros manuales de Equipo de DJ de FOS Technologies

FOS Technologies

FOS Technologies FOS Spot 150W Manual de usuario

FOS Technologies

FOS Technologies FOS Ultra Par Manual de usuario

FOS Technologies

FOS Technologies Roller 7R Manual de usuario

FOS Technologies

FOS Technologies SuperStorm L006796 Manual de usuario

FOS Technologies

FOS Technologies FOS Spot 40W Manual de usuario

FOS Technologies

FOS Technologies FOS 20W RGB Manual de usuario

FOS Technologies

FOS Technologies PAR COB 200W LED TW Manual de usuario

FOS Technologies

FOS Technologies L004503 Manual de usuario

FOS Technologies

FOS Technologies FOS 12R Hybrid Manual de usuario

FOS Technologies

FOS Technologies FOS ACL Line 12 Manual de usuario

FOS Technologies

FOS Technologies FOS HYDRO BSW Manual de usuario

FOS Technologies

FOS Technologies Wash 360 LED Manual de usuario

FOS Technologies

FOS Technologies ZOOM 2825 Manual de usuario

FOS Technologies

FOS Technologies FOS Wash LED Quad II Manual de usuario

FOS Technologies

FOS Technologies FOS BEAM IP Manual de usuario

FOS Technologies

FOS Technologies A10-FB4 Manual de usuario

FOS Technologies

FOS Technologies 12R Hybrid PRO Manual de usuario

FOS Technologies

FOS Technologies PAR 18x12W PRO Manual de usuario

FOS Technologies

FOS Technologies FOS PAR 7x15 6 in 1 Manual de usuario

FOS Technologies

FOS Technologies FOS 12R Hybrid Manual de usuario

FOS Technologies

FOS Technologies TOURING PAR IP HEX Manual de usuario

FOS Technologies

FOS Technologies Luminus Manual de usuario

FOS Technologies

FOS Technologies Co2 LED DMX Manual de usuario

FOS Technologies

FOS Technologies Wash LED Quad III Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario