Fortessa 3800-F Manual de usuario

SAFETY NOTES

Please read this manual carefully before attempting to install or operate the Access Control

equipment.

This equipment must be installed in line with all relevant regulations and standards.

Make sure that wiring is rated according to fuses and current limits of relevant power supplies.

All connections to this unit must be SELV level. (Safety Extra Low Voltage, BS EN 60950 1992)

Every effort is made to ensure that this manual is complete and free from errors. However we

reserve the right to make changes to these products and this manual without notice.

No liability is accepted for loss damage or injury as a consequence of using these products or

instructions.

These products are not designed for use in life support or safety critical appliances or systems

where malfunction of these products can reasonably be expected to result in personal injury.

Customers using or selling these products for use in such applications do so at their own risk

EMC, LV and

RTTE

Certificate Number 17851

Document Number: 3802-I01 Issue 05

HARDWARE MANUAL

Contents

Contents__________________________________________________________2

System Overview _________________________________________________1

FORTESSA Controller_____________________________________________2

Description _____________________________________________________________2

Box Contents ____________________________________________________________2

Mounting _______________________________________________________________2

Lock Drive______________________________________________________________3

Readers ________________________________________________________________3

Inputs__________________________________________________________________3

Resetting to Factory Defaults _______________________________________________3

Supply _________________________________________________________________3

Network________________________________________________________________3

Cable __________________________________________________________________3

Network______________________________________________________________3

Reader _______________________________________________________________4

LEDs __________________________________________________________________4

Status________________________________________________________________4

Reader (A & B) ________________________________________________________4

Network LEDS ________________________________________________________4

Relay ________________________________________________________________4

Fire__________________________________________________________________4

Intruder ______________________________________________________________4

Notes on the Fire and Intruder Short Circuit Detector LEDs________________________4

FORTESSA Reader (Switch Plate Style)_____________________________5

Box Contents ____________________________________________________________5

Description _____________________________________________________________5

Power__________________________________________________________________5

Mounting _______________________________________________________________6

Connections_____________________________________________________________6

Inputs__________________________________________________________________6

Door Sensor___________________________________________________________6

Request to Exit_________________________________________________________6

Locking Device ________________________________________________________6

LEDs __________________________________________________________________7

FORTESSA Reader (Mullion Style) _________________________________8

Box Contents ____________________________________________________________8

Description _____________________________________________________________8

Mounting _______________________________________________________________8

FORTESSA Touch Switch _________________________________________9

Description _____________________________________________________________9

Box Contents ____________________________________________________________9

Power_________________________________________________________________10

Mounting ______________________________________________________________10

Connections____________________________________________________________10

LED ________________________________________________________________10

BUZ________________________________________________________________10

CONTACT __________________________________________________________11

LED’s ________________________________________________________________11

FORTESSA USB Interface ________________________________________13

Description ____________________________________________________________13

Box Contents ___________________________________________________________13

Mounting ______________________________________________________________13

Connections____________________________________________________________13

Cables ________________________________________________________________14

Desktop Reader _________________________________________________________14

LED Indicators _________________________________________________________14

The Reader LEDs _____________________________________________________14

The USB LEDs _______________________________________________________14

The FORTESSA Network LEDs__________________________________________14

FORTESSA Credentials __________________________________________16

Proximity Card _________________________________________________________16

Proximity Key Fob ______________________________________________________16

Proximity Sticky Dot_____________________________________________________16

FORTESSA Product Codes _______________________________________16

FORTESSA.net __________________________________________________17

Programming___________________________________________________________17

Keyboard ____________________________________________________________17

Functions ____________________________________________________________18

Set FORTESSA.net IP Address___________________________________________18

Set Server IP Address Filter (Optional)_____________________________________18

Controller / Door Name Table _____________________________________18

System Overview

Figure 1

FORTESSA Controller

Description

The FORTESSA and FORTESSA.net Controllers are single door controllers for use

with the FORTESSA access control range. FORTESSA uses a revolutionary reader

interface that allows most door functions to be handled over a single 4 core

unscreened cable. The controller is completely programmed from a PC using the

Doors Express software.

Figure 2

Box Contents

1 x FORTESSA Controller or FORTESSA.net Controller mounted in a 165mm

x 145mm steel enclosure (black)

1 x Hardware Manual

Mounting

The FORTESSA Controller and its power supply should be mounted in a secure

location or on the secure side of the door. This should ideally be as close to the door

as possible (Max 100m cable run) to avoid volt drops.

Lock Drive

There are two voltage free relays (A & B) on the FORTESSA Controller for operating

locking devices.

Readers

The controller has 2 proximity reader channels for use with FORTESSA readers only.

Reader A is designated out and Reader B is designated in.

Inputs

The FORTESSA Controller has four input terminal blocks for external devices:

a door sensor input (DR),

a Request to Exit input (RQE),

an Intruder input for connecting to an alarm panel and,

a Fire input for connecting to a fire panel.

Resetting to Factory Defaults

The controller can be reset to factory defaults by pressing and holding the reset button

located at the bottom right of the board for 7 seconds.

Supply

The FORTESSA Controllers require a 12V DC PSU (not supplied). The actual

operating range is between 10V DC and 14V DC.

Network

Figure 1 shows both USB and Ethernet connectivity options to the FORTESSA

controller from a host PC. The upper part of Figure 1 shows the 3801 FORTESSA

Controller using the 3803 FORTESSA USB Interface

The lower part of Figure 1 shows connectivity to the 3802 FORTESSA.net Controller

using a LAN or WAN.

Additional 3801 FORTESSA Controllers can be added to the system by linking them

together in a daisy chain using the FORTESSA Network. Doors Express will support a

maximum of 16 controllers per system.

The End of Line Resistor jumper is set to N as default. This should be changed to Y if

the FORTESSA Controller is the first or last controller on the daisy chain network.

Cable

Network

Two core twisted pair cable is to be used to wire the FORTESSA Network (a screened

cable can be used to offer better protection).

If the optional screened cable is used then the incoming and outgoing screen can be

fitted to SCR on the Network terminal block. It is important to remember that the

screen needs to be earthed to ground at one end of the network.

Reader

The FORTESSA Readers are connected to the FORTESSA Controller using a

standard 4 core cable (alarm cable is suitable).

LEDs

Status

The status LED next to the reset button indicates whether the board has power or not.

Reader (A & B)

The readers LEDs indicate whether the reader circuit is in overload (red) or if there is

activity from the reader itself (green).

Network LEDS

The green LED signifies that data has been received by the controller and the red LED

indicates that there is traffic on the FORTESSA Network.

Relay

The green LEDs illuminate when the relays have been activated.

Fire

The red LED is on when there is a short on the Fire circuit and the green LED is on

when it is in a state of alarm.

Intruder

The red LED is on when there is a short on the Intruder circuit and the green LED is on

when it is in a state of alarm.

Notes on the Fire and Intruder Short Circuit Detector LEDs

The controller comes fitted with resistors between the I/P and 0V terminal blocks on

both the Fire and Intruder inputs. To enable the board to detect a short on either circuit

when fitting to a fire or alarm panel the resistor should be moved to the fire or alarm

panel terminal block output.

FORTESSA Reader (Switch Plate Style)

Front View of FORTESSA Reader

Figure 3

Box Contents

1 x FORTESSA Reader

1 x stainless steel facia

1 x UK standard surface mount single gang back box

2 x security screws

1 x driver bit for security screws

Description

The FORTESSA Reader is a passive RFID (Radio Frequency Identification) proximity

reader for use with the FORTESSA system. The FORTESSA Reader is weather

protected to IP66 and suitable for both indoor and outdoor use.

Power

The FORTESSA Reader uses 12V DC and power is taken from the positive and

negative connections of the Reader terminal block on the FORTESSA Controller

board.

Mounting

Figure 4

Connections

The FORTESSA Reader should be connected to the FORTESSA Controller using a

four core cable. The cable run should be no more than 100 metres. Data is

transferred between the FORTESSA Reader and FORTESSA Controller through the

respective X and Y terminal blocks and should be linked X to X and Y to Y.

Inputs

Door Sensor

A door contact sensor can be fitted to DR on the Door terminal block and the negative

terminal should be wired in to the negative connection on the Reader terminal block.

Request to Exit

A normally open connection, or “push to make” connection, Request to Exit button may

also be fitted to the FORTESSA Reader. The positive of the RQE should be wired in to

RQE on the Door terminal block and the negative should be wired in to the negative of

the Reader terminal block. The FORTESSA reader must be fitted to Reader A on the

FORTESSA Controller and the RQE feature enabled in Doors Express for this

configuration to work

Locking Device

A small strike lock can also be fitted to the reader with a rating of no more than 100mA

by wiring in to the positive and negative Lock terminal block on the FORTESSA

Reader.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Sistema de control de otras marcas

Pentair Pool Products

Pentair Pool Products Compool Manual de usuario

ComfortNET

ComfortNET CTK04 Manual de usuario

Fireye

Fireye InSight II 95DSS3 Manual de usuario

CAME

CAME G3000 Manual de usuario

Idemia

Idemia MorphoAccess VP MD Manual de usuario

Axis

Axis P1445-LE-3 Manual de usuario

HEIDENHAIN

HEIDENHAIN TNC 150 B Manual de usuario

CNC-Step

CNC-Step High-Z T-Series Manual de usuario

Doosan

Doosan DVF Series Manual de usuario

Honeywell

Honeywell KAP 140 Manual de usuario

Honeywell

Honeywell vk41 series Manual de usuario

AirBench

AirBench FPW Guía de instalación

Cypress

Cypress HHR-3160 Manual de usuario

CAME

CAME GLT40AOS Manual de usuario

Zonex

Zonex GEN II -VVT Guía del usuario

Altronics

Altronics K 9650 Manual de usuario

micro-trak

micro-trak RoadMaster Manual de usuario

micro-trak

micro-trak Calc-An-Acre II Manual de usuario

fortessa 3800-F Manual de usuario

Manuales populares de Sistema de control de otras marcas