Forney 140 MP Manual de usuario

Assemble top handle and bottom

supports. (Tools needed: screwdriver)

Attach gas bottle and regulator hose

assembly. (Tools needed: adjustable

wrench)

Use Process Selector Knob to select

desired process.

Adjust polarity for the stick electrode.

Disconnect MIG gun as it will be

electrically “hot” while Stick welding.

Adjust amperage.

Adjust hot start if needed.

Attach TIG torch and Foot Pedal if

desired.

Verify proper shielding gas is used

for TIG welding.

Disconnect MIG gun as it will be

electrically “hot” while Stick welding.

Adjust amperage.

* Torch & Foot Pedal sold seperately

WARNING: To prevent serious injury, read manual warnings and instructions before use.

140 MP WELDER QUICK START GUIDE

WARNING: To prevent fire and serious injury: Keep torch and wire clear of grounded objects while welder is plugged in. Be sure to

follow safe welding proceedures and wear proper PPE (clothes, welding helmet, safety glasses, welding gloves, boots, etc.)

STICKMIG TIG

(Most MIG shielding gases

will not work)

(Usually DCEP - Electrode

Positive).

Install wire spool.

Install MIG gun, turn it on, and

squeeze trigger until wire comes out.

Adjust wire feed tension.

Adjust wire feed speed and voltage

per chart on the inside of welder.

Verify drive rolls, liner and tips are

properly sized for desired wire

diameter.

Verify polority is set

correctly for MIG or

Flux-core welding wire.

Adjust

Tension

Knob

STICK WELDING TIPS

TIG WELDING TIPS

• Optimal stickout varies

by electrode type and

diameter but is usually

approximately 1/16”

• Provides higher

amperage at arc start

to prevent electrode

sticking

OPTIMAL STICKOUT HOT START

• Affects penetration and

bead width

• Can also affect spatter,

electode starting and

ability to weld vertical

or overhead

AMPERAGE

• Affects bead width

and height

• Can also affect

penetration

TRAVEL SPEED

1/16”

• Optimal stickout varies

by electrode type and

diameter but is usually

approximately 1/16”

• A scratch or lift Start is

often used to initiate

the arc

•

Try to minimize

electrode and tungsten

contamination

OPTIMAL STICKOUT ARC START

• Affects penetration and

bead width

• Amperage is often

referred to as “heat” in

TIG Welding

AMPERAGE

• Affects bead width and

height

•

Can also affect penetration

TRAVEL SPEED

1/16”

MIG WELDING TIPS

STICK WELDING TIPS

• Stickout

1/2

”

+/-

1/8

”

• Short stickout = more

current and more

penetration

• Affects the arc shape

• Less voltage = tighter

arc and potentially

more spatter

OPTIMAL STICKOUT VOLTAGE

• Higher wire feed speed

equals more amperage

• Can also affect arc

shape and penetration

WIRE FEED SPEED

(WFS)

• Affects bead width

and height

• Can also affect

penetration

TRAVEL SPEED

1/2”

Otros manuales para 140 MP

Otros manuales de Sistema de soldadura de Forney

Forney

Forney Easy Weld 20P Manual de usuario

Forney

Forney Easy Weld 20P Manual de usuario

Forney

Forney 190 Manual de usuario

Forney

Forney 430 Manual de usuario

Forney

Forney 220 AC/DC Manual de usuario

Forney

Forney 325P Manual de usuario

Forney

Forney 410 Manual de usuario

Forney

Forney 250P+ Manual de usuario

Forney

Forney 235 Manual de usuario

Forney

Forney 210 Manual de usuario

Forney

Forney 700P Manual de usuario

Forney

Forney 242 Manual de usuario

Forney

Forney 270 MIG Manual de usuario

Forney

Forney Easy Weld 140FC-i Manual de usuario

Forney

Forney 210 MIG Manual de usuario

Forney

Forney 140 MP Manual de usuario

Forney

Forney EASY WELD 100 ST Manual de usuario

Forney

Forney 298 Manual de usuario

Forney

Forney Easy Weld 261 Manual de usuario

Forney

Forney 180 ST+ Manual de usuario

Forney

Forney MIG 180FI Manual de usuario

Forney

Forney 95FI Manual de usuario

Forney

Forney 270 Manual de usuario

Forney

Forney 220 ST Manual de usuario

Manuales populares de Sistema de soldadura de otras marcas

Berner

Berner PLASMACUT 54 Manual de usuario

Pro Spot

Pro Spot PR-155 Manual de usuario

Thermal Arc

Thermal Arc 400S Manual de usuario

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manual de usuario

GYS

GYS PROTIG 201 AC/DC Manual de usuario

TAFA

TAFA 30*8B35 Manual de usuario

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manual de usuario

ESAB

ESAB Buddy Arc 145 Manual de usuario

CIGWELD

CIGWELD 636804 Guía rápida

Red-D-Arc

Red-D-Arc DC-400 Manual de usuario

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario

Elettro

Elettro HI-MIG 3000 SYNERGIC Manual de usuario

WIA

WIA Weldmatic 270 CP132-2 Manual de usuario

Sonics

Sonics H520T Manual de usuario

Miller

Miller Big Blue 400D Manual de usuario

NewArc

NewArc RT2000 Guía de inicio rápido

Hypertherm

Hypertherm powermax1000 Manual de usuario

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manual de usuario