** WARNING **
•DOES NOT COMPLY WITH UL2034.
•ENSURE YOU ALSO HAVE A UL2034 compliant CO DETECTOR.
•CO IS A TOXIC GAS and CAN KILL YOU.
•DO NOT TAMPER and DO NOT OPEN THE UNIT.
•NOT TO BE USED IN CORROSIVE GAS AREAS.
•DO NOT BLOCK THE GRILLED VENTS / SLOTS.
•THE UNIT CANNOT sustain EXCESSIVE SCHOCK.
•THIS IS NOT A SMOKE OR FIRE DETECTOR.
•DO NOT PAINT ON OR NEAR THE MONITOR
•DO NOT SPRAY AIR REFRESHENER, CLEANING SUPPLIES, OR
INSECT KILLER NEAR THE UNIT.
•UNIT DESIGNED ONLY FOR INDOOR USE,
•DO NOT TEST THE UNIT WITH EXHAUST GAS
•DISPOSE UNIT 5 YEARS after Production Date.
•DEPRESS THE TEST BUTTON WEEKLY
•Take each ALARM seriously!
1. FEATURES
1. Low-level display, display >10ppm.
2. Fast alarming when CO > 25ppm.
3. 5-year sensor life.
4. Low battery warning.
5. Product stable on table, no need to mount.
6. End of life warning.
7. 1-year limited warranty.
2. SPECIFICATIONS
Power Source: 3 x AA 1.5V battery
Sensor Type: Electrochemical, 5 year life
Target Gas: Carbon Monoxide
Alarm activation: 25 ppm
CO Display Range: 0-9ppm …displays “0”
10-999ppm …displays level
Accuracy: +/- 30% of reading
Operation Temp: 40 to 100F
Ambient Humidity: 5% to 90%
Buzzer Level: 85dB @ 1m
Product Weight: 200g
Product Life: 5 years of Label Date
Product Size: 140x66x35mm
3. CARBON MONOXIDE GAS
Carbon monoxide (CO) is a colorless, odorless, and tasteless poison gas
that can be fatal when inhaled. CO inhibits the blood's capacity to carry
oxygen. Inside your home, appliances used for heating and cooking are the
most likely sources of CO. CO can be produced when burning any fossil
fuel: gasoline, propane, natural gas, oil and wood. CO can be produced by
any fuel-burning appliance that is malfunctioning, improperly installed, or
not ventilated correctly. Possible CO sources include furnaces, gas
ranges/stoves, gas clothes dryers, water heaters, portable fuel burning
space heaters, fireplaces, wood-burning stoves and swimming pool
heaters. Blocked chimneys or flues, back drafting and changes in air
pressure, corroded or disconnected vent pipes, or a loose or cracked
furnace exchanger can also release CO into your home or space. Vehicles
and other combustion engines running in an attached garage or using a
charcoal/ gas grill or hibachi in an enclosed area are sources of CO.
4. SYMPTOMS OF CO POISONING
Initial carbon monoxide poisoning symptoms include dizziness, severe
headaches, nausea, vomiting and disorientation. Everyone is susceptible
but experts agree that unborn babies, pregnant women, senior citizens
and people with heart or respiratory problems are especially vulnerable. If
symptoms of carbon monoxide poisoning are experienced seek medical
attention immediately. CO poisoning can be determined by a
carboxyhemoglobin blood test. The following symptoms are related to
CARBON MONOXIDE POISONING and should be discussed with ALL
members of the household:
•Mild Exposure: Slight headache, nausea, vomiting, fatigue (often
described as “Flu-like” symptoms).
•Medium Exposure: Severe throbbing headache, drowsiness,
confusion, fast heart rate.
•Extreme Exposure: Unconsciousness, convulsions, cardio
respiratory failure and death.
The levels of exposure relate to healthy adults. Levels differ for those at
higher risk. Exposure to high levels of carbon monoxide can be fatal or
cause permanent damage and disabilities. Many cases of reported carbon
monoxide poisoning indicate that while victims are aware they are not
feeling well, they become so disoriented they are unable to save
themselves by either exiting the building/home, or calling for assistance.
Also, young children and household pets may
be the most sensitive. Familiarization with the effects of each level is
important. Please be attentive and it is your responsibility.
5. RECOMMENDED LOCATIONS
CO alarms should be mounted in or near bedrooms and living areas. It is
recommended that you install the CO alarm (at minimum) on each level of
your home. When choosing your installation locations, make sure you can
hear the alarm from all sleeping areas. If you install only one CO alarm in
your home, install it near bedrooms, not in the basement or furnace room.
When wall mounting, keep it out of the reach of children, pets or
accidental bumps. Under no circumstances should children be allowed to
handle the CO alarm. Placing the alarm at eye level is recommended as
it allows for optimum daily monitoring of the digital display.
6. LOCATIONS TO AVOID
•Do not install in areas where the temperature is colder than 40°F
(4.4°C) or hotter than 100°F (37.8°C) such as crawl spaces, attics,
porches and garages.
•Do not install within 5 ft. of heating or cooking appliances.
•Do not install near vents, flues, chimneys or any forced/unforced air
ventilation openings.
•Do not install near ceiling fans, doors, windows or areas directly
exposed to the weather so external air, water or rain reaches the
alarm.
•Do not install in dead air spaces, such as peaks of vaulted ceilings or
gabled roofs, where CO may not reach the sensor in time to provide
early warning.
•Do not install on a switched or dimmer-controlled outlet.
•Do not install this unit near deep-cell large batteries. Large batteries
have gas emissions that can cause the alarm to perform at less than
optimum performance.
•Do not obstruct the vents located on the alarm. Do not place the alarm
where drapes, furniture or other objects block the flow of air to the
vents.
7. INSTALLATION
The detector comes with batteries included in the battery
compartment. Open the compartment by sliding the battery cover.
Remove the plastic covering the batteries. The Detector then turns
ON. Establish a mount location considering the prior locations to
avoid.
Having established the mounting location, ensure that there is no
electrical wiring or pipe work in the area adjacent to the mounting
surface. The detector comes with (a) mount plate (b) 2 x screw and
(c) 2 x plastic drywall expansion anchors.
•Remove the mount plate from the detector by sliding it off.
Mark the two mount hole locations on a wall using the
backplate holes as a guide.
•Drill holes in the positions marked using a 5mm drill bit.
•Insert the plastic drywall expansion anchors.
•Install the mount plate, align the holes and screw the screws into
the anchors.
•Slide the detector onto the mount plate.
•The detector is ready for continuous operation.
For tabletop placement, simply place the CO alarm on the table, so
that the users can see the alarm clearly.
