Forcepoint 120 Series Instrucciones de instalación
Next Generation
Firewall
120 Series
Model 120W (APP-120C1)
Internet Security Device
Hardware Guide
Revision A
Next Generation Firewall Hardware Guide | Model 120W
Contents
■Introduction on page 2
■Find product documentation on page 2
■Model 120W features on page 3
■Indicator lights on page 5
■Ethernet port indicators on page 6
■Precautions on page 6
■Install the appliance on page 8
■Turn off the appliance on page 12
■Compliance information on page 12
Introduction
Thank you for choosing a Forcepoint appliance.
Familiarize yourself with the appliance ports and indicators and learn how to install the appliance safely.
Find product documentation
On the Forcepoint support website, you can find information about a released product, including product
documentation, technical articles, and more.
You can get additional information and support for your product on the Forcepoint support website at
https://support.forcepoint.com. There, you can access product documentation, release notes, Knowledge Base
articles, downloads, cases, and contact information.
You might need to log on to access the Forcepoint support website. If you do not yet have credentials, create a
customer account. See https://support.forcepoint.com/CreateAccount.
2
Next Generation Firewall Hardware Guide | Model 120W
Model 120W features
The figures and tables show the components and features of the 120W (APP-120C1) appliance.
Front panel
This panel has the following parts.
1 2 3 4
1USB port
2Indicators for Ethernet interface port activity and link status
3Indicators for status, management (MGMT), high availability (HA), and power over Ethernet (PoE)
4Indicators for wireless LAN (WLAN) connectivity, power (PWR), and disk activity (SSD)
3
Next Generation Firewall Hardware Guide | Model 120W
Back panel
This panel has the following parts.
1
82 3 4 9 105 6 7
1Antenna connectors
2Grounding point
3Power connector DC IN 1 — Provides 12V DC power for the appliance.
4Power connector DC IN 2 — Optionally provides 54V DC power for the power over Ethernet (PoE) ports.
Note
PoE is an optional feature. A power adapter and power cable for PoE are not included with
the delivery. To use PoE, you must purchase them separately.
5Fixed Ethernet ports 6 and 7 from top to bottom.
When a power adapter is connected to power connector DC IN 2, fixed Ethernet ports 6 and 7 provide
power over the Ethernet cable for other devices that are compatible with the 802.3at standard.
PoE on these ports is active and uses LLDP for power negotiation.
6Fixed Ethernet ports 4 and 5 from top to bottom.
7Fixed Ethernet ports 2 and 3 from top to bottom.
If you use the appliance in an NGFW Engine cluster, use fixed Ethernet port 2 for the heartbeat
connection between the nodes.
8Fixed Ethernet ports 1 and 0 from left to right.
Ethernet ports 1 and 0 are intended for the WAN connection.
9Console port (speed 115,200 bps) and USB port
10 Power button.
4
Next Generation Firewall Hardware Guide | Model 120W
Indicator lights
Indicator lights show the status of the appliance and any fixed Ethernet ports.
1
2
1Ethernet port indicators
2Status indicators
Indicator Color Description
Unlit No link.Activity/
link status
light for
each
Ethernet
port
(Activity)
Green Link OK. Flashes on activity.
Unlit 10 Mbps link.
Amber 100 Mbps link.
Link
speed
light for
each
Ethernet
port (Link)
Green 1 Gbps link.
Unlit The initial configuration has not yet been generated.
Amber Flashes while initial contact is being established. Steady amber when initial contact
has been established, but the NGFW Engine is offline.
Alternates with green when the NGFW Engine is in the standby state.
Status
Green Flashes when initial contact is established, but a policy has not been installed. Steady
green when the NGFW Engine is online.
Unlit The NGFW Engine has made initial contact but no policy is yet installed.
MGMT
Green Flashes when the NGFW Engine tries to make initial contact or when the NGFW
Engine is reconnecting to the Log Server. Steady green when initial contact with
the Management Server has been made, the management connection has been
established, and a policy has been installed.
Unlit The NGFW Engine does not have a clustering configuration.
HA
Green The NGFW Engine has a clustering configuration.
PoE Unlit There is no power feed to any of the Ethernet ports that support power over Ethernet
(PoE).
5
Next Generation Firewall Hardware Guide | Model 120W
Indicator Color Description
Green Power feed is active on at least one of the Ethernet ports that support PoE.
Unlit No WLAN access point is available for clients to connect to.
WLAN
Green A WLAN access point is available for clients to connect to.
Unlit No power source is connected to the appliance.
Green Power is supplied to the appliance.
PWR
Red The appliance is in a standby state.
SSD Green Flashes on disk activity.
Ethernet port indicators
Ethernet port indicators show the status and speed of the network ports.
1 2
1 2
1Activity/link indicator
2Link speed indicator
Indicator Color Description
Activity/link indicator Green Steady when link is present. Flashes on activity.
Unlit No link.
Unlit 10 Mbps link.
Amber 100 Mbps link.
Link speed indicator
Green 1 Gbps link.
Precautions
The precautions provide safety guidance when working with Forcepoint appliances and electrical equipment.
CAUTION
Forcepoint appliances cannot be serviced by end users. Never open the appliance covers for any
reason. Doing so can lead to serious injury and void the hardware warranty.
6
Next Generation Firewall Hardware Guide | Model 120W
For additional safety information, see the Forcepoint Product Safety and Regulatory Compliance Guide.
General safety precautions
Read the safety information and follow these rules to ensure general safety whenever you are working with
electronic equipment.
■Keep the area around the appliance clean and free of clutter.
■Use a regulating uninterruptible power supply (UPS) to keep your system operating during power failures and
to protect the appliance from power surges and voltage spikes.
■If you need to turn off or unplug the appliance, always wait at least five seconds before turning on or plugging
in the appliance again.
Operating precautions
Follow these precautions when operating the appliance.
■Do not open the power adapter casing. Only the manufacturer's qualified technician can access and service
power adapters.
WLAN precautions
Data traffic by a wireless connection might allow unauthorized third parties to receive data. Take the necessary
steps to secure your radio network.
See http://www.wi-fi.org for information about securing your WLAN.
Restrictions and requirements might apply for authorizing wireless devices. Check with your local authorities for
additional information.
Electrical safety precautions
Follow basic electrical safety precautions to protect yourself from harm and the appliance from damage.
■Know the locations of the power on/off button and the emergency turn-off switch, disconnection switch, or
electrical outlet for the room. If an electrical accident occurs, you can quickly turn off power to the system.
■When working with high-voltage components, do not work alone.
■When working with electrical equipment that is turned on, use only one hand. This is to avoid making a
complete circuit, which causes an electric shock. Use extreme caution when using metal tools, which can
easily damage any electrical components or circuit boards the tools come into contact with.
■Do not use mats designed to decrease electrostatic discharge as protection from electric shock. Instead, use
rubber mats that have been designed as electrical insulators.
■If the power supply cable includes a grounding plug, the plug must be plugged into a grounded electrical
outlet.
■Use only the power cable or cables supplied with the appliance.
■Outdoor devices connected to the appliance must be placed on the same building as where the appliance is
located. The devices must also be installed so they are protected from lightning strikes, for example under a
roof.
7
Next Generation Firewall Hardware Guide | Model 120W
Note
Standby power is supplied to the appliance even when the appliance is turned off.
AC power supply safety precautions
The appliance power inlet is the disconnect device on the appliance.
Install the appliance
There are several tasks that must be completed before the appliance is installed.
These tasks and the installation of the appliance might be done by the same person or by different persons:
■The Security Management Center (SMC) administrator is responsible for the tasks that are needed before the
appliance is installed.
■The on-site installer is responsible for installing the appliance.
For more information, see the Forcepoint Next Generation Firewall Installation Guide.
To prepare for the appliance installation, the SMC administrator must do the following:
1) If the SMC has not yet been installed, install the SMC.
Important
Do not install the SMC on the NGFW appliance.
The SMC can manage many NGFW appliances.
2) In the Management Client component of the SMC, create and configure the NGFW Engine element that
represents the appliance.
3) In the Management Client component of the SMC, save the initial configuration.
The SMC administrator must either:
■Upload the initial configuration to the Installation Server for plug-and-play configuration of the appliance.
Note
There are additional requirements for plug-and play configuration. See Knowledge Base
article 9662.
■Give the on-site installer a USB drive that contains an initial configuration file for each appliance.
The on-site installer must do the following:
1) Inspect the appliance, delivery box, and all components included in the shipment.
Important
Do not use damaged appliances or components.
2) Connect all necessary power and network cables and other components, then turn on the appliance.
8
Next Generation Firewall Hardware Guide | Model 120W
If the plug-and-play configuration method is not used, the on-site installer must use the USB drive that
contains the initial configuration files to configure the NGFW Engine software.
3) When you have finished installing the appliance, inform the SMC administrator so that the administrator can
check the status of the appliance in the Management Client.
Attach the antennas
Attach the three antennas included in the delivery to the appliance.
Before you begin
Before you attach or replace the antennas, you must turn off the appliance.
Steps
1) Locate the antennas included in the appliance delivery.
2) Attach the antennas to the connectors on the back panel of the appliance.
3) Tighten the knurled nuts at the base of the antennas to secure them firmly to the appliance.
4) While holding the base of the antennas, position the antennas.
Mount the 120W appliance on a wall
You can optionally mount the 120W appliance on a wall.
Important
There are vents on the sides of the appliance. Keep other objects at least 100mm (4 inches) away
from the appliance to ensure good air flow. Do not stack appliances.
Mounting the appliance on a wall has the following requirements:
■You can mount the appliance in a horizontal orientation only with the connectors for the cables facing down.
■The distance between the holes that you drill for the appliance in the wall must be 120mm (4.7 inches).
■Depending on the wall material, you might need to insert nylon plugs into the mounting holes that you drill for
the appliance. No nylon plugs are supplied with the appliance.
■Two flat undercut screws are required. No screws are supplied with the appliance.
The diameter of the screw heads must be 5.5mm (7/32 inch) and the thickness of the screw heads must be
2mm (5/64 inch).
Select screws that are suitable for the wall material and long enough to provide a firm mounting point for the
appliance. If you have attached the four provided rubber feet to the bottom of the appliance, make sure that
the screws are long enough to provide a firm mounting point for the appliance with the feet attached.
9
Next Generation Firewall Hardware Guide | Model 120W
Make sure that the heads of the screws fit into the mounting holes on the bottom of the appliance before you
drill the mounting holes in the wall.
Steps
1) Drill two holes 120mm (4.7 inches) apart in the wall in a horizontal orientation.
Make sure that you leave enough clearance around the appliance.
2) If required, insert nylon plugs into the holes.
3) Insert the two screws into the holes and tighten the screws.
Make sure that the screws are protruding from the wall to provide a firm mounting point for the appliance.
4) Align the mounting holes on the appliance with the screws, then place the appliance on the screws so that
the cables are below the appliance.
After the appliance is mounted on the wall and you have connected the cables, do not pull on the cables.
CAUTION
If you need to disconnect any cables after the appliance is mounted on the wall, hold the
appliance in place while you disconnect the cables.
Connect the cables
Connect the network and power cables.
Use at least CAT5e-rated cables for gigabit networks.
Network interfaces at both ends of each cable must have identical speed and duplex settings. These settings
include the automatic negotiation setting. If one end of the cable uses autonegotiation, the other end must also
use autonegotiation. Gigabit standards require interfaces to use autonegotiation. Fixed settings are not allowed at
gigabit speeds.
Connect network cables
Ethernet ports are mapped to interface IDs during the initial configuration. Determine which Ethernet ports to use
for connecting to your networks.
Steps
1) Connect network cables to the Ethernet ports.
If you use the plug-and-play configuration method, the appliance uses Ethernet port 0 to contact the
Installation Server.
If the appliance is a node in an NGFW Engine cluster, connect the cable for the heartbeat connection
between the nodes to Ethernet port 2.
10
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Cortafuegos de Forcepoint
Forcepoint
Forcepoint V10000 Manual de instalación y operación
Forcepoint
Forcepoint NGFW Manual de usuario
Forcepoint
Forcepoint S4016 Instrucciones de instalación
Forcepoint
Forcepoint V5000 Manual de usuario
Forcepoint
Forcepoint 3201 Instrucciones de instalación
Forcepoint
Forcepoint 110 Instrucciones de instalación
Forcepoint
Forcepoint 2200 Series Instrucciones de instalación
Forcepoint
Forcepoint V5000 G4R2 Manual de usuario
Forcepoint
Forcepoint Stonesoft 320X Instrucciones de instalación
Forcepoint
Forcepoint 330 Series Instrucciones de instalación
Forcepoint
Forcepoint V5000 G2 Manual de usuario
Forcepoint
Forcepoint N120 Instrucciones de instalación
Forcepoint
Forcepoint NGFW 51 Manual de usuario
Forcepoint
Forcepoint V5000 G4 Manual de usuario
Forcepoint
Forcepoint 110 Instrucciones de instalación
Forcepoint
Forcepoint V10000 G3 Manual de usuario
Forcepoint
Forcepoint 3201 Instrucciones de instalación
Forcepoint
Forcepoint 6205 Instrucciones de instalación
Forcepoint
Forcepoint V5000 G4 Manual de usuario
Forcepoint
Forcepoint 350 Series Instrucciones de instalación
