Force America SSC6100 CAN ULTRA Manual de usuario
SSC6100 CAN ULTRA
Spreader Control
Operation Manual
Firmware Version
1.11.1035
SSC6100 Operation Manual
Welcome and Table of Contents
i
Welcome
Congratulations on your purchase of a FORCE America®, Inc. SSC6100 Spreader Control. This
manual will guide you through the process of using your new spreader control.
Table of Contents
Welcome ...........................................................................................................i
Table of Contents.............................................................................................i
Hardware..........................................................................................................1
Core Module (PN: 1104694).................................................................................................. 4
Operator Interface (PN: 1104696)........................................................................................ 6
20 Port Valve Module (PN: 1018887)................................................................................... 7
10 Port Valve Module (PN: 1101182)................................................................................... 9
7-Inch LCD Display (PN: 1104695) .................................................................................... 11
6100 Event Logging Authentication Module (PN: 1016063) ........................................... 12
Direct Liquid Application Module (PN: 1018830)............................................................. 13
Powering up the SSC6100............................................................................15
System Operation..........................................................................................18
The Spreader Power Off Screen........................................................................................ 18
The Operation Screen......................................................................................................... 19
Monitoring System Status.................................................................................................. 74
Entering Menus................................................................................................................... 75
Implements Menu..........................................................................................76
Material Selection Menu ...............................................................................78
Data Menu......................................................................................................81
Viewing a Report................................................................................................................. 85
Summary Report................................................................................................................. 86
Detailed Report ................................................................................................................... 87
Error Log.............................................................................................................................. 88
Unload Menu..................................................................................................89
Granular Unload.................................................................................................................. 90
Tow Granular Unload.......................................................................................................... 93
Prewet Unload..................................................................................................................... 96
Tow Prewet Unload............................................................................................................. 99
Direct Unload..................................................................................................................... 102
Setting Sim Speed.......................................................................................108
Distance Measure........................................................................................109
Joysticks......................................................................................................111
Switches.......................................................................................................113
SSC6100 Operation Manual
Welcome and Table of Contents
ii
Automatic Recall of Joystick Functions......................................................................... 113
Enable or Disable a Joystick ........................................................................................... 113
Change a Joystick to an Alternate Function.................................................................. 114
Run a Low Current Function ........................................................................................... 114
Powering Down the SSC6100.....................................................................115
Troubleshooting and Error Conditions .....................................................116
Header Bar Warnings ....................................................................................................... 116
Error Windows .................................................................................................................. 120
In-Line Errors .................................................................................................................... 127
The Emergency Stop Warning Screen............................................................................ 133
Joystick Error Codes........................................................................................................ 134
Licensing and Source Code Availability ...................................................135
FORCE America Contact Information........................................................135
Appendix A –GNU General Public License, Version 2............................136
SSC6100 Operation Manual
Hardware
1
Hardware
Every SSC6100 comes with at least 4 components:
Core Module
(PN: 1104694)
Operator Interface
(PN: 1104696)
7-Inch LCD Display
(PN: 1104695)
SSC6100 Operation Manual
Hardware
2
20 Port Valve Module
(PN: 1018887)
or
10 Port Valve Module
(PN: 1101182)
SSC6100 Operation Manual
Hardware
3
In addition, your spreader control may ship with one or more of the following optional
components:
6100 Event Logging Authentication
Module, 6100-ELA-Module
(PN: 1016063)
Direct Liquid Application Module
(PN: 1018830)
For more information on hardware pinouts and
connections, refer to Schematic 3388, included
in the SSC6100 Binder.
SSC6100 Operation Manual
Hardware
4
Core Module (PN: 1104694)
The Core Module is the heart of the SSC6100 system. It acts as the central point of
communication for all CAN devices, processing all the inputs and redirecting them to the
appropriate outputs.
The Core Module is mounted vertically on the floor of the vehicle. Its LEDs face up towards the
driver to present status information.
The top of the Core Module has 6 status LEDs, as shown in Figure 1:
Figure 1: Top of the Core Module
Label
LED
Function
Power
On
This LED displays the presence of the vehicle’s ignition switch. This LED
is lit when the vehicle’s ignition switch is in the powered position and is
unlit when it is off.
Status
This LED confirms the operating status of the SSC6100 hardware. This
light should blink if the SSC6100 hardware initialized successfully.
FCAN
XMT
This LED blinks when the Core Module transmits data on the CAN bus.
RECV
This LED blinks when the Core Module receives data from the CAN bus.
VCAN
XMT
This LED blinks when the Core Module transmits data on the CAN bus.
SSC6100 Operation Manual
Hardware
5
Label
LED
Function
RECV
This LED blinks when the Core Module receives data from the CAN bus.
The front of the Core Module has a single USB port, which can be used to import and export
calibration files or material usage reports. The ports on the back of the core module are used as
connectors to the Operator Interface, 20 Port Valve Module, 10 Port Valve Module, LCD Display,
and temperature sensor.
Do not attempt to connect the DVI connector
on the Core Module to any other device
besides a Force America 7 Inch LCD Display.
You may damage your equipment.
For more information on the ports on the back
of the Core Module, refer to the installation
drawing included in the SSC6100 Binder.
SSC6100 Operation Manual
Hardware
6
Operator Interface (PN: 1104696)
The Operator Interface lets you control all the aspects of the SSC6100.
Figure 2: Operator Interface
The Operator Interface has two single-axis encoders, one triple-axis encoder, and eight “soft
switches” that act as pushbuttons for SSC6100 functions. The functions that they control change
depending on what portion of the SSC6100 system is active. See System Operation on page 18.
Otros manuales para SSC6100 CAN ULTRA
4
Tabla de contenidos
Otros manuales de Sistema de control de Force America
