Focusrite ITrack Solo Manual de usuario

User Guide

www.focusrite.com

FA0687-03

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus with water.

6. Clean only with dry cloth.

7. Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including ampliﬁers) that produce heat.

8. Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

9. Only use attachments/accessories speciﬁed by the manufacturer.

10. Use only with the cart, stand, tripod, bracket, or table speciﬁed by the manufacturer, or

sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

11. Unplug this apparatus during lightning storms or when unused for long periods of time.

12. Refer all servicing to qualiﬁed service personnel. Servicing is required when the apparatus

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has

been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain

or moisture, does not operate normally, or has been dropped.

13. No naked ﬂames, such as lighted candles, should be placed on the apparatus.

WARNING: Excessive sound pressure levels from earphones and headphones can cause hearing

loss.

WARNING: This equipment must only be connected to USB 2.0 type ports.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning ﬂash with arrowhead symbol, within equilateral triangle,

is intended to alert the user to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may be of sufﬁcient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to

alert the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the appliance.

ENVIRONMENTAL DECLARATION

For USA

To the User:

1. Do not modify this unit! This product, when installed as indicated in the instructions contained in this

manual, meets FCC requirements. Modiﬁcations not expressly approved by Novation may void your authority,

granted by the FCC, to use this product.

2. Important: This product satisﬁes FCC regulations when high quality shielded cables are used to connect

with other equipment. Failure to use high quality shielded cables or to follow the installation instructions

within this manual may cause magnetic interference with appliances such as radios and televisions and

void your FCC authorization to use this product in the USA.

3. Note: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Compliance Information Statement: Declaration of Compliance procedure

Product Identiﬁcation: Focusrite iTrack Solo

Responsible party: American Music and Sound

Address: 5304 Derry Avenue #C

Agoura Hills,

CA 91301

Telephone: 800-994-4984

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired

operation.

For Canada

To the User:

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

RoHS Notice

Focusrite Audio Engineering Limited has conformed and [its/this] product[s] conform[s], where applicable, to the European Union’s

Directive 2002/95/EC on Restrictions of Hazardous Substances (RoHS) as well as the following sections of California law which refer to

RoHS, namely sections 25214.10, 25214.10.2, and 58012, Health and Safety Code; Section 42475.2, Public Resources Code.

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS .............................................. 2

TABLE OF CONTENTS ........................................................... 4

OVERVIEW..................................................................... 5

Introduction .................................................................5

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Box Contents ................................................................5

System Requirements.........................................................6

Compatible iOS devices ..........................................................6

Mac OS .......................................................................6

Windows ......................................................................6

GETTING STARTED ............................................................. 7

Using the iTrack Solo with an iOS device..........................................7

Powering the iTrack Solo.........................................................7

Connections to your iOS device....................................................7

Using the iTrack Solo with GarageBand.............................................8

Using the iTrack Solo with a Mac or PC...........................................9

Software Installation ............................................................9

Mac OS .......................................................................9

Windows .....................................................................10

Connecting your iTrack Solo ...................................................10

Audio setup in your DAW ........................................................10

Example of use .............................................................12

Connecting a microphone / instrument ............................................12

Using Direct Monitoring.........................................................13

Headphone monitoring .........................................................13

Connecting iTrack Solo to loudspeakers ...........................................13

HARDWARE FEATURES.........................................................14

Front Panel.................................................................14

Back Panel .................................................................15

PERFORMANCE SPECIFICATIONS ................................................16

Physical and Electrical Characteristics..........................................17

TROUBLESHOOTING ...........................................................17

OVERVIEW

Introduction

Thank you for purchasing this iTrack Solo, one of the family of Focusrite professional computer audio

interfaces incorporating high quality Focusrite analogue pre-ampliﬁers. You now have a simple and

compact solution for routing high quality audio to and from your iPad, iPad 2, iPad (3rd Generation)

or computer.

This User Guide provides a detailed explanation of the hardware to help you achieve a thorough

understanding of the product’s operational features. We recommend that both users who are new

to computer-based recording, as well as more experienced users, take the time to read through

the user guide so that you are fully aware of all the possibilities that the iTrack Solo has to offer.

If the main User Guide sections do not provide the information you need, be sure to consult

http://www.focusrite.com/answerbase, which contains a comprehensive collection of common

technical support queries.

Features

The iTrack Solo audio interface allows you to connect a microphone and/or guitar to an iPad, iPad 2

or iPad (3rd Generation). The signals connected to the physical inputs of the iTrack Solo can then be

routed to your audio recording app - for example, GarageBand. It can also be used to route audio to a

digital audio workstation (referred to throughout this user guide as a “DAW”) running on a laptop (or

desktop) using either Mac OS or Windows. In either case, the monitoring output from the recording

app or DAW will appear at the iTrack Solo’s physical outputs.

This lets you record “real-world” instruments into GarageBand (or whichever recording app or DAW

you use) along with - or instead of - any “native” sounds already available within your iOS device

or computer. The instruments may be “electric”, i.e., a guitar, or acoustic - anything you can put

a microphone in front of. The iTrack Solo also lets you route the tracks of your DAW to its physical

outputs, which can be connected to an ampliﬁer and speakers, powered monitors, headphones,

or any other audio equipment with analogue inputs that you wish to use. Although all inputs and

outputs on the iTrack Solo are routed directly to and from your DAW for recording and playback, you

can conﬁgure the routing within your DAW in order to meet your needs.

Box Contents

Along with your iTrack Solo you should have:

• Software activation card providing activation codes for:

- Focusrite Scarlett Plug-in Suite

- Ableton Live Lite

• Device Link cable (iTrack Solo to iPad)

• USB cable (Type ‘A’ to Type ‘B’)

• Getting Started Guide

System Requirements

Compatible iOS devices:

iPad, iPad 2, iPad (3rd generation)

Mac OS

Apple Macintosh with a high-speed USB 2.0-compliant USB port

OS: Mac OS X 10.7 or later (Lion or Mountain Lion)

Windows

Windows compatible computer with a USB 2.0-compliant USB port

OS: Windows 7

GETTING STARTED

Using the iTrack Solo with an iOS device

Powering the iTrack Solo

The iTrack Solo is an active device, and needs a DC power source to operate. It is important to

remember that when you use the iTrack Solo with an iPad, it will not be powered from the iOS device

via the interface cable.

Use the supplied USB cable to connect the iTrack Solo to a standard Apple USB Power Supply

(or other standard USB power supply). One of these is supplied with every iOS device, or can be

obtained separately. The front panel USB LED (7) will illuminate when the iTrack Solo is powered

and connected.

It is also important to note that when connected in this way, the iTrack Solo will not charge the iOS

device’s internal battery.

Connections to your iOS device

The supplied iOS interface cable should be connected between the DEVICE LINK port on the rear of

the iTrack Solo and your iPad. This cable will carry the audio between the recording app on your iOS

device and the iTrack Solo in both directions, but does not carry DC power in either direction (see

above).

See “Example of use” on page 12 for details of how to connect audio sources and monitoring

systems to the iTrack Solo.

NOTE: When using the iTrack Solo with an iPad, please enable “Airplane Mode” in the settings menu

to avoid experiencing any interference during recording and playback.

Using the iTrack Solo with GarageBand

GarageBand is one of the most popular recording apps for iOS devices. It is a useful compositional

tool and used on its own, allows you to create music from the range of virtual instruments it provides.

With iTrack Solo, you can add vocals and real-world instruments as well.

To route the iTrack Solo mic input into GarageBand follow the procedure below (operating instructions

for GarageBand are beyond the scope of this User Guide, but the application includes a full set of

Help ﬁles):

1. Open the GarageBand song you are working on.

2. Create a vocal track by tapping the ‘+’ button on the bottom left-hand corner of the screen

and select Audio Recorder.

3. Tap the jack plug icon to open the Input Settings controls.

4. Select Left Channel to route the mic input to the vocal track.

5. Switch Monitor OFF and enable Direct Monitor (8) on the iTrack Solo. See “Using Direct

Monitoring” on page 13 for further details on the beneﬁts of using iTrack’s Direct Monitor

feature.

To record a guitar, follow the procedure below:

1. Open the GarageBand song you are working on.

2. Create a guitar track by tapping the ‘+’ button on the bottom left-hand corner of the screen,

select Guitar Amp Track and scroll to select the desired Amp model to be used.

3. Tap the jack plug icon to open the Input Settings controls.

4. Select Right Channel to route the instrument input to the guitar track.

5. You can use either the internal monitor within GarageBand or the Direct Monitor feature on

the iTrack Solo.

If you are using a different recording app, a similar procedure will be necessary; check the App’s

Help ﬁles for information.

Using the iTrack Solo with a Mac or PC

You can also use your iTrack Solo as an analogue audio I/O (Input-Output) interface to a laptop (or

other computer). This will let you record tracks on your DAW from a microphone, guitar, etc., and

also let you connect loudspeaker or headphone monitoring, so you can hear your work in progress

through an external audio system.

Software Installation

You will need to install the appropriate drivers onto your laptop/computer before you can you use the

iTrack Solo with it. (Drivers are small software applications which ensure that your laptop/computer

communicates correctly and efﬁciently with the iTrack Solo).

The drivers can be downloaded from www.focusrite.com/downloads. Navigate to the iTrack Solo

download area.

Mac OS

Select the Mac disk image (*.dmg) version of the driver to start the download. Double-click the ﬁle

from the Downloads folder and then run the installation package (*.pkg). Follow all on-screen

instructions; a conﬁrmation will be given when the driver has been installed successfully.

Your OS should automatically switch the computer’s default audio outputs to be the USB port to which

the iTrack Solo is connected. To verify this, go to System Preferences > Sound, and set the

input and output to iTrack Solo. For more detailed setup options on a Mac, open Applications

> Utilities > Audio MIDI Setup.

Windows

Double-click the Windows (*.exe) version to start the download. Save the ﬁle to a convenient

location, and when the download has completed, double-click it. Follow all on-screen instructions; a

conﬁrmation will be given when the driver has been installed successfully.

Restart your laptop/computer, and then connect the iTrack Solo to a USB port using the supplied

cable.

Your OS should automatically switch the computer’s default audio outputs to be the USB port to

which the iTrack Solo is connected. To verify this:

on Windows 7 - go to Start > Control Panel > Hardware and Sound > Sound > Manage

Audio Devices and set ‘Default Playback’ and ‘Recording’ to ‘iTrack Solo’.

Connecting your iTrack Solo

IMPORTANT: Before you connect the iTrack Solo to your computer,

please complete the software installation according to the instructions

above. This will ensure that the hardware uses the correct drivers, and

will prevent unexpected behaviour.

The iTrack Solo has a single USB 2.0 port (on the rear panel). Once the software installation is

complete, simply connect the iTrack Solo to your computer using the USB cable provided. (Note that

iTrack Solo is a USB 2.0 device, and thus the USB connection requires a USB 2.0+ compliant port on

your computer. It will not operate correctly with USB 1.0/1.1 ports.) The iTrack Solo will be powered

from the computer via the USB connection.

The iTrack Solo cannot be used with an iOS device and a computer at the same time. If this is

attempted, the iOS device will assume priority, and the iTrack Solo will no longer be available as the

I/O device for the computer DAW application.

Audio setup in your DAW

The iTrack Solo is compatible with any Windows-based DAW that supports ASIO or WDM and any

Mac-based DAW that uses Core Audio. After installing the driver and connecting the hardware,

you can start using the iTrack Solo with the DAW of your choice. Ableton Live Lite may easily be

downloaded from www.ableton.com/live-lite if you do not already have a DAW application installed

on your computer. A card with an activation code is included in the box.

Operating instructions for Ableton Live Lite are beyond the scope of this User Guide, but the

application includes a full set of Help ﬁles.

Please note - your DAW may not automatically select the iTrack Solo as its default I/O device. In this

case, you must manually select ‘iTrack Solo’ (or ‘Focusrite USB 2.0 driver’) as the driver

on your DAW’s Audio Setup* page. Please refer to your DAW’s documentation (or Help ﬁles) if you

are unsure where to select the ASIO/ Core Audio driver. The following example shows the correct

conﬁguration in the Ableton Live Lite Preferences panel (Mac version shown).

Otros manuales para iTrack Solo

Tabla de contenidos

Otros manuales de Equipo de grabación de Focusrite

Focusrite

Focusrite Clarett 8 Pre Manual de usuario

Focusrite

Focusrite Scarlett 18i20 Manual de usuario

Focusrite

Focusrite Saffire Manual de usuario

Focusrite

Focusrite vocaster two Manual de usuario

Focusrite

Focusrite Clarett 8Pre USB Manual de usuario

Focusrite

Focusrite Clarett 4 Pre USB Manual de usuario

Focusrite

Focusrite clarett octopre Manual de usuario

Focusrite

Focusrite Forte Manual de usuario

Focusrite

Focusrite iTrack Dock Studio Pack Manual de usuario

Focusrite

Focusrite Liquid Saffire 56 Manual de usuario

Focusrite

Focusrite Scarlett Third Generation Series Manual de usuario

Focusrite

Focusrite Saffire PRO 40 Manual de usuario

Focusrite

Focusrite OctoPre Digital Option Manual de usuario

Focusrite

Focusrite Cubase 5 Manual de usuario

Focusrite

Focusrite Scarlett 18i20 Manual de usuario

Focusrite

Focusrite iTrack Solo Manual de usuario

Focusrite

Focusrite Blue Range Modules Manual de usuario

Focusrite

Focusrite Saffire Pro 24 DSP Manual de usuario

Focusrite

Focusrite Saffire PRO 14 Manual de usuario

Focusrite

Focusrite Red 8Line Manual de usuario

Focusrite

Focusrite Rednet A16R Manual de usuario

Focusrite

Focusrite Clarett 8 Pre Manual de usuario

Focusrite

Focusrite Clarett 4 Pre USB Manual de usuario

Focusrite

Focusrite Saffire Pro 10 I/O Guide Manual de usuario

Manuales populares de Equipo de grabación de otras marcas

KV2 Audio

KV2 Audio 500 Series Manual de usuario

Robotics Technologies

Robotics Technologies microBus-Cam II Manual de usuario

Seca

Seca 460 Manual de usuario

Cognex

Cognex MVS-8000 Series Manual de usuario

Mect

Mect MPNC006 Series Manual de usuario

Bad Caf

Bad Caf THE LEASH Manual de usuario

Strymon

Strymon NIGHTSKY Manual de usuario

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manual de usuario

Tews Technologies

Tews Technologies TPMC465 Manual de usuario

Honeywell

Honeywell Excel 50 Manual de usuario

SeaLevel

SeaLevel COMM+8.LPCI Manual de usuario

Arturia

Arturia AUDIOFUSE STUDIO Manual de usuario

Rukra

Rukra RK-1240 Manual de usuario

Samson

Samson SCOM Manual de usuario

Dynacord

Dynacord DPS260 Manual de usuario

Nice

Nice Core Manual de usuario

Pyle Pro

Pyle Pro PSS8 Manual de usuario

RF-System

RF-System TinyGate Manual de uso y cuidado