Foc.us ERGOFOCUS Manual de usuario

Tested by OMNI-Test Laboratories, Inc. and approved to

ULC-S610-M87 (A1998), UL 737-1996 and ULC S627-00

US EPA exempt

Report Number : 304-F-04-2

This document was packed with the appliance.

KEEP THESE INSTRUCTIONS FOR FUTURE USE

ERGOFOCUS

____

DESIGN INSTALLATION &

OPERATING MANUAL

Introduction

Table

of contents

Please read this entire manual before you install and use

your focus fireplace. Failure to follow instruction may result

in property damage, bodily injury or even death. When this

room heater is not properly installed, a house fire may result.

To reduce the risk of fire, follow the installation instructions.

Contact local building or fire officials about restrictions and

installation inspection requirements in your area.

KEEP THIS MANUAL HANDY FOR EASY REFERRAL.

All WARNING and CAUTION statements will appear in bold

font and upper case letters: THEY SHOULD BE STRICTLY

OBSERVED.

Thank you for choosing focus fireplaces.

Appliance designation: ergofocus

Manufacturer:

Focus - Atelier Dominique Imbert

Le fort – 34380 Viols le fort – France.

Introduction

Specifications

CHARACTERISTICS

ROOF OUTLET REQUIREMENT

CHIMNEY REQUIREMENT

STRUCTURAL REQUIREMENT

CONNECTOR

FRESH AIR INTAKE

CLEARANCES TO COMBUSTIBLES

A. FLOOR PROTECTION

B. CLEARANCES TO WALLS

C. WALL CLEARANCE WITH 360° ROTATION FIREPLACE

D. WALL CLEARANCE WITH OPTIONAL

ROTATION RESTRICTOR

Installation

INCLUDED PARTS, MATERIALS AND REQUIRED TOOLS

FOR INSTALLATION

OPTIONS

ASSEMBLY DETAILS

A. STAINLESS STEEL CHIMNEY SYSTEM

PLATE SETUP AND CONNECTION

B. FLUE ATTACHMENT TO ANCHOR PLATE

C. ORDER IN WHICH TO TIGHTENING THE PLATE SCREWS

(TO SECURE PROGRESSIVELY)

D. JUNCTION SLEEVE DETAIL

E. ROTATING MECHANISM DETAIL

Operating instructions

STORAGE / USE OF FLAMMABLE LIQUIDS

GRATE

ASHES

FUEL

FIRE SCREEN

BEFORE LIGHTING YOUR FIRST FIRE

BUILDING, STARTING AND MAINTAINING THE FIRE

PROTECTIVE GLOVE

DAMPER OPERATION AND USE

Maintenance

TAKING OUT THE ASHES

CREOSOTE FORMATION AND NEED FOR REMOVAL

SWEEPING YOUR CHIMNEY

SURFACES

REPLACEMENT PARTS

Warranty

Annex

HOW TO DETERMINE IF ALTERNATE FLOOR PROTECTION

MATERIALS ARE ACCEPTABLE

ADJUSTABLE SUSPENSION PLATE

ROTATION RESTRICTOR

Specifications

•Not for mobile home installation!

•Do not connect to any air distribution duct or system!

•The authority having jurisdiction (such as municipal building department, fire department, fire prevention

bureau, etc.) Should be consulted before installation to determine the need to obtain a permit.

•Using make-shift compromises during installation can cause damage. Such installation is not covered under

focus limited warranty.

•When this room heater is not properly installed, a house fire may result. To reduce the risk of fire, follow the

installation instructions. Contact local building or fire officials about restrictions and installation inspection

requirements in your area.

CHARACTERISTICS

• Hearth 37-3/8-inch (0.95m)

diameter; weight 116 lbs

(53 kg)

• Flue diameter: 8-3/8-inch

(219mm) ;

length custom-made

• Flue weight: 10,6 lbs per foot

(16kg per meter)

• Standard plate weight

of 42 lbs (19 kg)

• 1/8-inch (3 mm) thick steel

• High heat resistant paint

• Stainless steel ball-bearing

revolving system

for a 360° rotation

• Fire screen

ERGOFOCUS

Scale 1 : 20

Note : imperial are rounded from metric

floor

(sol)

8’’ adaptor

27 3/16"

(690 mm)

67 1/8"

(1.705 mm)

29 1/8"

(740 mm)

(199 mm)

Ø 8 1/16" id

(Ø 205 mm)

Ø 8 5/8" od

(Ø 219 mm)

Ø 37 3/8"

(Ø 950 mm)

20"

(500 mm)

40 1/2"

(1040 mm)

Specifications

ROOF OUTLET REQUIREMENT

CHIMNEY REQUIREMENT

Do not connect this unit to a chimney flue serving another appliance!

Ergofocus requirement : the floor to top of chimney must be 14 feet minimum (5 m) or 17 feet (5,2 m) for an installation

less than 3 miles from the ocean or if a 30° elbow is necessary). Elbows should not be more inclined than 30°(USA) or 45°

(Canada) from vertical, and with maximum number of 2. Maximum inside + outside height : 30 feet.

The ergofocus must be connected to a chimney complying with the requirements for Type HT chimneys in the standard for

Chimneys, Factorybuilt, Residential Type and Building Heating Appliance, UL 103. For example, a class A insulated stainless

steel flue chimney system with an 8-inch minimum inside diameter.

Specifications

STRUCTURAL REQUIREMENT

CAUTION

The support of the anchor plate (roof structure, slab, etc.) Must be sized in congruence with the fireplace static and

dynamic charges. The size calculation for the support is not the responsibility of focus or its affiliates. It is your

responsibility to consult with an engineer or architect for your project.

CONNECTOR

Connectors are all non-insulated chimney parts including focus flue, focus 8’’ universal adaptor and the chimney manufacturer

finishing collar with adapter.

To avoid heat traps the chimney connector shall not pass through an attic or roof space, closet or similar concealed space, or

a floor, or ceiling.

Passage through an attic, roof frame floor, or ceiling must be done using an insulated chimney respecting all chimney

manufacturer clearances.

CAUTION

Passage through a wall or partition of combustible construction is not an appropriate installation for this

focus fireplace.

Refractory compound must be used to seal each connection.

FRESH AIR INTAKE

For optimum functioning, focus recommends a fresh air intake in the room (ideally under of the fire). We recommend

deflect-O A0684 semi rigid aluminium duct.

Minimum fresh air intake size:

This fresh air intake is compulsory

when operating venting appliances

such as kitchen hoods, permanent

air extractors or any appliances

creating an air depression in the

habitation.

IMPORTANT

FIXED

VERSION

8''

45 cm

20 cm

16'' (US)

18''(Canada)

40 cm

45 cm

PIVOTANT

VERSION

40 cm

16’’(US)

18’’(Canada)

45 cm

CLEARANCES TO COMBUSTIBLES

A. FLOOR PROTECTION

Rotating version require 16 inches (US) or 18 inches (Canada) of floor protection on all sides (360°).

Fixed version require 16 inches (US) or 18 inches (Canada) on the front and to extend 8 inches on the left and

right sides as well as for the back side.

Use of provided firebox insulator under the grate (vermiculite) is compulsory.

40 cm / 16’’ (US)

45 cm / 18’’ (Canada)

IMPORTANT

no radiant floor heating tubing under the fireplace !

pas de chauffage au sol !

non combustible surface R ≥ 0.6

surface non combustible R ≥ 0.6

combustible sub floor

sol combustible

minimum 8’

minimum 2.44 m

20’’

50 cm

33’’

84 cm

ROTATING VERSION

non-combustible

surface

R ≥ 0.6

FIXED VERSION

non-combustible

surface

R ≥ 0.6

B. CLEARANCES TO WALLS

CAUTION

The distance to a combustible wall must be maintained at 38 inches. Property damage or death can occur

if this distance is not maintained. Drywall products lined with paper such as sheetrock are combustible.

Clearances as indicated further apply.

Specifications

combustible wall

mur combustible

combustible wall

mur combustible

38’’

965 mm

360° rotation fireplace

Foyer pivotant à 360°

D. WALL CLEARANCE WITH OPTIONAL ROTATION RESTRICTOR

96 cm

38’’

48 cm

19’’

48 cm

19’’

combustible wall

mur combustible

combustible wall

mur combustible

combustible wall

mur combustible

non-rotating fireplace

foyer non pivotant

Manufacturer specifications:

• When placed close to a non-

combustible wall leave a

minimum of 4” for proper

ventilation. To avoid premature

aging of your painted walls, only

use mineral paint. With other

paints, above clearances apply.

• Fire clearance to glass (from

hearth): 31-½”.

• Fire clearance to tempered glass

(from hearth): 20”.

• Fire clearance to vinyl windows:

refer to window technical

specifications.

IMPORTANT

Clearances may only be reduced by means approved by the regulatory authority.

Specifications

Installation

INCLUDED PARTS, MATERIALS AND REQUIRED TOOLS FOR INSTALLATION

• Appliance and designated parts are the fire box, anchor plate, steel flue pipe, focus kit (protective glove, mounting

gloves, can of touch-up paint, ash removal hatch), and insulating washers.

• Required tools: drill, M8 allen key, level, screwdrivers, M12 key, scaffolding (up to underceiling height), refractory compound.

• 2 persons minimum are required for installation.

OPTIONS

• Custom ceiling cover disc (steel disc)

• Custom anchor steel plate (inclined...)

• Focus steel flue extension

• Adjustable suspension plate

• Rotation restrictor

ASSEMBLY DETAILS

A. STAINLESS STEEL CHIMNEY SYSTEM PLATE

SETUP AND CONNECTION

slip connector: same brand

as the class A insulated chimney.

adaptateur simple paroi de même

marque que la cheminée isolée

class A insulated chimney pipe

8" id - 10" od

cheminée isolée:

(200 int./250 ext.)

anti-heat loss washers

rondelles à rupture

de pont thermique

optional sub-ceiling

oblique cover disc

disque cache plafonnier

(optionnel)

focus steel flue

conduit en acier

oblique anchor plate

platine de suspension inclinée

focus 8" universal adaptor

adaptateur focus

pour conduit en 200 mm

16 " mini.

this point 3" mini.

below finished ceiling.

Ce niveau doit se trouver

75mm sous le plafond fini.

finishing collar

collier de finition

406mm mini.

B. FLUE ATTACHMENT TO ANCHOR PLATE

focus steel flue

conduit en acier

8 vis pointeaux

C. ORDER IN WHICH TO TIGHTENING THE PLATE

SCREWS (TO SECURE PROGRESSIVELY)

Installation

D. JUNCTION SLEEVE DETAIL

NOTE : The junction sleeves are provided only when the floor to

ceiling height in the room requires several focus pipe in

several parts.

(you may not find a junction sleeve on 9 feet or less

ceiling height)

E. ROTATING MECHANISM DETAIL

low part of the steel ue

bas du conduit en acier

smoke outlet sleeve

manchon de départ de fumées

washers

rondelles

nut M12 (Ø⁄’’)

écrou M12

Ø 21/40

ep. 3mm

Ø 13/27

ep. 3mm

ball bearings

butées à billes

cotter pin

goupille de sécurité

Ø ⁄’’  ⁄’’

thickness ⁄’’

Ø ½’’  ⁄’’

thickness ⁄’’

CAUTION

Screws do not sit flush when installed.

Operating instructions

CAUTION

Hot while in operation. Keep children, clothing and furniture away. Contact may cause skin burns.

STORAGE / USE OF FLAMMABLE LIQUIDS

Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or « freshen up » a fire

in this heater. Keep all such liquids well away from the heater while it is in use.

GRATE

The cast-iron grate is located inside the fireplace. It must not be removed except for cleaning, once all cinders have thoroughly

cooled. Fire must only be built on the grate.

ASHES

DISPOSAL OF ASHES

Ashes should be placed in a metal container with a tight fitting lid. The closed container of ashes should be

placed on a non-combustible floor or on the ground, well away from all combustible materials, pending final

disposal. If the ashes are disposed of by burial in soil or otherwise locally dispersed, they should be retained in

the closed container until all cinders have thoroughly cooled.

FUEL

CAUTION

Do not burn garbage or flammable fluids such as gasoline, naphtha or engine oil. Do not store the fuel within the

space heater installation clearances or within the space required for refueling and ash removal.

Only burn dry, natural, well-seasoned wood. Wood moisture content should not be more than 20%. We recommend using 2 year

dry stored wood. For the best efficiency use a covered storage.

WARNING

This fireplace has not been tested for use with doors, to reduce the risk of fire injury, do not install doors!

Tabla de contenidos

Otros manuales de Chimenea de interior de foc.us

foc.us

foc.us emifocus hublot da Manual de usuario

foc.us

foc.us optifocus 1750 Manual de usuario

foc.us

foc.us Eurofocus 951 pivotant Manual de usuario

foc.us

foc.us Meijifocus Guía del usuario

foc.us

foc.us Heterofocus 1400 Manual de usuario

foc.us

foc.us Gyrofocus Guía del usuario

foc.us

foc.us édofocus 850 d.v. Manual de usuario

foc.us

foc.us néofocus Manual de usuario

foc.us

foc.us Slimfocus sur pied Manual de usuario

foc.us

foc.us PICTOFOCUS Guía del usuario

foc.us

foc.us Grappus Manual de usuario

foc.us

foc.us Slimfocus mural Manual de usuario

foc.us

foc.us Gigafocus 1500 Manual de usuario

foc.us

foc.us agorafocus 630 suspendu Manual de usuario

foc.us

foc.us MAGMAFOCUS Guía del usuario

foc.us

foc.us Gyrofocus Instrucciones de funcionamiento originales

foc.us

foc.us Edofocus 631 DV Manual de usuario

foc.us

foc.us Hubfocus Manual de usuario

foc.us

foc.us BATHYSCAFOCUS Hublot Manual de usuario

foc.us

foc.us Meijifocus Manual de usuario

foc.us

foc.us agorafocus 850 suspendu Manual de usuario

foc.us

foc.us filiofocus 2000 mural Manual de usuario

foc.us

foc.us édofocus 630 dv Manual de usuario

foc.us

foc.us Paxfocus Manual de usuario

Manuales populares de Chimenea de interior de otras marcas

Brigantia

Brigantia 35-DVRS31N-2 Manual del propietario

Nordpeis

Nordpeis Bergen Manual de usuario

Superior

Superior BCT2536TMN Manual de usuario

Quadra-Fire

Quadra-Fire 5100I-GD-B Manual de usuario

Renaissance

Renaissance RUMFORD 1000 Manual de usuario

Lacunza

Lacunza IV-800 Manual de usuario

Baxi

Baxi 940 Instrucciones de uso

Dru

Dru Maestro 60/2 Tall RCH Manual de usuario

Diamond Fireglass

Diamond Fireglass SS-O22 Manual de usuario

HearthStone

HearthStone Windsor Bay 8830 Manual de programación

Napoleon

Napoleon ASCENT B42 Manual de usuario

Enviro

Enviro E33GI Manual de usuario

Smeg

Smeg L30 FABE Instrucciones de montaje

KEDDY

KEDDY K700 Manual de usuario

Godin

Godin 3451 Manual de usuario

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manual de usuario

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manual de usuario

Desa

Desa CCFPDFT Manual de operación

foc.us ERGOFOCUS Manual de usuario

Manuales populares de Chimenea de interior de otras marcas