Fluke MOLBLOC Manual de usuario

molbloc/molbox™

Low Mass Flow Calibration System

AFMETCAL Configurations

Installation and Operation

Manual Supplement

MOLBLOC/MOLBOX™ LOW MASS FLOW CALIBRATION SYSTEM AFMETCAL

CONFIGURATIONS

INSTALLATION AND OPERATION MANUAL SUPPLEMENT

High pressure liquids and gases are potentially hazardous. Energy stored in these liquids and gases can be released unexpectedly

and with extreme force. High pressure systems should be assembled and operated only by personnel who have been instructed in

proper safety practices.

Information in this document is subject to change without notice. No part of this document may be reproduced or transmitted in any form or

by any means, electronic or mechanical, for any purpose, without the express written permission of DH Instruments, a Fluke Company

4765 East Beautiful Lane Phoenix AZ 85044-5318 USA.

DH Instruments makes sincere efforts to ensure accuracy and quality of its’ published materials; however, no warranty, expressed or implied,

is provided. DH Instruments disclaims any responsibility or liability for any direct or indirect damages resulting from the use of the

information in this manual or products described in it. Mention of any product or brand does not constitute an endorsement by DH

Instruments of that product or brand.

DH Instruments, DH, DHI, molbloc, molbox, molstic, COMPASS and CalTool are trademarks, registered and otherwise, of DH

Instruments, a Fluke Company

VCR and Swagelok are registered trademarks of the Swagelok Company.

Viton is a registered trademark of the Dupont de Nemours Company.

Document No. 3375667

DHI Document No. 550166b

080821

Printed in the USA.

MOLBLOC/MOLBOX™ LOW MASS FLOW CALIBRATION SYSTEM AFMETCAL

CONFIGURATIONS

INSTALLATION AND OPERATION MANUAL SUPPLEMENT

Table of Contents I

Tables III

Figures IV

About This Manual 5

1. Introduction 1

1.1 system overview 1

1.1.1 the two system configurations 1

2. Installation 3

2.1 UNPACKING AND INSPECTION 3

2.1.1 Removing From Packaging 3

2.1.2 Inspecting Contents 3

2.1.2.1 MOLBOX1 3

2.1.2.2 Compass for MOLBOX software 4

2.1.2.3 caltool software 4

2.1.2.4 MOLBLOCS4

2.1.2.5 MOLSTICS 5

2.1.2.6 metering valve kits 5

2.1.2.7 AFMETCAL low mass flow system CONFIGURATION KIT 6

2.1.2.8 Custom Shipping containers 6

2.1.2.9 rpm3 6

2.2 general hardware setup 7

2.2.1 Site requirements 7

2.2.2 installation of metering valve kits 7

2.2.3 install nuts and ferrules on swage tube parts 7

2.2.4 installation of MOLBLOCS 8

2.2.5 arrangement of flow path components8

2.2.5.1 DUTs with an fittings 10

2.2.5.2 duts with swage fittings 10

2.2.5.3 connections for Dut pressure and temperature measurement 10

3. Application Notes 13

3.1 MOLBLOC RANGES 13

MOLBLOC/MOLBOX LOW MASS FLOW CALIBRATION SYSTEM AFMETCAL

CONFIGURATIONS

INSTALLATION AND OPERATION MANUAL SUPPLEMENT

3.1.1 MOLBLOC PRESSURE AND Flow ranges 13

3.1.2 gases 15

3.1.3 MOLBLOC supply pressure 15

3.2 operation 16

3.2.1 setting/checking the MOLSTIC regulator16

3.2.2 Preparing for flow measurements 16

3.2.3 setting DUT back pressure 19

3.2.4 Entry of DUT pressure and temperature measurements20

4. Warranty and Recalibration 21

4.1Warranty statement (for deliveries under f33660-99-f7000) 21

4.2 recalibration 22

4.3 Warranty service centers 22

MOLBLOC/MOLBOX™ LOW MASS FLOW CALIBRATION SYSTEM AFMETCAL

CONFIGURATIONS

INSTALLATION AND OPERATION MANUAL SUPPLEMENT

Table 1. Components List for AFMETCAL Configuration Systems.........................................................................................................................2

Table 2. Parts List for AFMETCAL Configuration Mass Flow Kit P/N 401578 ...................................................................................................6

Table 3. molbloc Usable Ranges with High Pressure Calibration.............................................................................................................................13

Table 4. Warranty Service Centers..................................................................................................................................................................................22

MOLBLOC/MOLBOX™ LOW MASS FLOW CALIBRATION SYSTEM AFMETCAL

CONFIGURATIONS

INSTALLATION AND OPERATION MANUAL SUPPLEMENT

Figure 1. Arrangement of Flow Path Components ........................................................................................................................................................8

Figure 2. AFMETCAL Kit Downstream of molstic ......................................................................................................................................................9

Figure 3. Connection of RPM3 and Temperature Measurement Device for DUT with Back Pressure ............................................................11

Figure 4. AFMETCAL Configuration molbloc Label..................................................................................................................................................13

MOLBLOC/MOLBOX™ LOW MASS FLOW CALIBRATION SYSTEM AFMETCAL

CONFIGURATIONS

INSTALLATION AND OPERATION MANUAL SUPPLEMENT

This manual provides information specific to installing and operating the AFMETCAL molbloc/molbox

system configurations purchased under contracts F33660-99-F700 and F33660-00-F7007 and is defined

by NSN 6680-01-466-2062. It is intended to be used as a supplement to the molbox1 molbloc

Terminal (Ver. 5.00 and higher) Operation and Maintenance Manual, RPM3 Operation and

Maintenance Manual and COMPASS for molbox User’s Manual Version 4.00. The molbox1,

molblocs and COMPASS for molbox software provided in AFMETCAL system configurations are

standard products identical to the commercial versions covered in the standard product manuals.

Manual Conventions

(CAUTION) is used throughout the manual to identify user warnings and cautions.

(NOTE) is used throughout the manual to identify operating and applications advice and additional explanations.

[ ] indicates direct function keys (e.g., [UNIT]).

< > indicates molbox1 screen displays (e.g., <1yes>).

MOLBLOC/MOLBOX LOW MASS FLOW CALIBRATION SYSTEM AFMETCAL

CONFIGURATIONS

INSTALLATION AND OPERATION MANUAL SUPPLEMENT

MOLBLOC/MOLBOX™ LOW MASS FLOW CALIBRATION SYSTEM AFMETCAL

CONFIGURATIONS

INSTALLATION AND OPERATION MANUAL SUPPLEMENT

Introduction

system overview

An AFMETCAL configuration molbloc/molbox mass flow calibration system is made up of standard

molbloc/molbox system components plus a special hardware kit. The kit includes this manual and

several hardware items to provide pressure regulation and interconnections to devices under test (DUTs).

These hardware items are selected to allow calibration of flow devices as defined by AFMETCAL,

specifically, gas flow meters with 1/4 in. tube (Swage) or AN4 type fittings used at various pressures

ranging from zero to 50 psig. The system’s maximum calibrated flow rate is 40 slm.

There are two different AFMETCAL configurations. One is the basic configuration. The other is the

calibration exchange system. Their differences are summarized below in Section 1.1.1. Table 1 lists the

specific components included in each configuration.

the two system configurations

BASIC AFMETCAL CONFIGURATION

The basic configuration includes a molbox, molstics and five molblocs to handle flows up to 40 slm. COMPASS for molbox software,

metering valve kits and the AFMETCAL Configuration Kit are also included in the basic configuration. This is the system

configuration which will be in regular use in the PMEL labs, and is specifically defined by NSN 6680-01-466-2062.

CALIBRATION EXCHANGE SYSTEM

This system is intended for delivery to AFMETCAL for temporary use at the various PMELs while each PMEL’s system is being

serviced or recalibrated. The exchange system is identical to the basic configuration above with two exceptions:

•The exchange system is delivered with CalTool software instead of COMPASS software to provide AFMETCAL with the

ability to recalibrate molblocs.

•Two custom shipping containers are included to facilitate the shipping of the exchange and PMEL systems back and forth for

recalibration.

MOLBLOC/MOLBOX LOW MASS FLOW CALIBRATION SYSTEM AFMETCAL

CONFIGURATIONS

INSTALLATION AND OPERATION MANUAL SUPPLEMENT

Table 1. Components List for AFMETCAL Configuration Systems

QUANTITIES

DHI PART NO. DESCRIPTION BASIC EXCHANGE

401265 molbox1 Terminal 1 1

3069609 (401182) 10 (1E1) sccm molbloc 1 1

3069611 (401183) 50 (5E1) sccm molbloc 1 1

3069648 (401198) 500 (5E2) sccm molbloc 1 1

3069037 (400483) 5 (5E3) slm molbloc 1 1

3069524 (401042) 30 (3E4) slm molbloc 1 1

3069773 (401318) Dual Low Flow molstic 1 1

3069712 (401244) Single Mid Flow molstic 1 1

3069764 (401317) Dual Mid molstic 1 1

3069786 (401319) Low Flow Metering Valve Kit 4 4

3069799 (401320) Mid/high Flow Metering Valve Kit 1 1

3350751 (401578) AF Config Mass Flow Kit 1 1

FAM0003 RPM3-A0100b Pressure Monitor 1 1

2758335 (100847) RS232 Cable 1 1

3069666 (401211) COMPASS Software Ver. 4.0 1

3119808 (102848) CalTool Software 1

NPN Custom Shipping Container 2

This manual is a supplement to the molbox1 and COMPASS for molbox manuals. For molbox1 system

specifications, refer to Specifications section in the molbox1 molbloc Terminal (Ver. 5.00 and higher) Operation

and Maintenance Manual.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Brújula de otras marcas

Silva

Silva EXPLORER 203 Manual de usuario

Quechua

Quechua C Quechua 400 Manual de usuario

Brunton

Brunton 85R Manual

Brunton

Brunton 54lu Manual de usuario

Raymarine

Raymarine ST40 Manual de usuario

Advanced Navigation

Advanced Navigation GNSS Compass Manual de usuario

Brunton

Brunton 9020G Guía de configuración rápida

Furuno

Furuno SC-30 Manual de usuario

PNI

PNI V500 Manual de usuario

Suunto

Suunto KB-14/360 Manual de usuario

Conrad

Conrad 67 13 02 Manual de usuario

Brunton

Brunton NOMAD V2 PRO Manual de usuario

Bushnell

Bushnell Digital Navigation 70-0002 Manual de usuario

Dakota Digital

Dakota Digital Odyssey ODY-17-1 Manual de usuario

Brunton

Brunton 16B Braille Manual de usuario

Freestyle

Freestyle TOUCH COMPASS Manual de usuario

True North

True North Revolution Manual de usuario

TECHTRAIL

TECHTRAIL Trailhead Manual de usuario