Flowtoys Modular System Manual de usuario

QUICK START GUIDE: THINGS TO KNOW BEFORE YOU FLOW

1. Do not use glowsticks or WD-40 with tubing. While polycarbonate is very strong, it breaks down

in the presence of certain esters, including those produced by chemical glowsticks, mineral spirits and

WD-40. Do NOT put chemical glowsticks into the tubes, otherwise they can become brittle and

shatter. We recommend lubricating the ends of your tubes with a touch of petroleum jelly.

2. Be careful when using your owtoys in the presence of sand or grit!

Sand and grit can get inside your caps and connectors and make them dicult to use. If you’re using

owtoys in a sandy area, blow out/clean your caps and connectors of sand before attaching them to

the tubing. If your caps and tubes feel gritty, clean them and apply a bit of vaseline for lubrication.

3. Make sure all caps and connectors are fully secured before use! Check that the buttons in your

caps and connectors are fully clicked into the holes of the tubes.

4. Cleaning your owtoys. If your owcaps, connectors, crystal cases or owmass get dirty after

hours of practice in the park, owing in the forest or rockin’ it on a danceoor, clean them with soap

and warm water, or put them in the wash with your laundry: air-dry, no heat!

LIFETIME WARRANTY

Flowtoys are designed to last you a lifetime, but nothing is indestructible,

so we provide this warranty to enable you to freely nd your ow*.

If you manage to break a owtoys product, we have a policy of free

replacement on damaged non-electronic parts and defective electronics,

and 50% o replacement on broken electronics. If the tips in this guide do

not keep your owtoys working for years to come, please contact us!

* Flowtoys reserves the right to refuse coverage to anyone abusing this warranty.

Please contact us before sending in your product, or it may be returned to sender.

Modular System Guide

features

operating instructions

troubleshooting

inspiration

Combining versatile owtoys LED light units – the owlight and the capsule light – and a

series of click-in caps, connectors and tubes that are interchangeable, the modular system

enables the creation of almost any illuminated prop imaginable.

Gone are the days of wondering how to check in our 5’stas for travel, or deciding which

owtoys to bring to an event. Now with just a few lights, tubes, caps and leashes, you can

have 4’double stas that quickly transform into a contact sta, a couple of 3’stas, clubpoi,

swinging clubs, chucks and more, and everything ts in a backpack!

The world just became a little more awesome for us, because of the versatility, creativity

and fun the Flowtoys Modular System enables. We hope that it will bring more ow and

more awesome to your life!

high performance modular system - endless possibilities for ow

FLOWTOYS MODULAR SYSTEM - COMPONENTS

FLOWLIGHT-FS: World’s most revolutionary LED glowstick. Beautifully sculpted poly-

carbonate shell refracts full spectrum LEDs. 40 adjustable modes with many bright

and beautiful color and pattern options, kinetic awareness, accelerometer response,

battery and charge level indicators and more. 1 rechargeable AAA provides 3-27

hours run-time. Connect as many as you like to ll your tubes with lights.

CAPSULE LIGHT: Incredibly strong polycarbonate shell diuses 12 LEDs into a single

pixel of a million colors. MicroUSB rechargeable Li-ion battery for 6-77 hour run-time!

Link up to 2 together. Intuitive one-button interface and “kinetic awareness” enable

you to select and adjust a virtually innite variety of amazing light patterns.

1”TUBES: Highest quality polycarbonate extrusion, transparent yet virtually bullet-

proof, connects to caps and connectors via snap-button holes. Available in a variety

of interchangeable lengths for instant reconguration.

STAFF CONNECTOR: Polycarbonate joints with integrated snap buttons that se-

curely connect 2 tubes. Built-in suspension cushions owlights for high impacts. Plus

its highly-engineered structural design looks so cool ...

CORD CONNECTOR: Cord connectors enable a strong and reliable connection

between your owtoys tubes and leashcord. Screw holes align with holes in tubing

for a very secure connection.

FLOWCAP: Thick, soft, durable silicone body. Inner polycarbonate snap-cap buttons

snap securely onto tubes and release with a rm twist. Built-in button compatible

with capsule lights; connects to owlights with adaptor.

POD SHELL: Beautiful, thick, super-soft and durable silicone, built-in button

compatible with capsule lights, strategic internal petal-ribs provide structure and

focus mass at the bottom for great rotational inertia. Possible to connect to ow-

lights, but not recommended. Pod shells attach to tubes with a friction t - please

read instructions and use caution.

FLOWMASS: These translucent crystalline-looking weights add more inertia to your

ow and optimize the balance of your owtoy. They can be added to crystal cases

and owtoys 1” tubing. Add two or more if you like your tools heavy!

KNOB-LEASH: Adjustable integrated leash with knob handle and minimal hardware.

Made with owcord—the rst cord designed for poi spinning, and comfortable knob

handles. Highest quality for durability, aordability, comfort and endless ow!

LINKED CORD CONNECTOR: Two cord connectors linked by a user-adjustable cord

that forms a exible connection between 2 tubes. Allows you to create chucks, tri-

sectionals, cubes, tetrahedrons, ails and more.

KNOB-LEASH W/ CORD CONNECTOR: A pair of knob-leashes with knob handles,

adjustable owcord, and cord connectors.

DART CORD CONNECTOR: A 10’ length of owcord with a single cord connector to

create a martial owdart.

More components, details and info available on www.owtoys.com

CAPS :: FLOWCAP

Your tube-based props come standard with owcaps. The owcap is compatible with both

owlights and capsule lights, and securely clicks into any owtoys 1”polycarbonate tubes.

FLOWTOYS MODULAR SYSTEM - INSTRUCTIONS

INSTRUCTIONS FOR LIGHTS

Modular system props are compatible with both owlights and capsule lights - instructions

for your lights are included in a separate manual with your prop.

CAPS :: POD SHELL

Pod shells are intended for use with capsule lights only. Can be used as caps for sta ends.

Pod shells provide great rotational inertia for stas and baton ends, but are not recommend-

ed for other tubing-based props like owpoi, rope darts, chucks and clubs.

INSERTING CAPSULES INTO POD SHELLS:

Capsules MUST have their C-ring installed before inserting into pod shell. Insert capsule

with C-ring into the bottom of the pod shell rmly. Check button for normal operation. If the

button is dicult to press, check that the capsule is all the way inside the shell and the C-ring

is properly installed on the capsule. Also check that there is not a C-ring already in the pod!

ATTACHING POD SHELL ONTO TUBE:

The pod shell attaches to the tube with a friction t. Push the pod shell over the tube rmly,

ensuring the plastic tube is between the capsule and the silicone tube inside the pod that

holds the capsule in place.

Be aware - the tube must be clean and the edge of the silicone that holds the capsule must

cover the holes in the tube for a secure t. Silicone does not stretch out, warp, or relax like

other plastics, and as long as it is installed correctly the pod cannot y o during use. You

have been warned. We will not replace parts that go ying due to inadequate connection!

DETACHING/ATTACHING FLOWCAPS TO TUBES:

• To detach, twist rmly to release the buttons and pull.

• To attach, place cap over tube, push and twist until snap-but-

tons click into the holes.

ATTACHING/DETACHING FLOWLIGHTS TO FLOWCAPS:

• Push the narrow “head” of the owlight into the adaptor, then

insert owlight+adaptor into the owcap.

• Twist until the adaptor clicks into place. The sides of the light

should align with the buttons in the cap.

• To remove the adaptor with the light, push the button on the

cap while twisting the light.

• To leave the adaptor in the cap, pull light out while gripping

the cap.

Tip: If your owcaps feel squeaky when attaching to the tubing, you can lubricate the connection

with a tiny bit of grease - often the oils from your hand are enough to remove the “stiction” between

the plastics, and give you a nice smooth connection.

ATTACHING CAPSULES TO FLOWCAPS: Your capsules should not have a C-ring in-

stalled. Insert capsule into owcap button side rst. Twist until it settles into place. The

“shoulders” at the end of the capsule must be aligned with the buttons in the cap for it

to t in the tube. You’ll feel a small wiggle - this is normal.

*click!*

INSTALLING FLOWMASS: Flowmass is slightly tapered with more material on one end—

make sure the heavier end is installed at the far end of your prop, where it counts.

Adding mass to a crystal case: Thread the leash through the mass. Hold leash with one

hand and pull the mass along the length of the case with your other hand until the mass is

in place. If this is dicult, try hooking your leash onto a doorknob or other secure object.

Do not lubricate mass, as this can cause it to slip o.

Positioning the mass on a crystal case: There is a circular symbol on the mass that should

align with the button facet on the crystal case, which also aligns with the owlight button.

This allows you to feel for the button from the outside, and creates the most aesthetically

perfect positioning of the mass with respect to the crystal case.

Adding mass to tubes: Apply a little bit of vaseline/petroleum jelly to the inside surface of

the mass and slide the tube through it. Ensure there is enough clearance at the top for your

owcaps to click in properly and securely.

Tips for using the sta connectors:

1. Rub the connectors and inside of the tube with your ngers, the natural oils from your hands

will lubricate the connectors and tube just enough to make for a smooth t.

2. if you twist it one way and it seems tight, don’t force it. Twist it the other way and see if it’s

supposed to release that way instead.

3. Avoid having sand/grit fall between the connector and the tube. Clean as needed.

STAFF CONNECTOR TO TUBE:

• To attach, insert the sta connector into a tube, twist until connector buttons click

into the holes securely.

• To detach, twist the tubes in opposite directions to disengage the buttons from

the holes then pull.

The buttons are directional:twisting one way will release one half of the connec-

tor, while twisting the other way releases the other half. Try not to twist them out

the wrong way as this can weaken or break the part.

LINKING 2 CAPSULES

• Remove the o-rings from the leash-port (battery side) of two capsules.

• Pry open one shell enough to insert the link then reinstall the O-ring.

• Roll the second capsule’s O-ring over the rst’s, then connect the second capsule to

the link and roll the O-ring onto it. It is also possible to install and remove the link by

prying and holding the capsule open with the O-rings in place - if you have strong

ngers! Only two capsules can be connected - both buttons should face out.

Compatibility: Capsule links are only compatible with capsule shells since mid 2013.

Some older versions do not separate in a way that would allow this link to work prop-

erly. Please check our web support page for details. If your capsule is not compatible,

CONNECTING FLOWLIGHT TO FLOWLIGHT: If you have two or more owlights in

one tube, you will need to attach the opposite ends of the owlight to each other for

the lights to t properly, and slide in and out of the tubes properly.

Be sure to click them together and apart sideways (laterally as shown in the picture),

NOT up and down in the direction of the pivot (vertically), as this can cause splitting

at the seam and loosen the connection.

INSTRUCTIONS FOR POI, DARTS & OTHER LEASH-BASED PROPS

KNOB-LEASH + CORD CONNECTOR

Your tubing-based poi and darts come with an integrated leash system made of“owcord” - the

rst cord engineered for poi spinning with perfect smoothness and optimal give.

Your knob-leash comprises a pair of knob handles w/ a washer and extra owcord to adjust your

leash length, and connects to tubes via a cord connector with 2mm hex head screws.

ADJUSTING THE LENGTH OF YOUR KNOB-LEASH

Adjusting your leash to t your body and style is an easy and important step to optimizing your

poi experience.

Loosen the knot on the end with the extra cord, and move the position of the knot to lengthen

or shorten your leash. Test the length and adjust as needed - a popular length is from hand to

shoulder. Tighten the knot and nish your leash (see instructions below). The result is a high

performance leash with minimal hardware or knots.

Finishing the leash end:

• Tighten the knot. Cut excess cord o with scissors.

• Melt the end of the knot with a lighter and while the

end is still soft/melted, use the edge of the lighter to

atten and shape the end of the knot onto the rest of

the knot. This ensures the knot will not come undone.

Tip: if the melted plastic sticks to the lighter, it’s too hot. Wait a second before shaping it.

INSTALLING FLOWCORD ONTO CORD CONNECTORS

Your tubing-based poi or dart should come with cord connectors and leash already installed.

You should NOT need to remove the connectors, but if you need to re-install:

• Melt end of cord (to prevent fraying). Push + twist cord to thread it through cord connector.

• Slide a small washer onto end of owcord (you can use pliers to help pull it through).

• Tie a simple overhand knot below the washer – don’t tighten it yet! Check and conrm how

long you’d like your leashes to be.

• Once you nd your ideal length, tighten the knot, and trim o excess cord with a pair of

scissors, leaving 1/8”or 3mm extra to melt. Finish leash end (instructions above).

• Snug the washer up against the knot.

INSTALLING CORD CONNECTOR TO TUBE

• Pull the knot and washer up and inside the connector before installing onto your tubes.

• Insert connector into tube. Align screw holes in the connector with holes on your tube. If

o-rings are sticking to the wall of the tube, use your nger to apply a little bit of petroleum

jelly or any other safe grease (lip-balm, hand-lotion, etc.) to the inside of the tube.

• Once the cord connector is seated in the tube, holes aligned, use the 2mm hex head screws

and 2mm hex key provided to secure the cord connector to your tube.

• Be sure not to strip the threads by over-tightening – this could cause them to fail later.

SAFEGUARDS AND PRECAUTIONS

This guide outlines basic safeguards in using your owtoys. The precautions and instructions

presented cannot cover all possible circumstances and situations that may occur. In using any

owtoy, the user understands that common sense and caution cannot be built into the product,

and must be provided by him/herself. Please read all instructions before use.

1. Flowtoys are intended for practice, play, performance and movement meditation. Do not use

for any other purpose.

2. Do not use products under the inuence of alcohol or drugs. Consult prescription labels to de-

termine if a particular drug would impair your judgment or reexes. If so, do not use this product.

3. Stay alert and use common sense. Do not use this product when tired or distracted. Be aware

when in the presence of fragile or breakable objects.

BEFORE USE: Check for damaged parts before using any product. Ensure caps, connectors and

battery doors are fully secured. Most owtoys are made of individual pieces that can separate

during use if not properly assembled.

GENERAL CARE: Repair or replace damaged or worn parts before use. Do not use damaged

products.

REGULAR MAINTENANCE: Maintain all Flowtoys products with care. Store in a clean, dry envi-

ronment. Avoid over-exposure to sunlight: UV rays compromise the integrity of plastics.

UNAUTHORIZED COMPATIBLE PRODUCTS: Our products should not be combined with

products or parts from other manufacturers, unless specically authorized by us and such other

manufacturers. Any unauthorized product combination may void the warranty of our products

and other manufacturers’products.

Warning: This product is not intended for use by children age 14 and under.

2017.11

Don’t ask yourself what the world needs.

Ask yourself what makes you come alive, and then go and do that.

Because what the world needs is people who have come alive. - Howard Thurman

To the illuminated mind the whole world sparkles with light. - Ralph Waldo Emerson

Thank your parents.

A pint of example is worth a gallon of advice.

If you have an idea, make it happen. Ideas won’t work unless you do.

Do or do not ... there is no try. - Yoda

Drink lots of water. Stretch. Breathe.

I’m trying to free your mind. But I can only show you the door.

You’re the one who has to walk through it. - Morpheus

DO GOOD. BE AWESOME. MAY THE FLOW BE WITH YOU!

Visit owtoys.com for more information, inspiration, videos, instructions and tips.

Tabla de contenidos

Otros manuales de Equipo de iluminación de Flowtoys

Flowtoys

Flowtoys Full Vision Lumina Twirl Baton Manual de usuario

Flowtoys

Flowtoys Capsule 2.0 Manual de usuario

Flowtoys

Flowtoys Crystal Manual de lista de piezas

Flowtoys

Flowtoys Full Vision Contact Wand Manual de usuario

Flowtoys

Flowtoys Vision Clubs Manual de usuario

Flowtoys

Flowtoys Full Vision Flower Stick Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario