FLIR HM-Series Manual de usuario

432-0004-31-12 Rev 100 Jan 2013

HM-Series Quick Start Guide

Power Button – The HM-Series camera has 3 power modes: On, Off, and

Standby.

• On - Takes approximately 90 seconds (during bootup there is a

fast-flashing red LED on the eyepiece display).

• Standby - After the camera is on, pressing the Power button will

toggle the camera between On and Standby mode. (In Standby

there is a slow-flashing red LED on the eyepiece display).

• Off - Push and hold the power button for 8 sec. to turn off.

Capture Button – Some models only; take snapshots (press and

release) or video clips (press and hold) to the SD memory card.

Display Brightness – Toggle through five brightness settings.

White/Black Hot/Instalert – In White Hot mode, hotter items appear as white

or light grey. In Black Hot, hotter items appear as black or dark grey. In Instalert,

hotter items in a scene are highlighted in red.

2× Zoom –Some models only; causes the image to zoom to 2X.

Diopter Control – Adjust the diopter setting for the sharpest image in

the viewfinder.

PowerCapture2x zoom

Display

Adjustable

Diopter

Eyepiece

Lens Cap

Brightness

White hot/

Black hot/

Marine Red

Guide_Card.fm Page 1 Friday, January 25, 2013 2:54 PM

432-0004-31-12 Rev 100 Jan 2013

HM-Series Quick Start Guide

Installing the Batteries and SD Card

The batteries must be installed and charged before using your camera.

Install your SD card.

1. Remove the small SD card door.

No tools are required.

2. Install the SD card.

3. Loosen the four captive screws securing the

battery cover.

4. Remove the battery cover by grasping the front

edge where the SD card door was removed.

5. Install the batteries as shown.

6. Snap the SD card door back into place and re-

install the battery cover—it only fits one way.

Charging the Camera

The batteries in the camera must be charged prior to their first use.

1. Connect the Hot Shoe to your camera.

2. Ensure that the plug is fully seated in the Hot

Shoe.

When charging correctly, the charging indicator

will be lit yellow and will blink green for one second

within about 35 seconds.

The charging indicator will continue to blink at

decreasing intervals until the batteries are fully

charged.

When fully charged, the charging indicator will be

lit solid green. The initial charge time is

approximately 4 hours.

www.flir.com

Grasp SD card

Battery

cover

door edges

and pull

+

–

+

–

–

+

–

+

Plug from power adapter

Charging

indicator

Solid

green

Guide_Card.fm Page 2 Friday, January 25, 2013 2:54 PM

Otros manuales para HM-Series

2

Tabla de contenidos

Otros manuales de Cámara térmica de FLIR

Manuales populares de Cámara térmica de otras marcas

Hikmicro

Hikmicro B20 Manual de usuario

BST

BST BT-72 Manual de usuario

CBC

CBC EN7-S02T Manual de usuario

Satir

Satir YRH600 Manual de usuario

TESTO

TESTO 882 Manual de usuario

TECPEL

TECPEL TIG-320 Manual de usuario

SKF

SKF TKTI 21 Manual de usuario

TESTO

TESTO 885 Manual de usuario

InfiRay

InfiRay AT300 Series Manual de usuario

InfiRay

InfiRay AT Series Manual de usuario

Videotec

Videotec MAXIMUS MVXT Manual de usuario

Guide Sensmart

Guide Sensmart D384M Manual de usuario

NBN

NBN FLIR A6 Series Manual de usuario

WORKSWELL

WORKSWELL SAFETIS Manual de usuario

Major tech

Major tech MTi11 Manual de usuario

COHU

COHU 5935-1000/T100 Manual de usuario

MikroScan

MikroScan 7600PRO Manual de usuario

Chauvin Arnoux

Chauvin Arnoux C.A 1879 Manual de usuario