Flight Model Courage-8 40 Instrucciones de uso

SPECIFICATION:

Wing󴖦span：57in/1448mm

Wing󴖦area：36.1sq.dm

Length：44.3in/1125mm

Flying󴖦weight:2100-2350g

Engine:2cycle󴖦40-46

Radio：4channels󴖦4servos

CONSTRUCTION GUIDE

1 Epoxy the 2 identical plywood wing joiners together.

Cut out aileron servo opening on top of wing panels.

2 Looking forward towards the leading edge, the wing should form a "V" when assembled.

The top of the wing has lettering on it.

3

4Install the main landing gears as shown. Attach with the screws that you should have purchased

(No. 2 by 1/2")

Next, glue the hardwood torque rod covers in place. They have a notch in them to allow for

movement of the aileron rod. You may have to enlarge the holea little to allow for proper

movement.

The wing is joined together by inserting one plywood dihedral braces into each wing panel and

then epoxying into place.You may want to check the fit first, before gluing. Make sure that the

wing panels butt together closely so that the dihedral angle is correct. Before gluing, you can

cut into the wing panels a hole large enough to accommodate the plywood servo mount.This mount is

2*3/8" by 1*9/16" and fits onto the dihedral brace, it is supported by two pieces of plywood

1*1/16" by 1*1/16" one which should be glued to the dihedral brace after the wing is joined

together.(It protrudes through the top on the low wing versions.) Apply a liberal amount of epoxy

to the brace and to the wing panels when joining together, wipe off any excess, and then tape the

panels together to insure a good glue joint. Once together, glue in the servo mount. A piece of

clear plastic tape is wraped around the center section of the wing to seal the glue joint.

5

6Assembly the fuel tank as shown. Apply a bead of silicone sealant around the fuel tank cap as

shown when installing it into the fuselage.

Hook up noes wheel steering pushrod and route through housing which is installed into servo area.

The nose gear is incorporated into the engine mount. The steering cable is routed along the left

side of the fuselage and attached to rudder servo.Check the diagram for assembly.

7Offset the engine by two degrees to the right. Drill four 7/64" holes for the engine. Use the

selftapping screws supplied. Install the nose wheel assembly at this time.

8The elevator must be attached to horizontal stabilizer using 3 hinges. You may have to trim the

elevator to fit the stabilizer. The stabilizer should be flush with rear of the fuselage as per

the diagram.

IT IS ESSENTIAL THAT THE STABILIZER AND THE RUDDER ARE 90 DEGREES TO EACH OTHER, AND THAT THE

WING 15 PARALLEL TO THE STABILIZER.

A good way to check the alignment is to first attach the wing to the fuselage. Slide the

stabilizer into the fuselage, making sure that it is centered. Place the airplane on a table or

some steady surface and then stand back. Look at the airplane from the front, the engine would be

the closest thing to you. Stand back about 8 feet and try to have your sight level with the

engine. It will be immediately apparent if the wing is not parallel with the stabilizer.

Trim the fuselage to fit the stabilizer properly. Fill any gap with scrap wood or epoxy.

Glue vertical stabilizer into the fuselage and onto the stabilizer. The rudder attaches to the

vertical stabilizer with two hinges.

9

The wing is mounted to the fuselage by using (80)#64 rubber bands.

The bands are designed to pop off during hard langings and thus help prevent major

damage.Four rubber bands are needed per side.

Two wooden dowels are inserted through the fuselage to hold the wing in place. No.62

rubber bands are used to attach the wing.At least 4 rubber bands should be used on each

side.

Wrap the bands around the wooden dowels as shown above.This design is to allow for those

not-so-perfect landings that come with learning how to fly.

At this time be certain that the aileton servo is connected to the receiver,otherwise the

wing will need to be removed later to connect it.

10

The pushrods are made of wood and are to be assembled as shown in the drawing.

Attach the rod to the servos with a anap keeper, the same as the aileron pushrods. The

throttle pushrod is just a length of 3/64" wire sliding in the preinstalled tube. Be sure

to adjust it so that you have full movement of the carburetor without stalling the servo.

Check the size of the servo holes in the fuselage servo tray; alter as necessary. epoxy

into the fuse, and install the servos. Tutn on the system and check the operation of the

servos; they shuold all work without interfering with each other or the fuse.

Attach the rod to the horn, set the surface and the servo to neutral, and mark the length

on the ftont rod. Remove the rod, make a rightangle bendin the wire, and cut off the

escess.

The bent rods included are for the servo ends and the threaded todsare for the back ends.

After mounting the control horns on the rudder and elevator (use the squares of clear

plastic between the horn and the surface, and between the nut plate and the surface) you

11 The canopy is installed as shown using epoxy glue.

12 The amount of the travel needed for the variour control surfaces is shown.

Otros manuales de Juguete de Flight Model

Flight Model

Flight Model M089 F3A 68.5IN Manual de usuario

Flight Model

Flight Model F-4U Corsair 100CC Instrucciones de operación

Flight Model

Flight Model Kelly F1 60 Instrucciones de operación

Flight Model

Flight Model F126 PITTS S12 94.5" Instrucciones de operación

Flight Model

Flight Model Mini Excellence Manual de usuario

Flight Model

Flight Model CRICRI 70 Instrucciones de operación

Flight Model

Flight Model SU-29 50CC Manual de usuario

Flight Model

Flight Model F043 Super Decathlon Manual de usuario

Flight Model

Flight Model F114 Sbach 342 20cc Manual de usuario

Flight Model

Flight Model ZERO A6M5B Manual de usuario

Flight Model

Flight Model YAK-55 50CC Manual de usuario

Flight Model

Flight Model F124 MXS-R 30-35CC Manual de usuario

Flight Model

Flight Model Taylorcraft-90 Instrucciones de operación

Flight Model

Flight Model F055 Butterfly-3D Instrucciones de operación

Flight Model

Flight Model F080 Zero Flighter 91" Manual de usuario

Flight Model

Flight Model EXTRA-330SC 60CC Manual de usuario

Flight Model

Flight Model YAK-54 35-40CC Instrucciones de operación

Flight Model

Flight Model F127 Zlin-42 60 Instrucciones de operación

Flight Model

Flight Model F153 EXTRA 300 125" Instrucciones de operación

Flight Model

Flight Model F113 YAK 54 20CC profile Manual de usuario

Flight Model

Flight Model Extra-330 57" EP Instrucciones de operación

Flight Model

Flight Model Apollo 90 Manual de usuario

Flight Model

Flight Model F130 Nemins-60 Instrucciones de operación

Flight Model

Flight Model Extra-330 30-35CC Instrucciones de operación

Manuales populares de Juguete de otras marcas

marklin

marklin 37321 Manual de usuario

Canon

Canon PAPER CRAFT Manual de usuario

GREAT PLANES

GREAT PLANES Pitts M-12S Manual de usuario

NOCH

NOCH 14261 Manual de usuario

Hausler

Hausler 450 SE V2 Manual de usuario

Dynaflite

Dynaflite Daydream Manual de usuario

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manual

Kenner

Kenner Batman 63651 Manual de usuario

LEGO

LEGO 8527 Manual de usuario

iKarus

iKarus ECO 8 Manual de usuario

Multiplex

Multiplex EasyStar II Manual de instrucciones

Walkera

Walkera 38 Manual de instrucciones

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manual de usuario

MD

MD MXION SWD Manual de usuario

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manual de usuario

marklin

marklin 39671 Manual de usuario

Meccano

Meccano 15103 Manual de usuario

LEGO

LEGO TECHNIC 8735 Manual de usuario