Fleetworks FLTW-7634 Manual de usuario

!!!!!!!!!!INSTALLATION!INSTRUCTIONS!

2009-2012 RAM Truck Rear Vision Parkline Camera with RCA and

Factory Display Harnesses (Kit part number FLTW-7634)

Kit Contents:

Chassis Harness

1 bubble bag containing:

Tailgate Handle Camera

1 bag containing:

2 pieces ½” glued heat shrink tube

These instructions

Tools & Supplies Required:

Socket Wrench or Socket Driver

Plastic Trim Removal Tool

Phillips and Flat Blade Screwdrivers

Power Drill

Center Punch

Heat Shrink Tubing (recommended) or Electrical Tape

Soldering Iron and Solder (optional) or T-taps

Heat Gun

Corrosion Inhibitor (recommended)

Wire Ties (recommended)

Note: We strive to provide accurate and up-to-date installation instructions.

IMPORTANT: Verify kit contents are complete against list above before beginning installation.

Preparation

1. Ensure all lamps and accessories are OFF.

2. Ensure ignition switch is in the OFF position.

3. Loosen negative battery cable bolt. Remove

negative battery cable from terminal and position

away from battery

4. Wait one (1) minute prior to working on vehicle to

assure SIR roof rail airbag system has been disabled

for your safety

Install Camera into Tailgate

5. Lower Tailgate and (if equipped) remove plastic

Tailgate Protector.

6. Remove the Tailgate Access Panel. (Figure 1)

Figure 1

7. Disengage (2) plastic Latch Rod Retainer Clips using

your fingers. (Figure 2)

Figure 2

8. Remove Tailgate Handle using a Socket. (Figure 3)

Figure 3

9. Remove lock cylinder from original Tailgate Handle.

Remove Tailgate Lock Cylinder Retaining Clip and

then Tailgate Lock Cylinder and reinstall into

supplied Tailgate Handle Camera. (Figure 4)

Figure 4

10. Route Tailgate Handle Camera connector down

through Tailgate Handle opening then out through

the hole at bottom of Tailgate.

11. Pull Tailgate Handle Camera connector through the

pass-through hole in the rear of the pickup box.

12. Reinstall Tailgate Handle.

13. Reattach (2) plastic Latch Rod Retainer Clips using

your fingers.

14. Reattach Tailgate Access Panel.

15. (If equipped), reinstall plastic Tailgate Protector.

16. Close Tailgate.

Chassis Harness Pass Through

17. Using a Plastic Trim Removal Tool, remove Left

Instrument Panel Outer Trim Cover. (Figure 5)

Figure 5

18. Remove driver side door sill cover/kick panel cover.

(Figure 6)

Figure 6

19. Pull back driver side floor carpet.

20. Look for existing grommet or hole to run chassis

harness through. If no existing hole is available make

sure that there is nothing on the back side of pass

through opening (wiring, parking brake cable, etc),

mark center with a Center Punch and use a 1/2” Drill

Bit to make a pilot hole. (Figure 7)

Figure 7

21.Recommended: Apply a corrosion inhibitor to the

Chassis Harness pass through hole. (Figure 8)

Figure 8

22.

Insert RCA connector end of supplied Chassis

Harness through cab floor into cab.

(Recommended: Silicon or Grommet to seal off

hole.)

Connect & Secure Chassis Harness

23. Plug the RCA connector end of the supplied Chassis

Harness into Video In your display.

24. Route supplied Chassis Harness along existing

chassis harness toward rear of vehicle, staying clear

of body mounts. (Figure 12)

Figure 12

25. Connect supplied Chassis Harness to Tailgate Handle

Camera harness. Use supplied glued heat shrink

tube over RCA and Power connector to create seal

between chassis and camera harness. (Figure 13)

Figure 13

Connect Chassis Harness to Vehicle Wiring

26. Connect the supplied Chassis Harness Red and Black

leads as directed in the chart appropriate for your

vehicle below.

Chart A:

Aftermarket display / Factory NAV

Color

Polarity

Function

Location

Red

(+)

Ignition

Splice to

pink/green wire in

Instrument Panel

connector pin 16

(Figure 1)

Black

(–)

Ground

Chassis ground

(Figure 2)

Figure 1

Figure 2

27. If using this kit with the factory 8.4” touch

screen, follow Steps 35 through 49 and Steps

52 through 54 below.

28. If using this kit with an aftermarket mirror /

display / NAV display, connect Chassis

Harness male RCA to “Camera IN” on the

aftermarket mirror / display/ NAV display.

NOTE: A RCA extension may be required.

Proceed to Step 46.

29. Connect supplied 8.4” Touch Screen Jumper Harness

to RCA end of supplied Chassis Harness.

30. Use of this camera with the factory Ram 8.4” touch

screen requires activation by a Chrysler/Dodge

dealer. See below for Dealer Programming

Instructions. If possible, have the dealer “enable”

the camera option prior to installation.

31. Use a Plastic Trim Tool to remove shifter bezel and

remove two screws from under the rubber mat using

a Phillips screwdriver.

32. Use a Plastic Trim Tool to remove cup holder bezel.

33. Remove rubber mat on top of 8.4” screen to expose

two screws and remove them using a T20 Torx bit.

34. Remove rubber mat in square cubby hole to expose

one screw and remove it using a T20 Torx bit.

35. Use a Plastic Trim tool to remove radio bezel to

expose the 4 screws securing the radio head unit

and remove them using a 7mm socket.

36. Unplug all radio connectors from the radio head unit

and set radio aside.

Note: If vehicle is NOT equipped with a 22-pin

radio connector (Figure 3), use supplied white

connector to complete steps 43 and 44.

Figure 3

IMPORTANT: If the white 22-pin connector is

present in the vehicle and pin 3 and/or pin 4 are

already populated, remove the terminal(s) using

Delphi terminal removal tool# 12094429 or a small

flat watch repair screwdriver and isolate with

electrical tape.

37. Locate pin position 3 on the white 22-pin radio

connector (Figure 3) and insert red terminal of the

jumper harness until it clicks securely.

38. Insert black terminal of the jumper harness into pin

position on the white 22-pin radio connector (Figure

3) until it clicks securely.

39. Connect white 22-pin connector to radio along with

all remaining connectors before reinstalling radio

head unite and all trim removed.

40. Route Chassis Harness behind rear cab mount and

out to the inside of the vehicle. RECOMMENDED:

Use a Wire Tie to secure Chassis Harness between

the cab and bed mount.

Remove bolt

to attach

eyelet on

Black Ground

wire from

supplied

Chassis

Harness to

Chassis

Ground bolt.

Remove ½”

bolt attaching

Instrument

Panel

connector

mount to gain

access to BCM

pink/green

Ignition

(12v+) wire.

Pin 4 – Black terminal Pin 3 – Red terminal

41. Continue to route supplied Chassis Harness next to

the existing wiring harness along the inside edge of

the frame rail. RECOMMENDED: Secure supplied

Chassis Harness to the existing wiring harness with

Wire Ties.

42. Once the Chassis Harness has been routed to the

rear of the truck bed, coil and secure any excess

length on the harness and tuck above the spare tire.

Secure with Wire Ties (recommended) or Electrical

Tape.

43. Plug Camera Harness connector into the Chassis

Harness connector at the rear of the vehicle.

44. Reconnect negative battery terminal

45. Start vehicle and shift into Reverse in order to check

that all connections were made properly. If all of the

connections are correct you will see the camera

image displayed on your aftermarket mirror /

display/ NAV display.

46. Reassemble all previously removed parts.

47. If you connected the camera to a factory 8.4”

touch screen, and the vehicle has not been

reprogrammed to “enable” the camera, have a

Chrysler/Dodge dealer program the vehicle as

follows:

Dealer Programming Instructions

PARK VIEW REAR BACK-UP CAMERA

VEHICLE CONFIGURATION

Vehicle VIN must be updated with the sales code of the

added accessory in order to enable system functionality.

Using the DealerCONNECT website and the scan tool,

complete the procedure below:

A. Log on to ourwebsite

B. In the “Vehicle Option” screen under “Global Claims

System” category in the “Service” tab, enter the

VIN and add the following sales code: XAC (PARK

VIEW REAR BACK-UP CAMERA) as a “Dealer

Installed Option.”

C. Confirm that the new sales code has been

successfully added to the VIN. With the scan tool

connected to both the internet (via Ethernet port or

wireless connection) and the vehicle, follow the

steps below:

D. Using the scan tool select the VEHICLE

PREPARATION and then select RESTORE VEHICLE

CONFIGURATION.

E. Follow the step by step instructions on the scan

tool to complete the Park View Rear Back-Up

Camera vehicle configuration.

48. Reconnect negative battery terminal

49. Start vehicle and shift into Reverse in order to check

that all connections were made properly. If all of the

connections are correct you will see the camera

image displayed on your factory screen.

50. Secure supplied Chassis Harness along the existing

Chassis Harness using Wire Ties (recommended)

every 200mm (approximately 8”). Note: Depending

on vehicle wheelbase there may be excess length in

the Chassis Harness. Loop, and secure with Wire

Ties (recommended) or Electrical Tape, any excess

harness length along the Body Frame away from

Mechanical areas.

51. Reassemble all previously removed parts

CAMERA!PARKLINE!OPTION

The camera offers Park lines or non-Park

lines options.

Park line options: Default setting displays

Park lines. To remove the grid line display,

pull back plastic convolute from end of camera

harness and connect the two green wires.

Display options: Do not use white wires.

Green and White wires on the Camera Harness.

Manuales populares de Cámara de visión trasera de otras marcas

iBeam

iBeam TE-3BCE Manual de usuario