Flavel Castelle Instrucciones de montaje

Castelle

INSET FUEL EFFECT GAS FIRE

Installation, aintenance & User Instructions

Hand these instructions to the user following installation

odel No’s FPCL**RN is only for use on Natural Gas (G20) at a

supply pressure of 20 mbar in G.B. / I.E.

** denotes colour variant

CONTENTS

Section 1 Information and Requirements PAGE

1.0 Appliance Information 3

1.1 Conditions of Installation 4

1.2 Flue and chimney suitability 4

1.3 Fireplace / surround suitability 4

1.4 Shelf position 5

1.5 Chimney inspection 5

1.6 Fire place opening / catchment space 6

1.7 Fitting to chair bricks 8

1.8 Precast flues 8

1.9 Metal flue boxes 8

1.10 Wall / hearth mounting 9

1.11 Spillage monitoring system 10

Section 2 Installation of Fire

2.1 Unpacking the fire 11

2.2 Installing the firebox 11

2.3 Preparation of firebox opening 12-17

2.4 Gas tightness and burner pressure 17

Section 3 Assembling Fuel Bed and Commissioning

3.1 Assembling the ceramics and fuel bed 18-22

3.2 Fitting the fascia 23

3.3 Lighting the appliance 24-25

3.4 Checking for clearance of combustion 33

products

3.5 Removal & re-fitting the draught diverter cover 27

3.6 Removal & re-fitting the flue restrictor baffle 28

Section 4 aintenance

4.1 Removal of the burner assembly 29

4.2 Removal of the gas valve 29-30

4.3 Removal of the pilot assembly 30

4.4 Removal of the batteries in the receiver 30

Parts shortist 31

Section 5 User Instructions

5.1 Conditions of Installation / about your new fire 32-33

5.2 Operating the fire 34-35

5.3 Spillage monitoring system 35

5.4 Re-assembling the fuel-bed 36-40

5.5 Removal & re-fitting the glass fascia 41

5.6 Removal & re-fitting the draught diverter cover 42

5.7 Cleaning the fuel-bed / glass fascia assembly 43

User replaceable parts 44

This appliance is manufactured by :-

BFM Europe Ltd,

Trentham Lakes, Stoke-on-Trent, ST4 4TJ

SECTION 1

INFOR ATION AND REQUIRE ENTS

1.0 APPLIANCE INFOR ATION

Model FPCL**RN

Gas Type G20

Main injector (1 off) Size 1.65mm

Pilot Type S.I.T. Oxystop YA OP 9061

Max. Gross Heat Input : 5.0kW

Min. Gross Heat Input : 2.8kW

Cold Pressure : 20.0 +/-1.0 mbar

Ignition : 6V Battery Generator

Electrode Spark Gap 4.0mm

Weight 29.5kg

Firebox dimensions

Width : (with fascia fitted) 750mm

Height : (with fascia fitted) 600mm

Depth : (overall-with fascia) 223mm

Depth : (from mounting face) 75mm

Gas Connection 8mm Compression (Supplied with fire)

Efficiency Declaration

The efficiency of this appliance has been measured as specified in

BS 7977-1 : 2009 and the result is 71.2%.

The gross calorific value of the fuel has been used for this efficiency

calculation.

The test data from which it has been calculated has been certified by BSI.

The efficiency value may be used in the U Government’s Standard Assessment

Procedure (SAP) for energy rating of dwellings.

INSTALLATION REQUIRE ENTS

1.1 CONDITIONS OF INSTALLATION

It is the law that all gas appliances are installed only by a GAS SAFE registered

Installer, in accordance with these installation instructions and the Gas Safety

(Installation and Use) Regulations 1998 as amended. Failure to install appliances

correctly could lead to prosecution. It is in your own interest and that of safety to

comply with the law.

The installation must also be in accordance with all relevant parts of the Local and

National Building Regulations where appropriate, the Building Regulations

(Scotland Consolidation) issued by the Scottish Development Department, and all

applicable requirements of the following British Standard Code of Practice.

1. BS 5871 Part 2 Installation of Inset Live Fuel Effect Gas Fires

2. BS 6891 Installation of Gas Pipework

3. BS 5440 Parts 1 & 2 Installation of Flues and Ventilation

4. BS 1251 Open fire place components

5. BS 715 / BS EN 1856-2 Metal flue pipes for gas appliances

6. BS EN 1858 Clay Flue Blocks and Terminals

7. IS 813 : 1996 Domestic Gas Installation (Republic of Ireland)

No purpose made additional ventilation is normally required for this

appliance, when installed in G.B. When Installing in I.E. please consult

document I.S. 813 : 1996 Domestic Gas Installation, which is issued by the

National Standards Authority of Ireland. If installing in Northern Ireland,

please consult local building regulations. Any purpose made ventilation

must be checked periodically to ensure that it is free from obstruction.

1.2 FLUE AND CHI NEY SUITABILITY

This appliance is designed for use with conventional brick built or lined chimneys

and fabricated flues and metal flue boxes conforming to BS 715 / BS EN 1856-2.

All flues must conform to the following minimum dimensions.

inimum diameter of circular flues 125 mm (Without Flue

Restrictor Fitted)

inimum effective height of all flue types 3 metres

When fitting to conventional chimneys or 175mm flues it may be desirable to

fit the flue restrictor baffle (supplied) to reduce the flue flow and increase the

efficiency of the fire. Safe clearance of products must always be checked by

carrying out a smoke match test as described.

1.3 FIREPLACE / SURROUND SUITABILITY

The fire must not be installed directly onto carpet or other combustible floor

materials. See page 9 for further details regarding hearth panels.

The fire is suitable for fitting to non-combustible fire place surrounds and

proprietary fire place surrounds with a temperature rating of at least 150oc.

If a heating appliance is fitted directly against a wall without the use of a fire

surround or fire place all combustible material must be removed from behind

the trim. Soft wall coverings such as blown vinyl, wall paper etc. could be

affected by the rising hot air and scorching and/or discoloration may result.

Due consideration should be made to this when installing or decorating.

1.4 SHELF POSITION

The fire may be fitted below a combustible shelf providing there is a minimum

distance of 200mm above the top of the fire and the shelf does not project more

than 150mm. If the shelf overhangs more than 150mm the distance between the

fire and the shelf must be increased by 15mm for every 25mm of additional over-

hang over 150mm.

1.5 FLUE / CHI NEY INSPECTION

Before commencing installation, a flue or chimney should be inspected to ensure

that all the following conditions are satisfied.

1. Check that the chimney / flue only serves one fire place and is clear of any

obstruction. Any dampers or register plates must be removed or locked in

the open position.

2. Brick/stone built chimneys or any chimney or flue which has been used for

an appliance burning fuel other than gas must be thoroughly swept. The

base of the chimney / flue must also be thoroughly cleared of debris etc.

3. Any under-floor air supply to the fire place must be completely sealed off.

4. Ensure that the inside of the chimney / flue is in good condition along it’s

length and check that there is no leakage of smoke through the structure

of the chimney during and after the smoke pellet test. With pre-cast flues

it is especially important to check the inside of the flue for extruded

cement / sealant protruding from the joints between the flue

blocks. If present, these should be removed by rodding the flue

before proceeding with the installation.

5. Using a smoke pellet, check that there is an up-draught in the chim

ney / flue and that the smoke can be seen issuing from the terminal /

chimney pot outside.

There must be no leakage of smoke through the structure of

the chimney during or after the smoke pellet test and it is

important to check inside upstairs rooms adjacent to the chimney /

flue. Check the chimney pot / terminal and general condition of the

brickwork or masonry. If the chimney or flue is in poor condition or if

there is no up-draught do not proceed with the installation. If there is a

history of down-draught conditions with the chimney / flue, a tested and

certificated flue terminal or cowl suitable for the relevant flue type should

be considered.

6. A spillage test must always be carried out during commissioning of

the appliance.

1.6 FIRE PLACE OPENING AND CHI NEY CATCH ENT SPACE

The front opening of the fire place must be between 350mm and 400mm wide,

and between 490 and 500mm high. If the opening exceeds these dimensions then

a surround must be constructed from suitable non-combustible material to produce

a correct size opening. Any surround must be suitably sealed to the fire place to

prevent leakage. See below in figure 1.

When installing into a brick built chimney, you must ensure that there is sufficient

depth to accomodate any debris which may fall from the chimney. This depth

must be sufficient to accomodate 12 litres of volumetric space.

Fire Opening

350mm Minimum

400mm Maximum

520mm

Minimum

420mm Minimum

Fig. 1

490mm Minimum

500mm Maximum

NOTE : Mini u

25 clearance

for fascia also

required below

botto edge of

opening

Minimum Flat

Sealing Area

Table A - Installation Depth Requi ements fo a Flavel Castelle being

installed into a b ick built chimney, equi ing 12.0 lit es of deb is collection

volume (figu e 2).

The chimney requires a minimum of 50mm clearance when measured from the

mouting face of the fire behind the firebox to accomodate 12.0 litres of debris

collection.

See figure 2 below for explanatory diagram.

Fig. 2

1.7 FITTING TO FIREPLACES WITH EXISTING CHAIRBRICKS AND

CONVENTIONAL BRICKBUILT CHI NEYS

This appliance is suitable for use in fireplaces fitted with an existing chairbrick

without the need for removal of the chairbrick, providing the minimum depth of the

fireplace from mounting face to chairbrick exceeds 125mm. The fireplace must be

checked to ensure that no part of the chairbrick is within 50mm of the flue outlet of

the fire when installed.

Opening Width ( e.g. 400mm)

Depth Required

(e.g. 125mm)

1.8 FITTING TO PRE-CAST FLUE INSTALLATIONS

To install the fire box in to pre-cast flue starter blocks, there must be at least

100mm from the mounting face of the fire to the rear of the pre-cast flue

starter block to allow sufficient space for debris collection. It is important to

consider this depth if choosing a fire surround as the thickness of the fire surround

must be sufficient to give a total depth of at least 100mm to the rear of the

starter block, otherwise there will be insufficient depth. To increase this depth the

fire surround may be packed away from the wall using suitable non-combustible

board, providing the installation is correctly sealed. If in doubt about the suitability

of the fire contact BFM Europe Ltd. for advice before proceeding.

It is important to ensure that the pre-cast flue is in good condition and is free from

extruded mortar or sealant from between the flue blocks.

This appliance has been tested for use in a pre-cast flue block complying

with BS EN 1858. In accordance with BS EN 1858, pre-cast flues built with

directly plastered faces (front or rear) are not correctly installed as to ensure

proper operation with any type of gas fire. In some instances of this flue

construction, temperature cracking of surface plaster may occur through no

fault of the appliance. An air gap or some form of insulation material should

be installed to prevent normal flue temperatures from damaging wall

surfaces.

1.9 FITTING TO PRE-FABRICATED TWIN WALL ETAL FLUE BOXES

The appliance may be fitted to twin wall metal flue boxes conforming to the

constructional requirements of BS 715, (for example the Selkirk LFE 125 box).

The box must have a minimum flue diameter of 125mm internal and minimum

internal dimensions of 160mm deep by 490mm high by 350mm wide. There are

no maximum dimensional requirements for the box. The top face of the box must

be insulated with a minimum thickness of 50mm of non-combustible mineral wool

insulation or similar material. The flue box must stand on a non-combustible base

of minimum thickness 12mm.

1.10 WALL / HEARTH OUNTING

This appliance must be fitted on a flat, non-combustible base of minimum

thickness 12mm. In addition, a non-combustible hearth or physical barrier should

be provided in front of the fire.

With “hole in the wall” type installations, where it may be desirable not to fit a

hearth panel or physical barrier, the product may be installed in accordance with

Document J of the building regulations so that every part of theflame or

incandescent material is at least 225mm above the floor level. For the customers

safety, and in accordance with BS 5871-2, the fitting of a hearth panel or physical

barrier should be carried out. Should this advice not be followed however, please

give consideration to the safety of the occupants in the room to which the

appliance is installed.

Any hearth panel or physical barrier that is fitted should project a mnimum of

300mm forwards from the fire opening and 150mm either side of the fire

opening, as shown below in figure 3. Any physical barrier must be securely fixed

and be of robust design.

Fig. 3

Example of Wall

Mounted hysical /

Tactile Barrier

Example of Floor Mounted

hysical Barrier i.e. Hearth

anel

Fireplace Opening

300mm

Minimum

300mm

Minimum

150mm Minimum each

side of fireplace

opening

1.11 SPILLAGE ONITORING SYSTE

This appliance is fitted with an atmosphere sensing spillage monitoring system in

the form of an oxygen sensing pilot. This is designed to shut the fire off in the

event of a partial or complete blockage of the flue causing a build up of

combustion products in the room in which the fire is operated. The following are

important warnings relating to this spillage monitoring system :-

1.11.1 The spillage monitoring system must not be adjusted by the installer.

1.11.2 The spillage monitoring system must not be put out of operation.

1.11.3 When the spillage monitoring system is exchanged only a complete

original manufacturers part may be fitted. It is not possible to replace

individual parts on the pilot system on this appliance, only a complete

pilot assembly (including the thermocouple) may be fitted.

Tabla de contenidos

Otros manuales de Chimenea de interior de Flavel

Flavel

Flavel "Waverley" Inset Tray FITC00MN Instrucciones de montaje

Flavel

Flavel Pure FPRG**RN2 Manual de usuario

Flavel

Flavel ATLANTA FBFR**MN Manual de usuario

Flavel

Flavel Calibre FBFC**MN2 Instrucciones de montaje

Flavel

Flavel Calypso FNCN**SN Series Manual de usuario

Flavel

Flavel FOPC MN Series Instrucciones de montaje

Flavel

Flavel FWERN0MN Manual de usuario

Flavel

Flavel Decadence HE Instrucciones de montaje

Flavel

Flavel Renoir FRECR0MN Manual de usuario

Flavel

Flavel Renoir FRECN0EN Instrucciones de montaje

Flavel

Flavel Expression HE Instrucciones de montaje

Flavel

Flavel Finesse FSRC**MN Instrucciones de montaje

Flavel

Flavel Richmond Plus Manual de usuario

Flavel

Flavel Caress Manual de usuario

Flavel

Flavel FRDC**MN Series Manual de usuario

Flavel

Flavel Warwick FIRC**MN Manual de usuario

Flavel

Flavel Curve FCRR Series Manual de usuario

Flavel

Flavel Linear Instrucciones de montaje

Flavel

Flavel Quasar NRDC MN2 Series Instrucciones de montaje

Flavel

Flavel Vesta Instrucciones de montaje

Flavel

Flavel Misermatic FRCM1G Manual de usuario

Flavel

Flavel Onyx MK2 FFHOW0RE2 Manual de usuario

Flavel

Flavel Emberglow Classic FEMC00MN Manual de usuario

Flavel

Flavel Caress Slimeline SC FNVC**SN Manual de usuario

Manuales populares de Chimenea de interior de otras marcas

Brigantia

Brigantia 35-DVRS31N-2 Manual del propietario

Nordpeis

Nordpeis Bergen Manual de usuario

Superior

Superior BCT2536TMN Manual de usuario

Quadra-Fire

Quadra-Fire 5100I-GD-B Manual de usuario

Renaissance

Renaissance RUMFORD 1000 Manual de usuario

Lacunza

Lacunza IV-800 Manual de usuario

Baxi

Baxi 940 Instrucciones de uso

Dru

Dru Maestro 60/2 Tall RCH Manual de usuario

Diamond Fireglass

Diamond Fireglass SS-O22 Manual de usuario

HearthStone

HearthStone Windsor Bay 8830 Manual de programación

Napoleon

Napoleon ASCENT B42 Manual de usuario

Enviro

Enviro E33GI Manual de usuario

Smeg

Smeg L30 FABE Instrucciones de montaje

KEDDY

KEDDY K700 Manual de usuario

Godin

Godin 3451 Manual de usuario

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manual de usuario

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manual de usuario

Desa

Desa CCFPDFT Manual de operación