FLATLIFT EXTRA FLAT Manual de usuario
P.01
Operating Manual
Outperform. Outlast.
Well thought-out space-saving!
Operating Manuel
Operating Manual
P.02
Operating Manual
Outperform. Outlast.
CONTENTS
CONTENTS
C.01 INTRODUCTION
C.02 FEATURES
C.03 PRODUCT DIMENSIONS
C.04 INITIAL PRODUCT SET UP
Set-up P.06
Images P.07
C.05 PRODUCT CONTROL
C.08 TROUBLE SHOOTING
Programming the remote control (S435) P.08
Resetting the receiver P.09
Connecting to a room control system P.09
C.09 LEGAL NOTICE
C.06 PRODUCT INTEGRATION
C.07 RECOMMANDED INSTALLION
Example of console integration P.13
Example of back of sofa integration P.14
P.03
Operating Manual
Outperform. Outlast.
CONTENTS
INTRODUCTION
INTRODUCTION
C.01:
Intended Use
The product serves the lifting and lowering of LCD and plasma TV equipment.
All company names and product names are trademarks of the corresponding owner. All rights reserved.
The scope of supply can vary depending on the product and the range of xtures and ttings. Please
check that the product supplied is complete and inform us within seven days of delivery if the scope of
supply is not complete.
Safety and Hazards Recommendations
Please read this chapter carefully and follow all of the instructions provided. In this way you are able to
guarantee the reliable operation and a long lifespan for your lift system. Keep the operating manual in a
safe place.
In the event of damage which is the result of non compliance with this operating manual, all claims pertai-
ning to the guarantee are null and void. We generally accept no responsibility for secondary damage.
We accept no responsibility for damage to objects or persons which is caused by the inappropriate use of
the product or through ignoring the safety instructions. In such cases, all claims pertaining to the guaran-
tee are null and void.
Quality
In the choice of our components, our primary focus was on ensuring a high level of functionality,
straightforward use, safety and reliability.
We would like to thank you for the trust you have placed in our Flatlift brand products.
We can help you with your installation through providing individual customer care.
For safety reasons, the unauthorized conversion and/or changing of the product is not permitted. Do not
dismantle this product.
This product is not a toy and does not belong in the hands of children.
Do not allow the product to become damp or wet.
Do not leave the packaging material lying around as children may choke if they swallow it.
The product will be damaged if it is dropped, even from a low height.
Before using the product for the rst time, please check that the free raising and lowering of the Flatlift
including the mounted TV equipment is possible and ensure a collision-free run.
For legal reasons and insurance purposes, your Flatlift is equipped with an ‘automatic safety
device’.
This means that the button which controls the raising and lowering must be pressed down all
the time.
The system stops and remains in the same position as soon as you let go of the button.
P.04
Operating Manual
Outperform. Outlast.
PRODUCT FEATURES
PRODUCT FEATURES
C.02:
Features:
Installation base
W=400 mm D=215 mm
Installation dimensions, Flatlift
W=785mm D=85mm H=800mm
Lift 965mm
Lifting speed 45 mm / sec
TV weight max. 45 kg / 450N / including cover (P.012)
TV size 43-50“ (inches)
(max. TV size possible in mm: W = * , H = max. 916, D = *)
Power-on time 18%/h
Can be tilted (-15° manual).
Soft Start / Soft Stop
Low noise level < 45 dB
Environmental temperature from +5°C to 40°C
Connection to room control system possible (refer to P.09 image 5)
Automatic TV switch-off (optional)
Millimetre-exact programming of the stopping point (optional)
230V emergency power supply (optional)
Flatlift Extraat 43“ / 50“
Control box
230V power cord
Motor cable
12V wall power supply for the receiver
433.92 MHz 2 channel receiver
433.92 MHz 2 channel transmitter
Scope of supply:
L
I
F
E
T
I
M
E
R
e
p
a
i
r
c
o
s
t
l
i
m
i
t
5
y
e
a
r
s
f
u
l
l
s
e
r
v
i
c
e
GUARANTY
P.06
Operating Manual
Outperform. Outlast.
INITIAL PRODUCT SET U
INITIAL PRODUCT SET UP
C.04:
Initial set up:
1. In order to prevent the system from tipping over, x your Pop-Up installation base to the oor using 4
screws (image 1 no. 1).
2. Connect the Flatlift (image 1, no. 3) with the motor cables (P.07, image 3) and connect these with the
control box (image 2, no. 5) at connection point ‘1’. The motor cables must be connected starting
at port 1 and going up.
3. Connect the RJ-45 Western plug of the receiver (P.07, image 4, no. 7) to the control box (image 2, no. 6).
4. Connect the control box (image 2, no. 4) with the power cord (P.07, image 5) to the mains supply.
5. Connect the wall power supply of the receiver (image 2, no. 4) with the power cord (P.07, image 5) to the
mains supply.
6. Now initialise the Flatlift by pressing down the ‘Down’ key on the controller (P.07 image 6 no. 9) for 2 x 5
sec. After this, extend and retract your Flatlift fully twice over.
7. Your Flatlift is now ready for use as the end points of the lift have now been saved in the control box.
8. You are now able to mount your TV set on the system. To do this, uncouple the two holders (image 1 no.
2). Attach these to your TV and then secure the holder subsequent to putting the TV set in place by
screwing in the safety screw (image 1, no. 4).
If you separate the motor cable from the control box, then the Flatlift must be initialised all
over again.
Image 1
2
1
1
3
456
Image 2
5
4
P.08
Operating Manual
Outperform. Outlast.
Programming the remote control (S435):
You can also get additional remote controllers for your Flatlift system (optional extra). As the controllers are
coded, you have to programme them.
1) To access the programming key, remove the cover (image 1, no. 1) on the receiver.
2) Press down the left hand key (image 1, no. 2). After this, an LED (image 1, no. 3) will then ash slowly.
3) Holding the programming key down, press the rst key on the remote control at the same time (image
2, no. 5). On recognising the remote control, the LED (image 1 no. 3) starts to ash rapidly.
4) Release both of the keys.
5) To store a second channel, repeat the procedure starting at step 2 using the second key on the remote
control (image 2, no. 6). If your remote control has been successfully recorded, you should hear a soft
‘click’ in the receiver when you press down the key on the controller.
Image 2
56
3
4
1
Image 1
PRODUCT CONTROL
PRODUCT CONTROL
C.05:
2
P.09
Operating Manual
Outperform. Outlast.
PRODUCT CONTROL
Resetting the receiver:
It may sometimes occur that the transmitting codes stored in the receiver are lost.
In this case, the receiver must be cleared and re-programmed.
1) To access the programming key, remove the cover (image 1, no. 1) on the receiver.
2) Press down both of the programming keys (image 3, no. 2 + 4) until the LED (image 3, no. 3) rapidly
ashes. This is the signal that the memory has been successfully cleared.
3) Now re-enter your remote control (refer to P.08).
Connection to a room control system:
You can connect your Flatlift to a room contro
l system (image 5) if this system has 2 relay outputs
with potential free contacts. These relays must be
actuated for a programmable time period.
1) Remove the receiver from the power supply
2) Remove the cables (contacts 2-4) from the receiver
(image 4).
3) Now connect the blue and red cable to one of the
relay outputs (control command: lower Flatlift).
4) Bridge the blue cable onto the second relay
output and also attach the green cable to this
relay output (lift Flatlift).
Image 3
2
3
4
1
Image 5
PRODUCT CONTROL
PRODUCT CONTROL
C.05:
Image 4
P.010
Operating Manual
Outperform. Outlast.
C.06:
PRODUCT INTEGRATION
PRODUCT INTEGRATION
Image 1
Lid variation 1:
A lid closing mechanism on the
rear section of the unit incor-
porating spring damped hinges
which opens automatically when
the Flatlift moves upwards.
Different lid closing solutions are
available depending on the reali-
sation of the project (image 1).
The A/V installer which is ins-
talling the Flatlift thus enjoys
exibility and can also change
the lid solution again at a later
time. When the Flatlift retracts,
the cover closes softly thanks to
the spring dampened hinges.
Tabla de contenidos
Otros manuales de Soporte de TV de FLATLIFT
