Flashforge PACFG00069 Manual de usuario
This guide is only applicable to FLASHFORGE Filament Drying Station
本手册仅适用于闪铸科技 材料烘干箱
中文P16
用户使用手册
USER GUIDE
EN/CN-A01 Filament Drying Station 材料烘干箱
Content
NOTICE
1. Introduction
1.1 - Product Introduction
1.2 - Packing List
1.3 - Equipment Parameter
1.4 - Combined Use
2. Equipment Operation Introduction
2.1 - Storage Function
2.2 - Drying Function
2.3 - Annealing Treatment
2.4 - Filament Drying Station Setting
3. Replace the Desiccant
4. Q&A
5. Support and Service
01
03
03
03
04
05
06
06
07
09
10
12
13
15
Please keep the work table of the equipment clean and tidy.
Please keep the equipment away from combustible gases, liquids and dust when
working. The high temperature generated during the equipment operation may react
with flammable liquids, gases, and airborne dust, thus causing fire.
Children and untrained personnel are not allowed to operate the equipment alone.
WORK ENVIRONMENT SAFETY
PLEASE STRICTLY FOLLOW ALL THE SAFETY WARNINGS AND NOTICES BELOW ALL THE TIME.
Be sure to ground the equipment. Do not modify the plug of the equipment.
Ungrounded equipment/improperly grounded equipment/modified plug will
inevitably increase the risk of electric leakage.
Do not expose the equipment to damp or hot-sun environment. Humidity will
increase the risk of electric leakage. Exposure to sunlight will accelerate the aging of
plastic parts.
Make sure to only use the power cord provided by Flashforge.
Do not use the equipment during a thunderstorm.
Please shut down the equipment and unplug it if it is not in use for a long time.
ELECTRICAL SAFETY
Do not touch the high-temperature position directly when the equipment is in
operation!
Do not operate the equipment while you are tired or under the influence of drugs,
alcohol or medication!
PERSONAL SAFETY
The room temperature should be between 15℃ and 30℃.
The humidity should be between 20% and 70%.
ENVIRONMENT REQUIREMENTS
NOTICE
The equipment must be placed in a dry and ventilated environment. At least a
10cm-distance must be reserved on the left side, right side and rear side of the
equipment.
EQUIPMENT PLACEMENT REQUIREMENTS
01
The user has no right to make any modification to this user guide.
Flashforge will not be responsible for any safety accidents caused by the disassembly
or modification of the equipment by the customer. No one is allowed to modify or
translate this guide without the permission of Flashforge.
This guide is protected by copyright, and Flashforge reserves the right of the final
interpretation of this guide.
Flashforge reserves the right to modify the guide due to subsequent equipment
upgrades.
First Edition (March 2022)
Copyright © 2022 Zhejiang Flashforge 3D Technology Co., Ltd. All Rights Reserved.
LEGAL STATEMENT
02
1. Introduction
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Storage Drawer
Drawer Pull
Temperature Probe
Drawer Sealing Strip
Stop Block
Display Screen
Caster
Protective Cover
Drawer Slide
Rear Cover Plate
Power Switch
Power Outlet
Back Plate
Air Inlet
Air Outlet
1
2
3
4
5
6
7
8
9
1.1 Product Introduction
1.2 Packing List
03
Allen Wrench Stop Block*2
Power Cord
Screw*4
Filament
Drying Station
Heat Insulating
Gloves
10
11
12
14 13
15
Size
Screen
Language
Maximum drying temperature
Desiccant service time
Desiccant capacity
Storage humidity control range
Internal storage size
Power
Bearing weight
Package size
Package weight
Power during storing
Power during drying
(12hrs, 120℃)
Power consumption
(drying for 12hrs at 120℃)
Applicable material
840x*675y*600z mm (with casters)
4.3-inch touch screen
Chinese/English/Japanese/German/French/Korean
120℃
1 year
800g
10-20%
500*375*200 mm(WxDxH)
500W
120kg
980*780*830 mm
100kg
Average: 30W; Maximum: 35W
Average: 100W; Maximum: 500W
About 1.4KWh
Moisture-sensitive materials:
PVA / PVOH / BVOH / PVB / PA6 / PA12 / PA66 /
PC / ABS / ABS Pro / HIPS / ASA / PET / PETG /
WOOD / Metal Fill
Moisture-sensitive fiber reinforced materials:
PA6-CF / PA12-CF / PA66-CF / PET-CF / PP-CF /
ASA-CF / PETG-CF / PLA-CF / PPS-CF / PA6-GF /
PLA-GF
1.3 Equipment Parameter
04
This filament drying station can be used together with Creator 4 series equipment, which
can be placed above the filament drying station.
After finishing placing, tighten the installation fixing block with screws.
1.4 Combined Use
05
06
2. Equipment Operation Introduction
Connect the power supply, turn on the power switch, and start the machine;
If the filament has absorbed moisture, it is necessary to enable the drying function to dry
the filament;
If the filament has not absorbed moisture, only the storage function needs to be enabled
to store the filament.
The default storage range of the equipment is less than 15%; After starting up the
equipment, the storage function is enabled by default;
The interface will display the current temperature and humidity of the filament chamber.
The humidity value will change as the storage function is turned on until the humidity
reaches the set humidity storage range.
It adopts the renewable desiccant, which can be recycled, for storage; When the auto
cycle function is enabled and the equipment detects that the desiccant is moisture-satu-
rated, the humidity of the chamber will become higher, and at this time, the desiccant
dehumidification function will be enabled automatically, so that the desiccant can be
dried again. At this time, it is normal that the humidity display value may fluctuate.
There will be corresponding prompts in the interface.
2.1 Storage Function
Note Please be sure to keep the door closed during storage.
Click on the drying function bar and select the filament to be dried. The default drying
time and temperature has been set already when leaving the factory.
The interface will display the target drying temperature and actual temperature, total
drying time and remaining time and chamber humidity value.
2.2 Drying Function
Note
Users can also customize the material and set the required drying time and temperature
for it.
·
·
·
·
Please be sure to keep the door closed during drying;
If the hot melt characteristics of the materials differ greatly, they can not be dried at the same
time. For example, PLA material, of which the softening temperature is 53℃, is not suitable for
drying together with high-temperature resistant materials such as PC and PA.
The filament spool material is usually ABS/PC-ABS/PC material. If the temperature is too high,
the filament spool may be deformed. For filaments shipped after May 2022, Flashforge will
adopt PC-ABS material for the spool.
Note that if the temperature displayed by the filament drying station exceeds 50℃ when taking
the filament out, please wear heat insulating gloves to avoid scalding.
07
The following softening temperatures of filaments are for reference only:
The heat deflection temperature varies under different experimental conditions.
08
PA12-CF15(9891BK)
PA6-CF10
PA66-CF10
PET-CF15(9780BK)
PETG-CF10
PLA-CF10
PC-ABS
PA6/66
PA1010
PAHT
PC
PP
HIPS
PLA PRO
PLA
PETG PRO
PETG
ABS PRO
PBT
90
200
150
100
70
60
123
85
100
90
105
113
98
53
53
68
74
103
127
Filament Heat Deflection Temperature(℃)
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Manuales populares de Secadora de otras marcas
Indesit
Indesit IDV 75 Manual de usuario
Infiniton
Infiniton SD-DG85C Manual de usuario
BOMANN
BOMANN WT 5019 Manual de usuario
Alliance Laundry Systems
Alliance Laundry Systems TMB795C Manual de usuario
Asko
Asko T793C Manual de usuario
Kenmore
Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Manual de usuario