FiveO WiP 160 Manual de usuario

W iP 160/160 C

Wireless microphone systems

Sistema UHF senza ﬁli

ENGLISHITALIANO

[EN] owNEr’s maNual

[IT]

Manuale d’uso

(pag. 2)

(pag. 10)

Owner’s manual | WiP 160/160C Wireless Microphone Systems WiP 160/160C Wireless Microphone Systems | Owner’s manual

W iP 160/160 C

WARNING

In order to protect your own and others’ safety and

to avoid invalidation of the warranty of this product,

please read this section carefully before operating

this product.

∙ Read all documentation before operating your equipment.

∙ Retain all documentation for further reference, supplying

it to any user.

∙ Read all warnings and follow all instructions contained in

this instruction manual.

∙ Damages caused by connecting to improper AC voltage

are not covered by any warranty. Mains voltage must

correspond to rear unit label.

∙ AlwaysoperatetheunitwiththeACgroundwireconnected

to theelectrical systemground.Precautions shouldbe taken

toavoidequipmentfaulty,improperorinefﬁcientgrounding.

∙ Clean the device only when not connected to the mains.

For cleaning, use a dry cloth.

∙ To reduce the risk of ﬁre or electric shock, do not use the

device near water and don’t expose it to rain.

∙ Useonlythesuppliedpoweradapter,disconnectingitduring

lightning storms or when unused for long periods of time.

∙ To prevent overheating, the devices must be placed away

from sources of heat (radiators, heat registers, stoves,

ampliﬁers or other equipment) nor be exposed to direct

sunlight.

∙ Referallservicingtoqualiﬁedandauthorizedpersonnelonly.

Servicing is required when the device has been damaged in

any way, whether in liquid has been spilled or objects have

fallen into, the devices were exposed to rain or moisture,

or the devices does not operate properly or have fallen.

CAUTION

This product does not contain user serviceable parts. In order

to prevent ﬁre and/or electrical shock, never disassemble it.

For maintenance and servicing always refer to the ofﬁcial

FiveO by Montarbo®Distributor in your Country or to qua-

liﬁed personnel speciﬁcally authorised by the Distributor.

WEEE | Waste from Electrical and Electronic Equipment

ATTENTION!

The crossed out wheeled bin symbol that can be found on this

product means that the product is covered by the Waste from

Electrical and Electronic Equipment Directive.

The symbol is intended to indicate that waste from

electrical and electronic equipment must be subject to a selective collec-

tion. For more details on available collection facilities please contact your

local government ofﬁce or the retailer where you purchased this product.

The solid bar underneath indicates that the product has been put on the

market after 13th August 2005.

INFORMATION ON PROPER DISPOSAL

Information on Disposal for Users (private households)

In the European Union | Attention: If you want to dispose of this

equipment, please do not use the ordinary dust bin! Used electrical and

electronic equipment should not be disposed of via the normal household

waste stream but must be treated separately and in accordance with le-

gislation that requires proper treatment, recovery and recycling of used

electrical and electronic equipment. Following the implementation by

member states, private households within the EU states may return their

used electrical and electronic equipment to designated collection facilities

free of charge*. In some countries* your local retailer may also take back

your old product free of charge if you purchase a similar new one. *Plea-

se contact your local authority for further details.

In other Countries outside the EU | If you wish to dispose of this pro-

duct, please contact your local authorities and ask for the correct method

of disposal.

In Switzerland | Used electrical or electronic equipment can be returned

free of charge to the dealer, even if you don’t purchase a new product.

Further collection facilities are listed on the homepage of www.swico.

ch or www.sens.ch.

Information on Disposal for Professional Users

In the European Union | If the product is used for business purposes

and you want to discard it: please contact your FiveO by Montarbo®de-

aler who will inform you about the take-back of the product. You might

be charged for the costs arising from take-back and recycling. Small pro-

ducts (and small amounts) might be taken back by your local collection

facilities.

In Spain | Please contact the established collection system or your local

authority for takeback of your used products.

In other Countries outside the EU | Please contact your local authori-

ties and ask for the correct method of disposal.

Important precautIons

Owner’s manual | WiP 160/160C Wireless Microphone Systems WiP 160/160C Wireless Microphone Systems | Owner’s manual

ENGLISH

contents

Introduction 4

Features 4

All systems include 4

Receiver 5

Handheld transmitter 6

Body-pack transmitter (WiP 160C only) 7

Tips 8

Troubleshooting 8

Speciﬁcations 9

pacKaGe contents

Receiver

Hand-held transmitter

Body-pack transmitter (WiP 160C only)

Headset microphone (WiP 160C only)

AA-size batteries

6.35 mm (¼”) Jack-Jack cable

Power adapter

ABS protection case

Owner’s manual

Warranty certiﬁcate

Owner’s manual | WiP 160/160C Wireless Microphone Systems WiP 160/160C Wireless Microphone Systems | Owner’s manual

W iP 160/160 C

INTRODUCTION

First of all, thank you for choosing a product FiveO by Montarbo®. This line has been designed for those who

want to set-up their user friendly audio sound system with excellent performances and outstanding value. Furthermore,

we manufactured all these products to assure you satisfying and reliable operation over many years. Our WiP 160 is

a professional UHF wireless microphone set including an hand-held as well as a belt-pack and a headset microphone.

This versatile single channel, antenna diversity receiver will provide you 16CH of wireless transmission. Please, in order

to enjoy each feature of your new microphone thus achieving the best sonic performances, take a few moments

to carefully read these instructions. For further information about your microphone, please check our website

www.ﬁveo.it, or send an email to: mail@ﬁveo.it

FEATURES

WiP 160 microphones sound character is perfectly tailored for female and male vocals. The choice among 16

transmitting and receiving channels will provide you performances without RFI. Being aware of the heavy use your

WiP 160 should run in most demanding live applications, we manufacture it in a sturdy way. Please, be careful

handling your WiP 160 microphones. Despite the ruggedness of our manufacture, the internal microphone

diaphragms are very thin and these diaphragms could suffer for mechanical shocks and for excessive moisture and

dust collecting. Finding the optimal microphone placement is basically a process requiring trials; so make your own

experience starting from mic tech specs and your knowledge, continuously using your musical sensibility and your ears.

To achieve best sonic results, we suggest you to use your WiP 160 hand-held mic very close to your mouth, you

should experience some proximity effect, boost of lower frequencies, but increasing the distance you risk feedback and

other instruments pick-up. The headset mic will be used very close to your mouth bending the mic boom, while the

lavalier microphone will be attached to speaker clothes. On stage use, please be careful to wedge monitor placement,

since you could incur in feedback with very high sound pressure level!

ALL SYSTEMS INCLUDE:

1 x Receiver

1 x Hand-held transmitter

1 x Body-pack transmitter (WiP 160C only)

1 x Headset microphone (WiP 160C only)

2 x “AA” size batteries

1 x 1/4” cable

1 x Power adapter

1 x ABS protection and transport case

Owner’s manual | WiP 160/160C Wireless Microphone Systems WiP 160/160C Wireless Microphone Systems | Owner’s manual

ENGLISH

RECEIVER

FRONT PANEL

1IR – Infrared port. It’s the emission point of IR

signal to match channel with the transmitter.

AF – Audio signal indicator.

RF – Radio Frequency indicator. It’s lit when

the receiver detects a transmitter on the selected

IR channel.

Display. It displays the channel number.

Volume control knob.

SELECT – Channel selector.

Read «System Setup» below.

ASC – Automatic Search of Channel button.

Press it to initiate matching between receiver and

transmitter.

AC adapter jack.

Unbalanced output Jack (6.35mm - ¼”)

[!] Attention: in order to rationalize the costs

the written “2 IN 1 MIX” is used for the whole

wireless systems range. However, when using the

single channel models (WiP 160/160 C) the main

out works indeed as a single output.

1 2 3 4 5

6 7

8 9

REAR PANEL

System Setup

Receiver Programming

By pressing the ASC button, the receiver will transmit IR signal to transmitter for automatic frequencies

matching.During IR signal transmission, the display will ﬂash. The display character will be ﬁrmly lit when

receiver and transmitter frequencies will be locked.

Press the SELECT button to select operating channel, when the receiver will detect a working transmitter, the RF LED

will remain lit and the AF LED will be lit receiving signal from transmitter. Turn the receiver volume control clockwise

to raise the output volume, or counter-clockwise to decrease the output volume.

Note: Using multiple systems, it’s better to set the maximum channel spacing among units.

You can use up to 8 WiP systems simultaneously.

Owner’s manual | WiP 160/160C Wireless Microphone Systems WiP 160/160C Wireless Microphone Systems | Owner’s manual

W iP 160/160 C

HANDHELD TRANSMITTER

1Microphone capsule.

Power/Low battery indicator.

Green: Ready

Red: Low battery.

ON/OFF switch.

Battery cover.

IR port. Receives infrared beam to match

receiver and transmitter channel.

2 3

4 5

Handheld Transmitter Setup

Match the channel between transmitter and receiver

by aligning the infrared(IR) ports and pressing the

ASC button.

Note: Make sure the infrared (IR) ports of the

receiver and transmitter are closely aligned. When

using multiply systems, only one transmitter IR

port should be matched at a time.

Replacing Batteries

Expectedlifefortwoalkalinebatteriesisabout10

hours. As thebattery indicator on the screen keeps

glowing , the batteries should be immediately

changed (as shown below).

open close

Owner’s manual | WiP 160/160C Wireless Microphone Systems WiP 160/160C Wireless Microphone Systems | Owner’s manual

ENGLISH

BODYPACK TRANSMITTER (WiP 160C only)

Replacing batteries

Expectedlifefortwoalkalinebatteries

is about 10 hours. As the battery

indicator on the screen begins

glowing, the batteries should be

immediately changed(as shown

above).

3 4 5

1Antenna.

Power/Low battery indicator.

Green: Ready

Red: Low battery.

Microphone Input Jack.

Gain adjustment selector.

Three settings are available.

Mic: microphone.

0: Guitar with passive pickups.

-10dB: Guitar with active pickups.

ON/STANDBY/OFF selector.

ON/OFF switch. When it’s in its

middle position, the transmitter

is muted

IR port. Receives infrared beam

generated by the receiver to

match channel.

Wearing the Belt-pack Transmitter:

Clip the transmitter to belt [A], or slide a guitar strap through the

transmitter clip [B], as shown in the left. For best results, slide the

transmitter until the belt 1 is ﬁrmly pressed against the base of the clip.

[A] [B]

open/close

Body-pack Transmitter Setup

Match the channel between transmitter and receiver by aligning the

infrared (IR) ports and pressing the ASC button. Note: Make sure

the infrared (IR) ports of the receiver and transmitter are closely

aligned. When using multiply systems, only one transmitter IR

port should be matched at once.

Owner’s manual | WiP 160/160C Wireless Microphone Systems WiP 160/160C Wireless Microphone Systems | Owner’s manual

W iP 160/160 C

TIPS

∙

Maintain a line of sight between transmitter and antenna.

∙

Avoid placing the receiver near metal surfaces or any digital equipment (CD players, computers, etc).

∙

Keep the receiver away from the wall and over 1m to the ground.

∙

Transmitting devices such as cellular phones and two-way radio may interfere with wireless audio transmission.

Keep the transmitter and receiver away from this and other potential sources of interferences.

TROUBLESHOOTING

Issue Indicator Status Solution

No sound or faint

sound

No Transmit

Turn on transmitter.

Make sure the +/- indicator on battery match the

transmitter terminals.

No Receive

Make sure AC adapter is securely plugged into electrical

outlet and into DC input connector on receiver rear

panel.

Receiver RF indicator glows

Turn the receiver ON.

Turn up the Gain adjustment switch in the transmitter.

Check the power connection of the receiver

and ampliﬁer or mixer.

Receiver RF indicator OFF,

transmitter ON

Check the receiver and transmitter whether use the

same channel.

Take the receiver away from any metal object.

Check the line of sight between receiver and transmitter.

Move the transmitter closer to the receiver.

The battery power indicator

light ﬂashes Replace transmitter batteries.

Distortion or

unwanted noise bursts

Receiver display indicators

antenna activity

Remove nearby sources of RF interference (CD players,

computers, digital effects, in-ear monitor systems, etc.).

Distortion level

increases gradually

Receiver RF indicator OFF,

transmitter ON Replace transmitter batteries.

Sound level different

from cabled guitar or

microphone, or when

using different guitars

Adjust transmitter gain and receiver volume as

necessary.

Owner’s manual | WiP 160/160C Wireless Microphone Systems WiP 160/160C Wireless Microphone Systems | Owner’s manual

ENGLISH

SPECIFICATIONS

SYSTEM

Frequency Range and Transmitter Output level

RECEIVER

Operating Range under Typical Condition: 50m (150 ft.)

Note: actual range depends on RF signals

absorption, reﬂection and interference.

∙

Audio Frequency Response (±3 dB): 60Hz÷16kHz

∙

TotalHarmonicDistortion(±30kHzdeviation,1kHztone):<1%

∙

Dynamic Range: >90 dB (A weighted)

∙

Operating Temperature Range: -10°C to +50°C

Note: battery characteristics may limit the range.

∙

Audio Output Level Maximum (ref. ±30 kHz, 1 kHz)

1/4” connector ( 3kΩ load): –18dBV

∙

Output Impedance: 1/4” connector 1kΩ

∙

Sensitivity (intermediate frequency adjustment audio

noise output: < –90dBm

∙

Image Rejection: >60dB

∙

Dimensions (WxHxD): 210x116x42 mm

∙

Power Requirements: 12/18V DC @300mA, supplied by

external power supply

Band Range Transmitter RF level

UB 630÷660 MHz 13dBm

HANDHELD TRANSMITTER

∙

Audio Input Level maximum: 0dBV

∙

Dimensions(includingthemicrophone):245xø47 mm

∙

Weight: 195g

∙

BatteryType:2xAAAlkalineorrechargeable batteries.

∙

Battery Life: >10 hours (Alkaline)

BODY PACK TRANSMITTER

∙

Audio Input Level Maximum: 0dBV ~ +20dBV

∙

Gain adjustment Range: 20dB

∙

Input Impedance: 470kΩ

∙

Dimensions (WxHxD): 65x105x23 mm

∙

Weight: 80g without batteries

∙

Power Requirement: 2 x AA-size Alkaline

or rechargeable batteries

∙

Battery life: >10 hours (Alkaline)

W iP 160/160 C

Manuale d’uso | WiP 160/160C Sistema UHF senza ﬁli WiP 160/160C Sistema UHF senza ﬁli | Manuale d’uso

ATTENZIONE

Nell’interesse della propria e della altrui sicurezza,

e per non invalidare la garanzia, si raccomanda una

attenta lettura di questa sezione prima di utilizzare

il prodotto.

∙ Leggete tutta la documentazione prima di utilizzare

l’apparecchiatura.

∙ Conservate tutta la documentazione per ogni ulteriore

consultazione, fornendola ad eventuali utilizzatori.

∙ Osservate tutte le avvertenze e seguite tutte le istruzioni

contenute in questo manuale di istruzioni.

∙ Danni causati da errata connessione a tensione alternata

non sono coperti da garanzia. La tensione di rete deve

corrispondere all’etichetta posteriore.

∙ Utilizzate sempre l’unità con il cavo di massa di corrente

collegato alla terra dell’impianto elettrico. Prendete

precauzioniper evitare unamessa aterra difettosa,scorretta

o inefﬁciente.

∙ Pulite i dispositivi solo quando non sono collegati alla rete

elettrica. Per la pulizia usate un panno asciutto.

∙ Per ridurre il rischio di incendi o scosse elettriche, non

utilizzate i dispositivi e gli alimentatori vicino all’acqua e

non esporli alla pioggia o all’umidità. .

∙ Utilizzare esclusivamente l’alimentatore in dotazione,

scollegandolo durante i temporali o se inutilizzato per

lunghi periodi di tempo.

∙ Per prevenire surriscaldamento, i dispositivi devono

esser distanti da fonti di calore (radiatori, caloriferi, stufe

ampliﬁcatori o altri apparecchi) né esser esposti alla luce

diretta del sole.

∙ Perl’assistenzarivolgersiapersonalequaliﬁcato.L’assistenza

è necessariase idispositivisonostati danneggiatiinqualsiasi

modo, seall’internoèstatoversato del liquidoo sonocaduti

oggetti, i dispositivi sono stati esposti a pioggia o umidità,

non funzionino correttamente o sono caduti.

NOTA BENE

Per qualsiasi intervento di manutenzione o riparazione,

rivolgetevi alla Elettronica Montarbo srl e/o a personale

altamente qualiﬁcato speciﬁcamente segnalato da questa.

Direttiva RAEE

ATTENZIONE!

Il prodotto è contrassegnato da questo simbolo che

segnala di non smaltire le apparecchiature elettriche ed

elettroniche tramite la normale procedura di smaltimento

dei riﬁuti domestici. Per questi prodotti è previsto un sistema

di raccolta differenziato in conformità alla legislazione che richiede il

trattamento, il recupero e il riciclaggio adeguato dei suddetti prodotti. Per

maggiori informazioni si prega di contattare l’autorità locale competente.

La barra nera sotto il simbolo indica che il prodotto è stato immesso sul

mercato dopo il 13 agosto 2005.

INFORMAZIONI PER UN CORRETTO SMALTIMENTO

Per gli utenti privati

Nell’Unione europea | Attenzione: Per smaltire il presente dispositivo,

non utilizzare il normale bidone della spazzatura! Le apparecchiature

elettriche ed elettroniche usate devono essere gestite a parte e in

conformità alla legislazione che richiede il trattamento, il recupero e il

riciclaggio adeguato dei suddetti prodotti. In seguito alle disposizioni

attuate dagli Stati membri, i privati residenti nella UE possono conferire

gratuitamente le apparecchiature elettriche ed elettroniche usate a centri

di raccolta designati*. In alcuni paesi (*), anche il rivenditore locale

può ritirare gratuitamente il vecchio prodotto se l’utente acquista un

altro nuovo di tipologia simile. *Per maggiori informazioni si prega di

contattare l’autorità locale competente.

In paesi che non fanno parte dell’UE | Contattare le autorità locali e

informarsi sul metodo di smaltimento corretto.

In Svizzera | Le apparecchiature elettriche o elettroniche usate possono

essere restituite gratuitamente al rivenditore, anche se non si acquista un

prodotto nuovo. Altri centri di raccolta sono elencati sulle homepage di

www.swico.ch o di www.sens.ch.

Per gli utenti professionali

Nell’Unione europea | Attenzione: Se il prodotto è impiegato a scopi

professionali, procedere come segue per eliminarlo: contattare il proprio

rivenditore FiveO by Montarbo®che fornirà informazioni circa il ritiro del

prodotto. Potrebbero essere addebitate le spese di ritiro e riciclaggio.

Prodotti piccoli (e quantitativi ridotti) potranno essere ritirati anche dai

centri di raccolta locali.

In Spagna | Contattare il sistema di raccolta ufﬁciale o l’ente locale

preposto al ritiro dei prodotti usati.

In paesi che non fanno parte dell’UE | Contattare le autorità locali e

informarsi sul metodo di smaltimento corretto.

aVVertenZe

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Manuales populares de Sistema de micrófono de otras marcas

Paso

Paso R824 Manual de usuario

Naxa

Naxa NAM-982 Manual de usuario

Motorola

Motorola PMNN4461 Manual de usuario

Xvive

Xvive U3 Manual de usuario

Tekon

Tekon DUOS Manual de usuario

Heyuan Intelligence

Heyuan Intelligence IOT-G2S-01 Manual de usuario

Devine

Devine WMD-IE Manual de usuario

LG LF-D7150 Manual de usuario

GE S768DAV Manual de usuario

LD U305 HBH 2 Manual de usuario

Chainway

Chainway URA8 Manual de usuario

ORATOR

ORATOR D860TD Manual de usuario

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Manual de usuario

Alpha Technologies

Alpha Technologies RBMS Manual de usuario

SWIT Electronics Co.,LTD.

SWIT Electronics Co.,LTD. CW-S150 Manual de usuario

Shure

Shure UA844 Manual de usuario

Panasonic

Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manual de usuario

Pyle

Pyle PDWM5000 Manual de usuario