Fishman C-100 Manual de usuario

USER GUIDE

C-100

2

Welcome

Thank you for making Fishman a part of your acoustic experience. We are proud

to offer you the ﬁnest acoustic ampliﬁcation products available: high-quality

professional-grade tools which empower you to sound your very best.

Troubleshooting

If you are unfamiliar with this product, please pay close attention to the

requirements for installation. Failure to do so can result in permanent damage

to the pickup.

Installation by a qualiﬁed professional is strongly recommended.

Technical support, troubleshooting tips and installation information can be

found at http://www.ﬁshman.com/support/

3

Installation

1. Measure the opening of the bass side wing slot on the bridge with a vernier

caliper. The opening should be between .060” and .090” (1.5mm and 2.3mm) for

proper ﬁt.

If the wing slot opening of the cello measures more than .090” (2.3mm), the leg

facing the pickup must be shimmed. For that purpose, we have provided a strip

of wooden shim material that can be easily cut with scissors, stacked and glued

to produce a shim of any required thickness.

4

2. Slide the transducer into the bass wing slot as shown. Make certain that the

sensing element is in contact with the wing face and that the spring (made of

tempered beryllium copper) is in contact with the corresponding “leg” face of

the bridge.

Note: For best performance, the wing

slot opening should be .070” (1.8mm).

3. For permanent installation, use any

appropriate wood adhesive to bond the

shims to the face of the bass side wing. As

a result, the shims will be located between

the transducer’s sensing element and the

bass side wing.

Note: The performance of the C-100 is

affected by the amount of contact area

between its sensing element and the wing

face of the bridge. Accordingly, the perfor-

mance may be adversely affected if the wing

face has been stylized or carved in any way.

5

4. Once the transducer is properly inserted into the

bridge, the next step is to mount the adhesive-backed

jack mount to the back side of the tailpiece. First, peel

off the release ﬁlm from the holder and then press the

holder ﬁrmly in place below the ﬁne tuning machines

of the tailpiece. Position the holder so that the jack,

when slipped into the holder, will be at a right angle

(90°) to the tailpiece.

5. Insert the jack into the holder and snap shut. Since the

wire is somewhat microphonic, it should not be allowed

to lie on the face of the instrument.

6

Fine Tuning

Once the C-100 is properly mounted, plug the instrument into an ampliﬁer and

play at a low volume. Carefully shift the position of the C-100 within the slot and

listen for the best location.

Note: If installation is to be permanent, a small drop of cyanoacrylate adhesive

on the spring side (lower face) of the transducer can be used.

7

Plugging In

An impedance matching preamp is recommended, but not required. This will

help realize the full frequency response potential of the pickup and allow for

cable runs longer than 10 feet without signal deterioration. Use a high quality,

low capacitance ¼” shielded instrument cable. This will ensure minimal tone

coloration and hum.

WWW.FISHMAN.COM

009-015-002 Rev C 4-09

Tabla de contenidos

Otros manuales de Equipo de música de Fishman

Fishman

Fishman RARE EARTH - Manual de usuario

Fishman

Fishman NASHVILLE SERIES PICKUP Manual de usuario

Fishman

Fishman V-200 PROFESSIONAL VIOLIN PICKUP Manual de usuario

Fishman

Fishman M-200 PROFESSIONAL MANDOLIN PICKUP Manual de usuario

Fishman

Fishman ELLIPSE VT - Manual de usuario

Fishman

Fishman ELLIPSE BLEND - Manual de usuario

Fishman

Fishman TriplePlay Guía de configuración

Fishman

Fishman FULL CIRCLE UPRIGHT BASS PICKUP Manual de usuario

Fishman

Fishman POWERBRIDGE PICKUP Manual de usuario

Fishman

Fishman VTB Manual de usuario

Fishman

Fishman ELLIPSE VT - Manual de usuario

Fishman

Fishman MODEL TSV Manual de usuario

Fishman

Fishman ELLIPSE BLEND - Manual de usuario

Fishman

Fishman ELLIPSE VT - Manual de usuario

Fishman

Fishman ELLIPSE AURA - Manual de usuario

Fishman

Fishman FULL CIRCLE Manual de usuario

Fishman

Fishman MATRIX INFINITY - Manual de usuario

Fishman

Fishman VTB Manual de usuario

Fishman

Fishman NASHVILLE M-300 Manual de usuario

Fishman

Fishman VS-50P POWERBRIDGE - ROUTING Manual de usuario

Fishman

Fishman INK PLUS Manual de usuario

Fishman

Fishman NATIONAL STYLE RESOPHONIC GUITAR PICKUP Manual de usuario

Fishman

Fishman FLUENCE Manual de usuario

Fishman

Fishman CLÁSICA II Manual de usuario

Manuales populares de Equipo de música de otras marcas

DAPAudio

DAPAudio IPS-PT Manual de usuario

Dynacord

Dynacord DPM 8016 Manual de usuario

Subdecay

Subdecay Starlight Flanger Manual de usuario

Moen

Moen GEC8 Live Manual de usuario

Fender

Fender 1 Manual de usuario

Yamaha

Yamaha MLC-16 Manual de usuario

Sonuscore

Sonuscore TIME TEXTURES Manual de usuario

flight of harmony

flight of harmony V'Amp Manual de usuario

NANO

NANO PERFORMANCE MIXER Manual de usuario

Tascam

Tascam CD-GT2 Manual de usuario

BHI

BHI NEIM 1031 MKII Manual de usuario

Befaco

Befaco KICKALL Manual de usuario

Paia

Paia 9720 Guía

limex

limex ALPIN MASTER 128 Manual de usuario

nord

nord Electro 3 Manual de usuario

Joemeek

Joemeek sixQ2 Manual de usuario

CARVIN

CARVIN 500W STEREO POWER MODULE - SCHEMA REV G Manual de usuario

Furutech

Furutech ADL GT40 Guía de instalación