Fisher-Price B1637 Manual de usuario

-p

Model Number: B1637

PLEASE KEEP FOR FUTURE REFERENCE.

Please read these instructions before assembly and use of this product, as they contain important information.

Adult assembly is required.

Tools needed for assembly: Phillips Screwdriver and Scissors (both not included).

Requires four “D” (LR20) alkaline batteries for swinging and sound operation;

three “AA” (LR6) alkaline batteries for sound ‘n lights tray operation; and

three “AAA” (LR03) alkaline batteries for remote operation (all batteries not included).

Maximum Weight Limit: 24 lbs. (10.9 kg).

IMPORTANT! The maximum weight limit for this product is 24 lbs. If your child weighs

less than 24 lbs., but is really active and appears to be able to climb

out of the swing, immediately discontinue its use.

Deluxe Quick Response Swing

with Remote Control

Occasionally a consumer may experience a problem with

one of our products. If this should happen, please call us

toll-free, rather than return this product to the store. Usually,

we can solve the problem over the telephone or send you

replacement parts. Please call Fisher-Price® Consumer

Relations, toll-free at 1-800-432-5437,8AM - 6 PM EST

Monday through Friday. Hearing-impaired consumers using

TTY/TDD equipment, please call 1-800-382-7470.

Or, write to:

Fisher-Price®

Consumer Relations

636 Girard Avenue

East Aurora, New York 14052

•To prevent serious injury or death

from falls and being strangled in

the restraint system:

- Always use the restraint sys-

tem. Never rely on the tray to

restrain child.

- Never use with an active child

who may be able to climb out of

the seat.

•Never leave child unattended.

WARNING

This product contains small parts

in its unassembled state.

Adult assembly is required.

CAUTION

Consumer InformationWa rnings and Caution

Parts

Front Base

Rear Base

Housing

2 Rear Legs

(Shorter)

Motor Housing

Seat with Restraint

2 Seat Tubes

Bracket

(with M4 Lock Nuts)

Seat Wire

2 Seat Wire

Caps

2 Accessory Bins

Pad

Sound ‘n

Lights Tray

Mirror Base

Remote Control

and Holder

(with M4 Lock Nut)

Tray

2 Front Legs

(Longer)

M4 Screw - 4

Shown Actual Size

Note: Tighten or loosen all screws and bolt with a Phillips screwdriver. Do not over-tighten the screws.

#8 x 13/8" Screw - 10

Shown Actual Size

#6 x 5/8" Screw - 4

Shown Actual Size

M4 Bolt - 1

Shown Actual Size

•Place the front base on a flat surface.

•Position a front leg (longer) so that the tapered end is

downward, as shown.

•While pressing the button on one of the front legs, insert it

into the front base. Push down on the front leg until the

button “snaps” into the hole in the front base.

•Repeat this procedure to assemble the other front leg to

the front base.

Front Base

Tapered End

Front Legs

(Longer)

IMPORTANT!

Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use

if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts.

Assembly

•Using scissors, remove the ribbon connecting the remote

and the holder.

Press

Button

Press

Button

Remote

Holder

Ribbon

•While standing on the front base, pull the front legs up.

The front legs should remain secured to the front base.

If you can remove the front legs, you have not assembled

them correctly to the front base. Reread and repeat

assembly step 1.

Front Legs Pull Up

Pull Up

Front Base

•Position the holder so that the

open end faces forward, as shown.

•Slide the holder onto the front leg with a hole.

Holder

Front

Leg Hole

Shown Actual Size

M4 Lock Nut

Rounded

Side

M4 Lock Nut

(Rounded

Side Out)

Hexagonal Opening

Hint: An M4 lock nut has been assembled to the holder at

the factory. During shipment of this product, it may have fallen

out. Check to be sure there is a lock nut in the hexagonal opening

on the holder. If it has fallen out, fit the lock nut back into the

hexagonal opening. Make sure the rounded side of the lock nut

faces out.

Assembly

• Position a rear leg so that the tapered end is upright.

•While pressing the button on the top of the rear leg, insert it

into the housing short tube, as shown. Push the rear leg until

the button “snaps” into the hole in the short tube.

•Repeat this procedure to assemble the other rear leg to the

motor housing short tube.

•Pull the rear legs down to be sure they are secure in the

housings. If you can remove them, you have not assembled

them correctly. Please re-read and repeat this assembly step.

Button

Rear Legs

Motor Housing

Short Tube

•Fit the bottom of the remote into the cupped portion of

the holder.

•Push to “snap” the top of the remote under the holder clips.

Holder

•Position the holder so that the hole in the holder aligns with

the hole in the front leg.

•Insert the M4 bolt through the holder, front leg and into the

lock nut. Tighten the bolt.

Holder

Front Leg

Tapered

End

• Position the housing so that the hub is inward.

•While pressing the button on the top of a front leg, insert it

into the housing slot, as shown. Push the front leg until the

button “snaps” into the hole in the housing.

•Repeat this procedure to assemble the motor housing to

the other front leg.

•Pull the front legs down to be sure they are secure in the

housings. If you can remove them, you have not assembled

them correctly. Please re-read and repeat this assembly step.

Press

Buttons

Front

Legs

Motor

Housing

Hole

Housing Hub

Slot

Clips

Remote

M4 Bolt

Shown Actual Size

•Place the rear base on a flat surface so that the buttons

face the front base.

•While pressing the buttons on each side of the rear base,

fit the rear legs onto the rear base. Push the rear legs down

until the buttons on the rear base “snap” into the holes

in each rear leg.

Rear Base

Front

Base

Rear

Legs

Assembly

•While standing on the rear base, pull the rear legs up.

They should remain secured to the rear base. If you can

remove the rear legs, you have not assembled them cor-

rectly to the rear base. Reread and repeat assembly step 10.

•Set the frame assembly aside for Assembly step 21.

•Position the seat face down, with

the top of the seat facing you.

•Position a seat tube so that the long

end is upright and toward you and the curved end is toward

the outside edge of the seat.

•Insert the curved end of the seat tube through the holes in

the ridges on the seat back.

•Repeat this procedure to assemble the other seat tube to

the seat.

Press

Button

Press

Button

Rear Legs

Pull Up

Rear Base

Top of Seat

Seat Tube

Long Ends

Ridges

Curved

End

•Pull both rear legs out until they “snap” into place.

Pull

Rear

Leg

Pull

Rear

Leg

•Insert four M4 screws into the seat tubes and tighten.

Assembly

•Rotate the seat tubes down.

•Fit the seat wire through the slot in the bracket as shown.

Seat

Tubes

Bracket

Bracket Slot

Seat Wire

Seat Tubes

•Position the bracket so that the tall end is toward the

bottom edge of the seat.

Hint: The M4 lock nuts have been assembled to the bracket at

the factory. During shipment of this product, they may have

fallen out. Check to be sure there is a lock nut in each hexagonal

opening on the bracket. If one (or more) has fallen out, fit the lock

nut into a hexagonal opening in the bracket. Make sure the

rounded side of the lock nut is facing up.

•Fit the grooves on the bracket to the seat tubes, as shown.

Seat

Tubes

Bracket

Grooves

Tall

End

Bottom

Edge of

Seat

M4 Screw - 4

Shown Actual Size

Lock Nut

Hexagonal

Opening

Shown Actual Size

M4 Lock Nut

Rounded Side

•While holding the seat wire in place, carefully turn the

seat around so that the front of the seat faces you.

•Position the seat wire cap so that the rounded edge

is upright.

•Fit each end of the seat wire through the hole in each

seat wire cap.

Ends of

Seat Wire

Assembly

•Turn the seat face down.

•Fit an accessory bin into the groove on each side of the

seat, as shown.

•Insert two #8 x 13/8" screws into each accessory bin

and tighten.

Seat Wire

Cap

Seat Wire

Cap

Grooves

Seat

Accessory Bin

•Lift the seat tubes slightly.

•With the seat wire hanging down, insert the ends of the seat

wire through the slots in the seat, as shown.

Slots

Seat Wire

#8 x 1

3/8

”Screw - 4

Shown Actual Size

Seat Wire

Cap Hole

Rounded Edge Up

•Press the seat wire caps

into place.

•Insert two #6 x

5/8"

screws

through each seat wire cap

and tighten.

Seat Wire

Caps

Seat Wire is

Through Hole in

Seat Wire Cap

Press in Place

#6 x 5/8" Screw - 4

Shown Actual Size

Hint: The seat wire caps are designed to fit into the seat only one

way. If the screw holes in the seat wire caps do not align with the

holes in the seat, try switching the seat wire caps onto the

opposite ends of the seat wire.

Assembly

•Fit the pocket on the back of the pad onto the seat back.

•Fit the waist belts through the smaller slots in the pad.

Waist Belts

Pad

Slot

•Lift the bottom of the pad.

•Insert the pad elastic loops through the holes in the

seat bottom.

•Insert the crotch belt through the slot in the pad.

•From under the seat, fit the elastic loops onto the tabs on

the seat bottom.

•Insert a #8 x 13/8" screw into each frame hub and tighten.

•Again, push down on the seat to be sure the seat is secured

to both frame hubs.

Frame

Hubs

Pad

Elastic

Loops

Holes

Crotch

Belt

•Position the seat assembly so that the front of the seat is

toward the curved front base.

•While pressing the buttons on the swing tubes, insert them

into the frame hubs. Push the swing tubes up until the

buttons “snap” into the hole in the frame hubs.

•Push down on the seat to be sure the seat is secured in

both frame hubs.

Swing

Tube

Front

of Seat

Curved

Front

Base

Push

Button

Frame Hub

Seat Bottom

#8 x 1

3/8

”Screw - 2

Shown Actual Size

•Position the lights ‘n sounds tray on a flat surface, with the

roller facing you.

•Position the mirror base, with the mirror toward you.

•Fit the mirror base onto the lights ‘n sounds tray.

•Turn the assembly over. Insert four #8 x 13/8" screws into the

bottom of the lights ‘n sounds tray and tighten.

Assembly is now complete.

Mirror Base

Lights ‘n

Sounds Tray

•Fit the bottom edge of the pad around the bottom edge

of the seat.

•Hook the elastic loops on each side of the pad to the peg

on the back of the accessory bins.

Elastic

Loop

Elastic

Loop

#8 x 1

3/8

”Screw - 4

Shown Actual Size

Battery Installation

•Locate the battery compartment door on the swing frame.

•Insert a coin into the battery compartment door and pry the

battery compartment door off of the swing frame.

•Insert four “D” (LR20) alkaline batteries as indicated inside

the battery compartment.

•Replace the battery compartment door.

Battery

Compartment

Door

Swing

Hint: When swinging, sound or power L.E.D. slows/dims/stops,

it’s time to replace the batteries! We recommend using alkaline

batteries for longer battery life.

AssemblyAssembly

Tabla de contenidos

Otros manuales de Columpio para bebés de Fisher-Price

Fisher-Price

Fisher-Price B3002 Manual de usuario

Fisher-Price

Fisher-Price M5660 Manual de usuario

Fisher-Price

Fisher-Price M7590 Manual de usuario

Fisher-Price

Fisher-Price C5859 Manual de usuario

Fisher-Price

Fisher-Price BMK14 Manual de usuario

Fisher-Price

Fisher-Price CMR62 Manual de usuario

Fisher-Price

Fisher-Price BMF35 Manual de usuario

Fisher-Price

Fisher-Price V3394 Manual de usuario

Fisher-Price

Fisher-Price FWK51 Manual de usuario

Fisher-Price

Fisher-Price C1384 Manual de usuario

Fisher-Price

Fisher-Price 79636 Manual de usuario

Fisher-Price

Fisher-Price Y8649 BMM27 Manual de usuario

Fisher-Price

Fisher-Price 79636 Manual de usuario

Fisher-Price

Fisher-Price GNM43 Manual de usuario

Fisher-Price

Fisher-Price B0639 Manual de usuario

Fisher-Price

Fisher-Price BFX34 Manual de usuario

Fisher-Price

Fisher-Price J7811 Manual de usuario

Fisher-Price

Fisher-Price G5914 Manual de usuario

Fisher-Price

Fisher-Price DRG43 Manual de usuario

Fisher-Price

Fisher-Price J4205 Manual de usuario

Fisher-Price

Fisher-Price FDH41 Manual de usuario

Fisher-Price

Fisher-Price C6410 Manual de usuario

Fisher-Price

Fisher-Price Y9422 Manual de usuario

Fisher-Price

Fisher-Price M6156 Manual de usuario

Manuales populares de Columpio para bebés de otras marcas

Hudora

Hudora Comfort Instrucciones de montaje

stilum

stilum seta Especificaciones técnicas

stilum

stilum volucris 2 Especificaciones técnicas

stilum

stilum patis2 Manual de usuario

Graco

Graco OASIS Manual de usuario

highwood

highwood Lehigh Porch Swing Manual de usuario

VERTBAUDET

VERTBAUDET 70334 0022 Manual de usuario

Blumfeldt

Blumfeldt Hollywood Manual de usuario

Graco

Graco Swing N' Bounce Manual de usuario

Oliver & Kids

Oliver & Kids 697793 Manual de usuario

Kids II

Kids II Bright Starts Safari Smiles 60403-ES Manual de usuario

Sunjoy

Sunjoy L-GZ330PCO-1 Manual de usuario

stilum

stilum simius2 Especificaciones técnicas

Summer

Summer CUDDLE ME Manual de usuario

IKEA

IKEA EKORRE Manual de usuario

Playcore

Playcore Swing-N-Slide TB 1539 Manual de usuario

Gilis

Gilis Bebe Stars Flora Manual de usuario

Trigano

Trigano TO605 Manual de usuario