Fisher-Price 79596 Manual de usuario

Model Number: 79595, 79596

Please keep this instruction sheet for future reference, as it contains important information.

Adult assembly is required.

Tools needed for assembly: Phillips Screwdriver and Adjustable Wrench (both not included).

Requires three “D” (LR20) alkaline batteries for operation (not included).

Maximum Weight Limit: 24 lbs. (10.9 kg.)

The maximum weight limit for this product is 24 lbs.

IMPORTANT! If your child weighs less than 24 lbs., but is really active and appears to be

able to climb out of the swing, immediately discontinue its use.

Swing

Cradle

Cradle Swing

’

™

…

Warnings and Caution

Parts

• To prevent falls, never use with

an active child who may be able

to climb out of the seat.

• Never leave child unattended.

• To prevent injury or death from

falls or sliding out, always use

restraint system. Never rely on

the tray to restrain child.

WARNING

This product contains small parts

in its unassembled state. Adult

assembly is required.

CAUTION

Motorized Frame

2 Lower

Legs

2 Upper Legs

Seat

2 Feet

2 Elbow

Feet

Tray

Mobile

Pad

Seat Tube

Activity Toy Bar

ALL SHOWN ACTUAL SIZE

#8 x 1/2" Pointed Screw - 2

M4 x 31.5 mm Bolt - 2

M4 Lock Nut - 2

#8 x 3/4" Pointed Screw - 2

Seat Tube

Arm

SHOWN ACTUAL SIZE

Assembly

Lower Leg

• Fit a foot onto the end of the lower leg.

• Insert a #8 1/2" pointed screw through the bottom of the

foot and into the lower leg.Tighten the screw with a

Phillips screwdriver. Do not over-tighten.

• Repeat assembly steps 1 and 2 to assemble the other

elbow foot and foot to the other lower leg.

• Position one of the lower legs so that the long portion

is down.

• Fit an elbow foot, with the cup side down, onto the bend

in the lower leg.

• Insert a #8 3/4" pointed screw through the bottom of the

elbow foot and into the lower leg.Tighten the screw with

a Phillips screwdriver. Do not over-tighten.

• Stand each lower leg upright, as illustrated.

• The elbow foot and foot should be flat against the floor.

IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges.

DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed.

Never substitute parts.

Foot

Cup

Side

Down

• Position an upper leg so that the red dot is upward.

• While pressing the button on the straight end of an

upper leg, insert the upper leg into a lower leg. Make

sure the button on the upper leg “snaps” into the hole

in the lower leg.

• Repeat this procedure to assemble the other upper leg

to the other lower leg.

Elbow Foot

Lower Leg Long Portion

Lower Leg

Elbow Foot

Foot

SHOWN ACTUAL SIZE

#8 x 3/4" Pointed Screw - 2

#8 x 1/2" Pointed Screw - 2

Correct Incorrect

Red Dot

Lower Leg

Upper Leg

Straight

End

Button

Hole

Assembly

• Position the motorized frame so that the battery

compartment is toward you.

• Position the tubes in the motorized frame so that they are

toward the outer edges. The holes in the tubes should be

visible through the notches in the motorized frame.

• Locate the Rand Lon the underside of each elbow foot.

The Rindicates the right leg. The Lindicates the left leg.

• While pressing the upper button on the right leg, fit it

into the tube in the motorized frame. Make sure the

upper button on the right leg “snaps” into the hole in

the tube.

• While pressing the button on the left leg, fit it into the

tube in the motorized frame. Make sure the button on

the left leg “snaps” into the hole in the tube.

• When the legs are assembled correctly to the tubes in the

motorized frame, you should not see the red dots.

Tube

Hole

Red Dot

Motorized Frame

• Stand the assembly upright. All four feet should be flat upon

the floor. Also, when standing behind the product, check for

an Lmarking on the left foot and an Rmarking on the

right foot.

• If the feet are not flat upon the floor, or the left and right feet

have been reversed, simply remove both legs and replace

them on the opposite tube in the motorized frame. Again,

check to be sure all four feet are flat upon the floor.

Feet

Button

Feet

Tubes

Hole

Motorized

Frame

Battery

Compartment

Hole

Elbow Foot

• Position the seat upright.

• Place the pad onto the seat with the

ruffle toward the top of the seat.

• Fold the top of the pad down. Insert the waist belts through

the slots in the pad. Make sure the waist belts are not twisted.

• Insert the two elastic loops on the pad through the holes in

the seat bottom.

• Fold the bottom of the pad up. Insert the crotch belt through

the slot in the pad. Make sure the crotch belt is not twisted.

Seat

Elastic

Loops

Waist

Belts

Pad

Crotch Belt

Assembly

• While holding the elastic loops in place, turn the seat

face down.

• Hook the elastic loop on the left side onto the peg on the

right side.

• Hook the elastic loop on the right side onto the peg on the

left side.

• While pressing the button on the seat tube, slide the seat

tube arm onto the seat tube. Make sure the button on the

seat tube “snaps“ into the hole in the seat tube arm.

• Turn the seat upright.

• Fit the pad edges around the rim of the seat.

• Attach the two fasteners on each side of the pad to the

fasteners on each side of the seat.

Elastic Loop

Peg

Elastic Loop

Peg

Bottom View

Hint: The elastic loops should cross over each other when

attached correctly to the pegs.

Fasteners

Seat Tube

Button

Seat Tube

Arm Hole

• Insert an M4 x 31.5 mm bolt through the seat tube arm

and seat tube.

• Attach an M4 lock nut to the bolt. Make sure the rounded

side of the lock nut faces out.

• Using an adjustable wrench, hold the lock nut in place.

Then using a Phillips screwdriver, tighten the bolt. Do not

over-tighten.

M4 Lock Nut

Rounded

Side

M4 x 31.5 mm Bolt

Shown Actual Size

Assembly

Motorized

Frame Tube

Hole

• Press the button on the

seat tube and slide the

seat tube into the motor-

ized frame tube. Make sure

the button on the seat tube “snaps” into the larger hole in

the motorized frame tube.

• Insert a M4 x 31.5 mm bolt through smaller hole in the

motorized frame tube and into the seat tube.

• Attach an M4 lock nut to the bolt. Make sure the rounded

side of the lock nut faces out.

• Using an adjustable wrench, hold the lock nut in place.

Then, using a Phillips Screwdriver, tighten the bolt. Do not

over-tighten.

• Slide the button on the top of the mobile into the slot in

the motorized frame.

Assembly is now complete.

Seat Tube

Button

Slot

Mobile

• Turn the seat upright.

• Insert the tray tabs into the slots in each side of the seat.

• Insert the ends of the toy bar into the holes in the tray. Press

down on the ends of the toy bar to be sure they are secure.

Toy Bar

Tray

Slot

M4 x 31.5 mm Bolt

Shown Actual Size

M4 Lock Nut

Rounded

Side

Battery Installation Battery Tips

SHOWN ACTUAL SIZE

1.5V x 3

“D” (LR20)

Battery

Compartment

Door

Battery

Compartment

• Do not mix old and new batteries.

• Do not mix different types of batteries: alkaline, standard

(carbon-zinc) or rechargeable (nickel-cadmium).

• Remove the batteries during long periods of non-use.

Always remove exhausted batteries from this product.

Battery leakage and corrosion can damage this product.

Dispose of batteries safely.

• Do not dispose of batteries in a fire.The batteries may

expolde or leak.

• Never short-circuit the battery terminals.

• Non-rechargeable batteries are not to be recharged.

• Only batteries of the same or equivalent type as

recommended in the battery installation instructions

are to be used.

• If removable rechargeable batteries are used, they are only

to be charged under adult supervision.

• Rechargeable batteries are to be removed from the product

before they are charged.

• If you use a battery charger, it should be examined regularly

for damage to the cord, plug, enclosure and other parts.

Do not use a damaged battery charger until it has been

properly repaired.

Hint: We recommend using alkaline batteries for longer

battery life.

Hint: If the swinging motion becomes noticeably slower,

remove the batteries and replace them with three, new

“D” (LR20) alkaline batteries. Dispose of exhausted

batteries properly.

• Using a coin, press the tab on the battery compartment

door and remove it.

• Insert three “D” (LR20) alkaline batteries, as indicated

inside the battery compartment.

• Replace the battery compartment door.

Cradle and Swing Use

Your Cradle Swing changes from a traditional swing to a

rocking cradle at the push of a button!

IMPORTANT! Before each use or assembly, inspect this prod-

uct for damaged hardware, loose joints, missing parts or sharp

edges. DO NOT use if any parts are missing or broken. Contact

Fisher-Price® for replacement parts and instructions if needed.

Never substitute parts.

Side-to-side swinging motion soothes baby.

Head-to-toe swinging motion entertains baby.

Cradle

Swing

LegLeg

Button

• Firmly pull the legs outward. Make sure the buttons snap

into the notches in the motorized frame.

• Check to be sure the legs are locked into position by

pushing the legs inward. The legs should not move.

To Unfold

To prevent injury or death from

falls or sliding out, always use the

restraint system. Never rely on the

tray to restrain child.

WARNING

Cradle and Swing Use

Restraint Belts

• Place your child in the seat.

• Pull the crotch belt up between your child’s legs and

fasten both waist belts to the crotch belt. Make sure you

hear a “click” on both sides.

To tighten the waist belts:

• Feed the anchored end of the waist belt up through the

buckle to form a loop .

• Pull the free end of the waist belt .

• Repeat this procedure to tighten the other waist belt.

To loosen the waist belts:

• Feed the free end of the waist belt up through the buckle

to form a loop .

• Enlarge the loop by pulling on the end of the loop

toward the buckle.

• Pull the anchored end of the waist belt to shorten the

free end of the waist belt .

• Repeat this procedure to loosen the other waist belt.

Waist Belt Waist Belt

Crotch Belt

Power Settings

Power Dial

To start:

• Turn the power dial to the medium setting.The power

indicator lights.

• Give the seat a light push to start the swinging motion.

Adjust the power dial to the desired swing motion setting:

low, medium or high.

• Fit the tabs on the tray into the slots in the sides of the seat.

• To remove the tray, pull the tab out on one side of tray

and lift.

Tab

Slot

Using the Tray

Anchored End

Free End

To Tighten

Buckle

Anchored End

Free End

To Loosen

Hints:

- As with most battery-powered swings, a heavier child will

reduce the amount of swinging motion on all settings. In

most cases, the low setting works best for a smaller child

while the high setting works best for a larger child.

- If the low setting provides too much swinging motion for

your child, try placing one end of a blanket underneath

your child and let the other end of the blanket drape down

while swinging.

Cradle Swing Swing

Cradle and Swing Use

Adjust Positions

You can adjust the seat tube to three different positions:

• Press the seat tube button to unlock the seat tube.

• Rotate the seat tube to the desired position.

Adjust to Recline or Upright Positions

You can adjust the seat to two different positions:

Recline or Upright.

• From behind the seat, press both seat position buttons.

• Push the seatback up until the buttons “snap” into the

upright position.

• Push the seatback down until the buttons “snap” into

the recline position.

Seat Tube Button

Seat Tube

Front Edge

of Seat

Press Seat

Position Buttons

Upright

Recline

• Press the buttons on the back of the motorized frame while

pushing the legs inward.

Button Button

Storage

• Lean the Cradle Swing frame against a wall for storage.

IMPORTANT! Remove the batteries for long-term storage.

Hint: The legs may be disassembled for long-term storage.

Simply press the buttons on the legs and remove the upper and

lower legs.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Columpio para bebés de Fisher-Price

Fisher-Price

Fisher-Price J6294 Manual de usuario

Fisher-Price

Fisher-Price 79636 Manual de usuario

Fisher-Price

Fisher-Price X7324 Manual de usuario

Fisher-Price

Fisher-Price B3002 Manual de usuario

Fisher-Price

Fisher-Price Ocean Wonders Aquarium 79667 Manual de usuario

Fisher-Price

Fisher-Price K7192 Manual de usuario

Fisher-Price

Fisher-Price V1179 Manual de usuario

Fisher-Price

Fisher-Price G8661 Manual de usuario

Fisher-Price

Fisher-Price 79647 Manual de usuario

Fisher-Price

Fisher-Price V4874 Manual de usuario

Fisher-Price

Fisher-Price J7811 Manual de usuario

Fisher-Price

Fisher-Price HBM78 Manual de usuario

Fisher-Price

Fisher-Price K6077 Manual de usuario

Fisher-Price

Fisher-Price 79321 Manual de usuario

Fisher-Price

Fisher-Price B9758 Manual de usuario

Fisher-Price

Fisher-Price C5859 Manual de usuario

Fisher-Price

Fisher-Price SWING 'N MEALS 79739 Manual de usuario

Fisher-Price

Fisher-Price HBT17 Guía de configuración rápida

Fisher-Price

Fisher-Price W9510 Manual de usuario

Fisher-Price

Fisher-Price BGB34 Manual de usuario

Fisher-Price

Fisher-Price BO639 Manual de usuario

Fisher-Price

Fisher-Price X7037 Manual de usuario

Fisher-Price

Fisher-Price X7046 Manual de usuario

Fisher-Price

Fisher-Price CMR46 Manual de usuario

Manuales populares de Columpio para bebés de otras marcas

Hudora

Hudora Comfort Instrucciones de montaje

stilum

stilum seta Especificaciones técnicas

stilum

stilum volucris 2 Especificaciones técnicas

stilum

stilum patis2 Manual de usuario

Graco

Graco OASIS Manual de usuario

highwood

highwood Lehigh Porch Swing Manual de usuario

VERTBAUDET

VERTBAUDET 70334 0022 Manual de usuario

Blumfeldt

Blumfeldt Hollywood Manual de usuario

Graco

Graco Swing N' Bounce Manual de usuario

Oliver & Kids

Oliver & Kids 697793 Manual de usuario

Kids II

Kids II Bright Starts Safari Smiles 60403-ES Manual de usuario

Sunjoy

Sunjoy L-GZ330PCO-1 Manual de usuario

stilum

stilum simius2 Especificaciones técnicas

Summer

Summer CUDDLE ME Manual de usuario

IKEA

IKEA EKORRE Manual de usuario

Playcore

Playcore Swing-N-Slide TB 1539 Manual de usuario

Gilis

Gilis Bebe Stars Flora Manual de usuario

Trigano

Trigano TO605 Manual de usuario