Firstech 2W902R-SP Manual de usuario

Remote & Antenna FCC ID Number (US Only) IC ID Number (International Only)

2W902R-SP VA5REC500-2WSP 7087A-2WREC500SP

ANT-2WSP VA5A1000-2WSP 7087A-2WA1000SP

User Manual

By Firstech LLC, Version: 1.0

Applicable to the following remote(s);

2W902R-SP 2 Way 5 Button LED Remote

ANT-2WSP 2Way Antenna

This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions;

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following conditions;

(1) This device may not cause harmful interference.

(2) This device may accept any interference received, including interference that may cause undesired operation.

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate this device.

WWW.COMPUSTAR.COM

Introduction ..................................................................................................................................................3

Warranty Coverage......................................................................................................................................3

Quick Reference...........................................................................................................................................4

Button Lock.................................................................................................................................................4

Full or Half Paging Mode............................................................................................................................4

Valet Mode..................................................................................................................................................4

Remote Maintenance – Battery Replacement...........................................................................................4

2 Way Remote Button Functions...............................................................................................................5

Function Button Menu ................................................................................................................................6

Remote Option Menu Table.......................................................................................................................6

Remote LED Functions and Descriptions.................................................................................................6

Alarm LED Notifications..............................................................................................................................7

1 Way Remote Button Functions...............................................................................................................7

General System Functions .........................................................................................................................8

Sending Commands ...................................................................................................................................8

Receiving Commands.................................................................................................................................8

Active Lock/Arm and Unlock/Disarm..........................................................................................................8

Passive Lock/Arm.......................................................................................................................................8

Automatic Transmission Remote Start Function.......................................................................................9

Manual Transmission Remote Start Function (Reservation Mode)..........................................................9

Trunk Release......................................................................................................................................... 10

Auxiliary Outputs/Window Roll-Down/Sliding Doors............................................................................... 10

Silent Arm/Disarm.................................................................................................................................... 10

Remote Mute........................................................................................................................................... 11

Shock Sensor On/Off .............................................................................................................................. 11

Automatic Button Lock ............................................................................................................................ 11

Advanced System Functions................................................................................................................... 12

Drive Lock/Ignition Controlled Door Locks.............................................................................................. 12

Turbo Timer Mode................................................................................................................................... 12

2nd Car Mode (Multiple Vehicle Control) ................................................................................................. 12

RPS Touch and RPS (Remote Paging Sensor)..................................................................................... 12

Secure Valet Switch ................................................................................................................................ 15

Timer Start Mode..................................................................................................................................... 15

Cold/Hot Start Mode................................................................................................................................ 15

Remote Coding / Programming Routine................................................................................................ 16

Programming 2 Way 5 Button Remotes: ................................................................................................ 16

Remote Start Error Diagnostic................................................................................................................ 16

Alarm Diagnostic....................................................................................................................................... 17

Limited Lifetime Warranty........................................................................................................................ 18

Introduction

Thank you for purchasing a Firstech system for your vehicle. In order to truly enjoy the benefits of this

system, we recommend that you thoroughly review the following manual. Please note that this manual

applies to the 2 Way 5 Button LED Remote (2W902R-SP) Regardless of whether you purchased the

ALARM IT, START IT, or MAX IT system. This manual also supports the 1WG7R-SP that is included in

your new RF Kit. Please note that there are certain features listed in this manual that may not be

available for your system. There may also be features listed in this manual that require additional

installation or programming before they become active. If you have any questions or concerns please

contact the original place of purchase. For further information you may also contact our customer support

center at 888-820-3690.

Warranty Coverage

Caution: The Manufacturer’s warranty will be voided if this product is installed by anyone other than an

Authorized Firstech dealer. For complete warranty details visit www.compustar.com or the last page of

this manual. Firstech remotes carry a 1 year warranty from original date of purchase. CompuStar Pro

remotes carry a 2 year warranty.

Warranty registration can be completed online by visiting www.compustar.com. Please complete the

registration form within 10 days of purchase. We do not include a mail in warranty registration card with

each unit – registration must be done online. To verify that an authorized dealer installed your system,

we highly recommend that you keep a copy of the original proof of purchase, such as the dealer invoice

in a safe place.

Quick Reference

Button Lock

The 2W902R-SP comes equipped with automatic button lock. This requires you to tap any button to

wake your remote up then tap the button for the function you are trying to activate. Button lock can be

turned off in your remote’s option menu.

Full or Half Paging Mode

The 2W902R-SP is shipped in Half Paging Mode. This means that the remote will only receive 2 Way

LED confirmations for remote start and lock and unlock. It will not receive 2 Way LED confirmations

when the alarm is triggered. To turn this feature on hold the buttons for 2.5 seconds to

enter the Remote Programming Menu. Tap the Lock <insert lock button icon> button to turn Full Paging

on. The remote will beep twice and LED flash red. You are now in Full Alarm and Starter Mode.

Valet Mode

When servicing or loaning your vehicle to others, the system should be placed in Valet Mode. Valet

Mode prevents the system from remote starting and disables all alarm functions. IMPORTANT: While in

Valet mode the remote will still control power lock and unlock systems. The parking lights will not flash.

The system can be put into valet one of three ways:

1. Turn the vehicle’s key to the ignition “on” position, tap the Function and Trunk buttons

<insert function + trunk button icons> at the same time for a half second. The parking lights

will flash once and/or siren chirp once to confirm the system is in valet mode. Repeat this process to take

the system out of valet mode. The parking lights will flash twice and/or siren chirp once to confirm the

system is out of valet mode. Please note the confirmation chirps from the 2 Way remote will be quieter in

Valet Mode.

2. If you do not have your remote control, you can put the system into valet by turning the ignition key

“on” and then “off” five times within 7 seconds. The parking lights will flash once to confirm the system is

in valet mode. Shortly after the first flash, the parking lights will flash twice. A remote control is required

to take the system out of valet mode.

3. If your system is set up for a secure valet option (optional), you will not be able to put the system into

valet until the proper code has been entered using the secure valet switch. The secure valet switch is the

small button with bright blue LED on the front and if installed is the only way to override the alarm and/or

remote start. Until programmed, the default code is (3, 3).

Removing System Out of Valet:

Tap the<insert function + trunk button icons> for a half second to remove the system out of Valet. On

starter and alarm/starter systems, you can turn the key to the Ignition On position and tap the foot brake

10 times. This will take your system out of Valet Mode. If this does not work you can also reprogram your

remote(s). See Remote Coding/Programming Routine section for details.

Remote Maintenance – Battery Replacement

The only regular maintenance this system requires is remote control battery replacement. No

programming is required when replacing the battery.

2W902R-SP:

Turn the remote over and unlock the battery cover by sliding the clear tab up. Slide the battery cover off,

revealing the AAA battery. IMPORTANT: Be sure to observe correct polarity when installing the battery.

1WG7R-SP:

Use a quarter or flat head screwdriver to pry the back cover off of the remote. You can insert the quarter

or flat head in the small slot at the bottom of the remote by the keychain loop. Carefully pry off the back

cover using caution that you do not damage the circuit board. Your battery size should be listed on the

battery. Battery size: Two (2) CR2016) Replacements can be purchased from your local Firstech dealer

or an electronics store.

2 Way Remote Button Functions

Button Duration Function / Description

<Insert

Lock

Icon>

Half

second Locks doors and if equipped, arms the alarm.

seconds Panic/vehicle locater (flashes vehicle’s parking lights and sounds siren and horn).

<Insert

Unlock

Icon>

Half

second Unlocks doors and if equipped, disarms the alarm.

2.5

seconds Run time extender. Resets the run time for Turbo Timer or Remote Start.

<Insert

Trunk

Icon>

2.5

seconds Trunk release. Triggers the trunk release output and opens the vehicle’s trunk.

<Insert

Key

Icon>

Half

second Car Check (updates vehicle status on remote) / Secure Auxiliary

2.5

seconds Holding this button will start your vehicle. Repeat and this will shut your vehicle down.

<Insert

Function

Icon>

This button activates and deactivates multiple features. See the Function Button Menu table below for

complete details.

<Insert

Lock +

Unlock

Icon>

Half

second Turns siren chirps on/off (Note: With the siren chirps off, it will still sound in the event the

alarm is triggered).

2.5

seconds Turns the shock sensor on/off. (ALARM IT or MAX IT systems only)

<Insert

Function

and

Trunk

Icon>

Half

second Valet mode (see Valet Mode Section for details)

2.5

seconds Option programming menu 1. For use during installation.

<Insert

Function

and Key

Icon>

Half

second Activates timer start mode. Timer start mode has multiple programmable settings: duration

settings, temperature settings and self start settings.

2.5

seconds Option programming menu 2. For use during installation.

<Insert

Trunk Half

second Activates passive arming (vehicle will arm/lock 30 seconds after the vehicle is disarmed)

and Key

Icon> 2.5

seconds Accesses Remote Option Menu. See Remote Option Menu Table for details.

Function Button Menu

Button Duration <Insert Lock

Icon> <Insert Unlock Icon> <Insert

Trunk

Icon>

<Insert

Key/Start

Icon>

<Insert

Function

Icon>

One Tap Drive Lock

On/Off Turbo Timer On/Off Auxiliary 1 Auxiliary 2

Remote Option Menu Table

Feature Turns Feature

On or Off Button

Duration Remote

Chirp(s) Function / Description

Enter and Exit

Remote Menu

<insert Trunk

+ Key button

icon>

2.5

Seconds Three On |

Three Off Enters and Exits Remote Option Menu. The LED will flash purple.

2 Way Paging

Display <insert Lock

icon> Half

second

One-Half

Paging | Two-

Full Paging

Determines whether your remote is used for Alarm or Start Only

system. Set it to FULL for ALARM IT and MAX IT features. Set to

HALF for START IT ONLY systems. If on, LED will flash blue.

When turned off, the LED will flash red twice.

Important: The 2W902R-SP is defaulted in HALF for START IT

systems. It must be changed to FULL for alarm systems.

Silent <insert Unlock

icon> Half

second One On | Two

Off Turns the silent mode on or off. If on, LED will flash blue. When

turned off, the LED will flash red twice.

2nd Car Mode <insert Trunk

icon> Half

second One On | Two

Off

Puts your remote into 2nd Car Mode. You can control another

vehicle with the same remote as long as it has the same RF Kit

installed. If on, LED will flash blue. When turned off, the LED will

flash red twice.

Automatic Button

Lock

<insert

Key/Start

icon>

Half

second One On | Two

Off

Locks all buttons on the remote automatically after one minute.

Tap any button then the button(s) you would like to use to send a

command from the remote to your vehicle. If on, LED will flash

blue. When turned off, the LED will flash red twice.

Remote LED Functions and Descriptions

Your remote will communicate to and from your vehicle while in range. The LED will change colors

indicating transmission, confirmation, remote start run time and error confirmations.

Event LED Color LED Duration Chirp(s)

Runtime Remaining:

100 Percent Blue Once every 5 seconds Six times

Runtime Remaining:

66 Percent Purple Once every 5 seconds N/A

Runtime Remaining:

33 Percent Red Once every 5 seconds N/A

All command

confirmations Blue Once or Twice depending on function Once or Twice

depending on

function

All error

confirmations Red Three LED flashes Three chirps

Alarm LED Notifications

In the event that your alarm has been triggered, your remote will receive notifications based on what

zone has been violated. Please see the following table for details and a short description of each

notification. Please note that these notifications are only available with MAX IT and ALARM IT systems.

1 Way Remote Button Functions

Button Duration Additional

Programming

Required Function / Description

Half second no Locks doors and/or arms alarm.

3.5 seconds no Panic/vehicle locater (flashes vehicle’s parking lights and sounds siren and horn).

Half second no Unlocks doors and/or disarms alarm.

Half second no Aux 1. Triggers the auxiliary 1 output (most commonly used for rear defrost or window

roll-down).

2.5 seconds no Trunk release. Triggers the trunk release output and opens the vehicle’s trunk.

Half second no Aux 2. Triggers the auxiliary 2 output (most commonly used for rear defrost or window

roll-down).

2.5 seconds no Activates the remote start. Repeat and remote start will shut off.

Half second no Turns siren chirps on/off (Note: With the siren chirps off, it will still sound in the event the

alarm is triggered).

2.5 seconds no Option programming menu 1 - Installers Only.

Half second no Valet mode (see Valet Mode Section for details)

2.5 seconds no Turns the shock sensor on/off. (Alarm or Alarm/Starter systems only)

Half second yes Drive lock. Activates ignition controlled door locks.

Zone LED Color Chirp(s) Description

Door Trigger(s) Purple and Red Chirps for 30 seconds or until

button tapped on remote One of more of your door trigger

zones have been violated.

Trunk Trigger Purple and Red Chirps for 30 seconds or until

button tapped on remote Your trunk trigger zone has been

violated.

Hood Trigger Purple and Red Chirps for 30 seconds or until

button tapped on remote Your hood trigger zone has been

violated.

Ignition On Trigger Purple and Red Chirps for 30 seconds or until

button tapped on remote Your alarm is triggered when your

vehicle’s ignition is turned on.

DAS Tilt Trigger Purple and Red Chirps for 30 seconds or until

button tapped on remote Your alarm is triggered when your

DAS detects tilt motion

Prewarn Shock Sensor Blue and Red 8 Chirps Your prewarn shock sensor zone

has been violated.

Full Shock Sensor Purple and Red Chirps for 30 seconds or until

button tapped on remote Your full trigger shock sensor zone

has been violated.

2.5 seconds no Option programming menu 2 - Installers Only.

Half second no Activates passive arming (vehicle will arm/lock 30 seconds after the vehicle is disarmed)

Half second yes Activates timer start mode. Timer start mode has multiple programmable settings:

duration settings, temperature settings and self start settings.

Half second yes Activates the built in Turbo Timer function. Additional installation is required when using

this feature on automatic transmission vehicle’s.

2.5 seconds no Car Check / Secure Auxiliary

If you would like additional information on the functionality of your 1 Way companion remote, please visit

the support page at www.compustar.com to download the full user manual.

General System Functions

The remote transmitter functions are predetermined and programmed from the factory. The five button

configuration allows for many functions to be performed through a series of tapping and/or holding

buttons.

Sending Commands

When in range and a command has been sent the remote will beep and unique LED will flash blue or red.

For example, to send a remote start command from the pager, hold the Key/Start button for 2.5

seconds. The remote will beep confirming the command has been sent and that the remote is in range.

Once the vehicle has successfully remote started, the remote will receive a three beep and LED

command indicating the vehicle is running.

Receiving Commands

The remote pager will receive commands indicating the status of the vehicle, confirmation of sending

commands and remote start notifications. For example, after sending the lock command, the pager will

receive LED and chirp signals confirming that the vehicle has been successfully locked/armed. To see if

your pager is in range, tap the button for a half second – if the remote receives an audible and LED

confirmation then it is in range.

Active Lock/Arm and Unlock/Disarm

Tap the Lock button for a half second to lock/arm your vehicle. Tap the Unlock button

to unlock/disarm your vehicle. If equipped this will also activate your starter kill and anti grind

feature. Also you will not be able to start your vehicle with the key until unlock/disarm.

IMPORTANT: If the alarm has been triggered (Siren is sounding, parking lights flashing, and horn

honking), you must wait until the remote pager has been paged before disarming the alarm – the first

button tap will shut off the alarm and the second will unlock/disarm the system.

Passive Lock/Arm

The system can be configured to passively lock and arm the vehicle. Put the system in

passive by tapping the Trunk + Key Start buttons button for a half second.

The remote will beep once and the LEDs will illuminate to indicate the system is in passive lock and

arming mode.

While in passive mode, the system will lock and arm the alarm 30 seconds after the last door is closed.

As an indicator that the vehicle is going to passively lock and arm, the remote and siren will chirp once

and the parking lights will flash once at both 10 and 20 seconds prior to passively locking and arming. If

you want the system to passively arm and not passively lock, ask your local Firstech dealer to turn

Option 1-8 to setting II.

Automatic Transmission Remote Start Function

Hold the Key/Start button for 2.5 seconds to remote start an automatic transmission vehicle. If you

are in range and the vehicle is ready to remote start, the remote will beep once and LED flash blue

indicating that the remote start command has been successfully transmitted.

If you are in range and the remote beeps three times, there is a remote start error. Refer to the “remote

start error diagnostic” on the last page of this manual for details.

Upon receiving confirmation that your vehicle is running, the remote LED will flash the and

remote beep to show the run time. The remote start run time can be programmed for 3, 15, 25,

or 45 minutes - ask your local Firstech dealer to adjust Option 2-7 if you would like a run

time other than 15 minutes (default).

IMPORTANT: Your vehicle’s key must be inserted into the ignition and turned to the “on” position prior

to driving your vehicle. If the foot brake is depressed prior to the key being in the “on” position, the

vehicle will shut off.

Manual Transmission Remote Start Function (Reservation Mode)

In order to remote start a manual transmission vehicle, the system must first be set in Reservation Mode.

Reservation Mode must be set each and every time you want to remote start a manual transmission

vehicle. The purpose of Reservation Mode is to leave the transmission in neutral before exiting the

vehicle.

IMPORANT:

The transmission must be left in the neutral position.

The vehicle’s windows must be rolled up.

The vehicle’s door pins must be in working order.

Do not install this remote start on a manual transmission vehicle that has a convertible or

removable top.

Do not set reservation mode or remote start with people in the vehicle.

Activating Reservation Mode

STEP 1: While the vehicle is running, place the transmission in neutral, set the emergency / parking

brake, and remove pressure from the foot brake.

STEP 2: Remove the key from the vehicle’s ignition. The vehicle’s engine should remain running even

after the key has been removed. If the vehicle does not remain running visit your local authorized

Firstech dealer for service.

STEP 3: Exit the vehicle and close the door. The vehicle’s doors will lock/arm and then engine will shut

down. If the vehicle’s engine does not shut off, your door trigger may be functioning improperly. Do not

use the remote start feature and take your vehicle to a local authorized Firstech dealer for service.

Once the vehicle shuts off your system is in reservation mode and the vehicle is ready to safely remote

start.

IMPORTANT: By default, the system will lock/arm the vehicle upon setting reservation mode. Take care

to not lock your keys inside the vehicle.

Cancelling Reservation Mode

Reservation mode will be cancelled for the following reasons;

You did not activate the parking brake prior to turning off the ignition.

You pressed the foot brake after the key was removed from the ignition.

You released the parking brake after the key was removed from the ignition.

You entered valet mode, opened the vehicle’s door, hood, trunk or set off the alarm.

Reservation Mode Settings

Reservation mode settings can be programmed with Option 1-6. It is recommended that reservation

mode settings are programmed by your local authorized Firstech dealer.

Default 1: Locks doors when Reservation Mode is set.

Option 2: Hold Key/Start button to initiate Reservation Mode

Option 3: Reservation mode sets 10 seconds after the last door is closed, as opposed to immediately.

This option will allow you to access the vehicle’s rear doors, trunk or hatch prior to the system setting

reservation and passively locking/arming.

Option 4: Shuts motor off before locking doors.

Trunk Release

Hold button for 2.5 seconds to release the trunk or hatch. If you are in range, the

remote will beep twice and the LEDs will flash indicating that the trunk release command has

been successfully transmitted. IMPORTANT: Trunk release is an optional vehicle feature that may

require additional parts and labor.

Auxiliary Outputs/Window Roll-Down/Sliding Doors

Your system is equipped with two additional outputs that can be configured to control windows, open

power sliding doors, open a power sliding moon roof, or even turn on a rear defroster. These outputs can

be configured for pulsed, timed or latched settings. Your authorized Firstech dealer can set these outputs

up accordingly. Using auxiliary outputs to control additional vehicle functions will require additional parts

and can be rather labor extensive.

Tap the Function <insert icon> button for a half second followed by the Trunk button to

trigger auxiliary output 1. Tap the Function <insert icon> button for a half second followed by

the Key/Start <insert icon> button to trigger auxiliary output 2. The remote will beep once and parking

lights flash, indicating that the auxiliary output(s) have been triggered.

By default, the system is in secure auxiliary mode, which requires you to tap the Key/Start button

for a half second prior to triggering auxiliary 1 or 2. To turn off secure auxiliary, ask your authorized

Firstech dealer to turn on Option 4-5 to setting II

Silent Arm/Disarm

Upon lock/arm and unlock/disarm, you can eliminate vehicle’s audible confirmation by muting

the siren. Normally, the siren will chirp once to indicate the system is locked/armed and twice to

indicate the system is unlocked/disarmed. To mute the siren tap buttons

Otros manuales para 2W902R-SP

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Antena de otras marcas

Alfa Network

Alfa Network APA-L01 Manual de usuario

Naval

Naval PR-422CA Manual de usuario

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manual de usuario

TERK Technologies

TERK Technologies TV44 Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manual de usuario

HP J8999A Manual de usuario

MobilSat

MobilSat MSP-S Manual de usuario

Steren

Steren ANT-UHF 13 Manual de usuario

Novatel

Novatel 600-G Manual de operación

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manual de usuario

TRENDnet

TRENDnet TEW-AO12O Manual de usuario

Radio Shack

Radio Shack 15-1837 Manual de usuario

CommScope

CommScope CMAX-OMFX-43M-I53 Manual de usuario

Ramsey Electronics

Ramsey Electronics DAP25 Manual de usuario

COBHAM

COBHAM SAILOR 800 VSAT Manual de uso y cuidado

Trango Systems

Trango Systems AD900-9 Manual de usuario

Steren

Steren ANT-100 Manual de usuario

Proxim

Proxim 5054-PA-23 Manual de usuario