First Texas Products GOLD DIGGER Manual de usuario

GOLD DIGGER™

TREASURE

DETECTOR

Owner’s Manual

GOLD DIGGER™

TREASURE DETECTOR

Owner’s Manual

I. ASSEMBLY:

To assemble your GOLD DIGGER™ Treasure

Detector, follow this simple procedure:

1) Unpack your detector and find the following parts:

• Detector Body with armrest, search coil and attached coil knob.

• Upper Stem (thicker silver rod with many holes).

• Lower Stem (thinner silver rod with plastic extension and button).

• Two (2) stem attachment knobs (in the plastic bag).

Searchcoil

Cable

Stem

Attachment

Knobs

Coil Knobs

Upper

Stem

Lower

Stem

Detector

Body

I. ASSEMBLY: (continued)

2) Attach the Upper Stem to the back of the

detector body with the two knobs supplied.

3) Depress the button on the lower stem and

push the lower stem into the upper stem.

4) Wind the search coil cable around the

two-piece stem.

5) Leave some slack in

the cable as you

reach the end of

the lower stem.

6) Attach the coil to

the lower stem using

the attached coil knob.

7) Install two (2) 9-volt

ALKALINE batteries (not

supplied).

There are two battery doors on the

back of the detector body.

IMPORTANT: use 9-volt ALKALINE

batteries ONLY.

Lower

Stem

Searchcoil

Coil Knob

Knurled

Coil Knob

Armrest

Earphone

Jack

Handle

Detector

Body

Button

Upper

Stem

Searchcoil

Cable

Stem

Attachment

Knobs

II. HEIGHT ADJUSTMENT

Stand with the detector in one hand, with the coil on

the ground, a few feet in front of you. If the stem is

not set at a comfortable height, push the button on

the lower rod to change the length. If you make a

large adjustment, wrap the cable again, starting at

the top.

CAUTION: Do not pull on the cable where it

connects to the detector body. It is

permanently attached; too much force

could damage the connection.

III. FIND TREASURE!

Your Treasure Detector will detect all kinds of metal

from iron relics, to coins and household items, to

precious metals like gold and silver.

IV. SENSITIVITY METER

Your meter moves when metal is detected. It shows

the strength of the signal and helps with pinpointing

the object. Watch for the location where the meter

jumps strongly to the right; that’s where the target is.

V. AIR TESTING

You can test your detector by passing coins over the

search coil. Remember that coins found on the

ground will lie flat; so pass the coins parallel to the

search coil for optimum results.

CAUTION: There is metal in the floors, ceilings, wall

and counters of most homes. There is metal in

tables. Keep the detector away from metal.

Do not attempt to place coins on the floor of your

home or apartment; the metal in the floor will

interfere with the signal.

It is best to have a friend hold the detector body, with

the search coil suspended in the air, while you pass

the coins.

If you turn the detector on and turn the Trash

Eliminator switch fully clockwise (to the right), you will

hear different tones. Pass a penny, nickel, dime,

quarter, nail, screwdriver and pull-tab. Notice the

different sounds, or no sound at all! Turn the Trash

Eliminator to many different settings, and sometimes

notice different tones for the same object.

VI. TUNING and GROUND BALANCING

Forget it !

With your GOLD DIGGER™ Treasure Detector, it’s automatic.

Be it hard ground, a sandy beach, rocks, or the black sand

terrains common to gold prospecting locations, your GOLD

DIGGER™ adjusts itself to tune out naturally occurring mineral

deposits, and only detect the metal objects you are looking for.

VII. CONTROLS

•POWER/SENSITIVITY

(the left knob)

The detector is off in the full counter-clockwise position (to the left).

Turn it on with a click to the right. The further clockwise, the higher the

sensitivity. If you get static or noise, then lower the sensitivity a bit.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Detector de metales de First Texas Products

First Texas Products

First Texas Products Gamma 6000 Manual de usuario

First Texas Products

First Texas Products PinPointer Manual de usuario

First Texas Products

First Texas Products Cabelas Platinum Manual de usuario

First Texas Products

First Texas Products VLF 2.1 Manual de usuario

First Texas Products

First Texas Products Teknetics T2 Manual de usuario

First Texas Products

First Texas Products PINPOINTER Manual de usuario

First Texas Products

First Texas Products Platinum Manual de usuario

First Texas Products

First Texas Products Titanium Camo Manual de usuario

First Texas Products

First Texas Products titanumCamo Manual de usuario

First Texas Products

First Texas Products Gold Manual de usuario

First Texas Products

First Texas Products Teknetics T2 Manual de usuario

Manuales populares de Detector de metales de otras marcas

Garrett

Garrett MAGNASCANNER CS 5000 Manual de usuario

Valex

Valex 1800200 Manual de usuario

Gauss

Gauss MIL MD Manual de usuario

Velleman

Velleman CS130 Manual de usuario

Sears

Sears 321.596370 Manual de usuario

Eriez

Eriez X8 Manual de usuario

Steinberg Systems

Steinberg Systems SBS-MD-22 Manual de usuario

Zircon

Zircon MetalliScanner m60c Manual de usuario

nalanda

nalanda MD027 Manual de usuario

REV Ritter

REV Ritter CB-7005 Manual de usuario

Minelab

Minelab F1A4 Manual de usuario

Fisher Research Labs

Fisher Research Labs F70 Manual de usuario

Steinberg Systems

Steinberg Systems SBS-MD-12 Manual de usuario

GOLDEN MASK

GOLDEN MASK 5 Manual de usuario

Grizzly

Grizzly YM 203 Manual de usuario

Fisher Research Labs

Fisher Research Labs 1280-X Aquanaut Manual de usuario

Treasure Cove

Treasure Cove Vibra-Probe 560 Manual de usuario

Accurate Locators

Accurate Locators XL16 IMAGER Manual de usuario