First Power Stinger Manual del propietario

PATENT

PENDING

Owner / Operator’s Manual Rev B.2

Version 1

8941 Dutton Dr,

Twinsburg, Ohio

44087

330-963-2050

Table of Contents

Stinger® Kit Overview

………………………………………………………………………………

Operation Guide

…………………………………………………………………………………….

GoPro® Camera Installation and Usage

……………………………

……………..

Battery Replacement

……………………………………………………………………………..

Replace Transmitter Battery ……………………………………………………

Replace Receiver Batteries ……………………………………………………….

Stinger® Fluid Overview

…………………………………………………………………………

Recommended Maintenance and Safety

…………………………………

…

……

Specifications and Certifications

………………………………………

…………………

Warranty Information

…………………………………………………………………………….

Parts Diagram

…………………………………………………………………………………………..

Stinger® Kit Overview

2 0 1 9 F i r s t P o w e r G r o u p L L C

Stgr

Manual

V1 Rev. B.2

1. Case: The Stinger® Kit comes in a durable and waterproof case.

2. Main Assembly: Non-conductive housing that safely protects the can

from an electric arc and houses the plumbing and valve to route the

Stinger® fluid to the nozzle.

3. Receiver: Allows for remote communication between the main

assembly, Key Fob and the transmitter to turn the dispense on and off.

4. Transmitter: Allows for Stinger® fluid to be sprayed through a press of a

button from a safe location.in the Transmitter and Receiver.

5. Nozzles: The kit comes with a spray nozzle and 2 spare spray nozzles.

These nozzles are used to disperse the Stinger Fluids in a direct stream.

6. GoPro® Camera: Captures live video of where the Stinger fluid is being

sprayed.

7. Smartphone: Used to display video from the GoPro® Camera.

Batteries: Six 9V batteries are provided in addition to the batteries

installed in the Receiver and Transmitter.

Operation Guide

2 0 1 9 F i r s t P o w e r G r o u p L L C

Stgr

Manual

V1 Rev. B.2

Step 1: Take the Main Assembly (2) out the Case (1). Typically, the Receiver (3)

is left in the Main Assembly (2). If the Receiver (3) is not installed, installed it

using the procedure shown on page 16. Begin with screwing a Nozzle (5) into

the threaded insert on the Main Assembly (2). Twist with your hand until the

Nozzle (5) stops turning which is shown in the after images.

Before

After

Operation Guide

Stgr

Manual

V1 Rev. B.2

Step 2: Unscrew the Can Cap on the

bottom of the Main Assembly (2) in the

direction indicated.

Step 3: Fully screw in the threaded top

of the appropriate Stinger® Fluid Can

(1FR™, 2C™,3PAO™) with your hand

until hand tight. It is normal to hear a

pressure release sound before the can

is fully screwed in. Typically, you should

give the can another ½ turn after

hearing the pressure release.

Warnings: If it is hard to screw in the

can, remove the can and try again. DO

NOT FORCIBLY SCREW IN THE CAN. If

the can isn’t fully screwed in, the Can

could leak or

fail inside the Can Housing. The Stinger® can only be used with proprietary

Stinger® fluids, DO NOT attempt to insert other cans into the Stinger®.

Step 4: After installing a can, be sure

to fully screw the orange Can Cap to

the Main Assembly (2) until hand tight.

Can

Cap

Can

Housing

Can

Cap

Operation Guide

Stgr

Manual

V1 Rev. B.2

Step 5: Power on the Receiver (3) in the Main Assembly (2) by flipping the Switch

from the Off Position to On Position.

Step 6: Test fluid stream into a

rag away from equipment for

proper function.

Step 7: Next, power on the Transmitter (4) by flipping the switch from the OFF

position to the ON position. After switching the Transmitter ON, the LED will go

ON for about 1 second, off for about 1 second, and then ON again for about 1

second to indicate it has powered up OK. Wait until the LED has gone through

the flashing process to press the red button. If the LED doesn’t go ON when the

switch is flipped to the ON position, the transmitter may not be functioning.

Warning: Any transmitter will control all powered receivers within range. Make

sure that all other Stingers that are not in use have their receivers and

transmitters turned off.

Switch

Switch in

the OFF

Position

Switch in

the ON

Position

Operation Guide

Stgr

Manual

V1 Rev. B.2

Step 8: Attach the fully assembled

Stinger® to the hot stick using the

yellow universal toothed hot stick

adapter (Hot Stick Adapter). Be sure to

attach the Main Assembly (2) at an

appropriate angle to easily aim stream

of Stinger fluid to the desired location.

We recommend you practice moving

and operating the stinger when the hot

stick is fully extended before using it in

the field.

Step 9: Press the Button on the Transmitter (4) to dispense the liquid. The liquid

will continuously stream out of the Nozzle (5) while the Red button is pressed. If

the LED does not go ON when the button is pressed, the Receiver may be not

functioning.

Hot

Stick

Adapter

Hot

Stick

Switch

LED

Switch in

the ON

Position

Switch in

the OFF

Position

Operation Guide

Stgr

Manual

V1 Rev. B.2

Step 10: Turn the switches on the Receiver (3) and Transmitter (4) to the OFF

position after use (see Steps 5 and 6 to see what each switch position looks like).

Remove the Nozzle (5) from the Main Assembly (2). Place the Transmitter (4),

and Nozzle (5) back in the Case (1).

Step 11: Remove the can cap then, unscrew the can. Make sure the Main

Assembly (2) is upright to prevent the Stinger® fluids from leaking onto your

clothes when the can is unscrewed. Then reinstall the can cap.

Spray

Red

Button

LED

Operation Guide

Stgr

Manual

V1 Rev. B.2

Step 12: Place the Main Assembly (2) with the Receiver (3) into the Case (1) and

close the Case (1). Make sure this manual is in the Case (1) if the Stinger is not in

use.

Can

GoPro® Camera Installation and Usage

2 0 1 9 F i r s t P o w e r G r o u p L L C

Stgr

Manual

V1 Rev. B.2

Step 1: Lift the grey Rubber Locking Plug that is a part of the GoPro® Camera (6)

so that it is touching the back of the camera.

Step 2: To easily slide the

GoPro® Camera (6) into

the Camera Mount on the

Main Assembly (2) shown

on the next page, gently

pinch the black plastic Clip

Ends.

Clip Ends

Rubber

Locking

Plug

Rubber

Locking

Plug

Before

After

This product and/or service is not affiliated with, endorsed by or in any way associated with

GoPro Inc.

or its products and services. GoPro, HERO, Session, Karma and their respective logos are trademarks

or registered trademarks of GoPro, Inc.

Tabla de contenidos

Manuales populares de Herramientas de otras marcas

Martor

Martor SECUNORM 175 Manual de usuario

ERKCO

ERKCO 1000 Manual de usuario

jbc

jbc N4473 Manual de usuario

FEINMETALL

FEINMETALL FZWZ-SET-001 Manual de usuario

Worx Professional

Worx Professional Sonicrafter WU676 Manual de usuario

Gage Bilt

Gage Bilt GB713SH Manual de usuario

Hilti

Hilti DX 9-ENP Manual de usuario

norbar

norbar NORTRONIC 34399 Manual de usuario

BGS technic

BGS technic 8578 Manual de usuario

Makita

Makita DHR241 Manual de usuario

Motor Guard

Motor Guard JMB-1250 Manual de usuario

Power Adhesives

Power Adhesives 805-12 Manual de usuario

Clemco

Clemco 24189 Manual de usuario

VVG

VVG VNG 903 Series Manual de usuario

Hilti

Hilti FX 3-A Manual de usuario

Grizzly

Grizzly H6472 Manual de usuario

axing

axing BWZ 5-02 Manual de usuario

Dh-Robotics

Dh-Robotics RGI-100 Cómo utilizar