First Power Stinger Manual del propietario
PATENT
PENDING
Owner
/ Operator’s
Manual
Rev A.2
Version 2
8941 Dutton Dr,
Twinsburg, Ohio
44087
330-963-2050
Table of Contents
Stinger® Kit Overview
………………………………………………………………………………
1
Operation Guide
…………………………………………………………………………………….
2
GoPro® Camera Installation and Usage
……………………………
……………..
7
Battery Replacement
……………………………………………………………………………..
9
Replace Black Transmitter Batteries ……………………………………………
9
Replace Receiver Batteries ……………………………………………
11
Stinger® Fluid Overview
…………………………………………………………………………
1
5
Recommended Maintenance and Safety
………………………………………….
1
6
Specifications and Certifications
…………………………………
………………………
1
7
Warranty Information
…………………………………………………………………………….
1
7
Parts Diagram
…………………………………………………………………………………………..
1
8
Stinger® Kit Overview
1
|
©20
20
FirstPower Group LLC
Stgr
-
Manual
-
V2 Rev. A.2
1.
Case: The Stinger® Kit comes in a durable and waterproof case.
2. Main Assembly: Non-conductive housing that safely protects the can
and houses the plumbing and valve to route the Stinger® fluid to the
nozzle.
3a.
Receiver: Allows for remote communication between the main
assembly, and the transmitter to turn the dispense on and off.
3b.
Key Fob Transmitters: The Receiver comes with two Key Fob
Transmitters and it exclusively works with those included Key Fob
Transmitters. Each Key Fob Transmitter allows for Stinger® fluid to be
dispensed from a safe location.
4. Nozzles: The kit comes with a dispense nozzle and 2 spare nozzles.
These nozzles are used to dispense the Stinger Fluids in a direct stream.
5. GoPro® Camera: Captures live video of where the Stinger fluid is being
dispensed.
6.
Optional Smartphone: Used to display video from the GoPro® Camera.
7. Batteries: Six 9V batteries are provided in addition to the batteries
installed in the Receiver.
8. Stinger® Manual: This document
4
2
3a
3b
7
5
6
1
Operation Guide
2
|
©20
20
FirstPower Group LLC
Stgr
-
Manual
-
V2 Rev. A.2
Step 1: Take the Main Assembly (2) out of the Case (1). Typically, the Receiver
(3) is left in the Main Assembly (2). If the Receiver (3) is not installed, installed it
using the procedure shown on page 20. Begin with screwing a Nozzle (4) into
the threaded insert on the Main Assembly (2). Twist with your hand until the
Nozzle (4) stops turning which is shown in the after images.
2
4
2
4
2
4
2
4
Before
After
Operation Guide
3
|
©20
20
FirstPower Group LLC
Stgr
-
Manual
-
V2 Rev. A.2
Step 2: Unscrew the Can Cap on the
bottom of the Main Assembly (2) in the
direction indicated.
Step 3: Fully screw in the threaded top
of the appropriate Stinger® Fluid Can
(1FR™, 2C™,3PAO™) with your hand
until hand tight. It is normal to hear a
pressure release sound before the can
is fully screwed in. Typically, you should
give the can another ½ turn after
hearing the pressure release.
Warnings: If it is hard to screw in the
can, remove the can and try again.
DO NOT FORCIBLY SCREW IN THE CAN.
If the can isn’t fully screwed in, the Can could leak or fail inside the Can Housing.
The Stinger® can only be used with proprietary Stinger® fluids, DO NOT attempt
to insert other cans into the Stinger®.
Step 4: After installing a can, be sure to
fully screw the orange Can Cap to the
Main Assembly (2) until hand tight.
2
Can
Cap
2
Can
Housing
Can
2
Can
Cap
Operation Guide
4
|
©20
20
FirstPower Group LLC
Stgr
-
Manual
-
V2 Rev. A.2
Step 5: Power on the Receiver (3a) in the Main Assembly (2) by flipping the
Switch from the Off Position to On Position.
Make sure the power switch is in the
On postion
Step 6: Test fluid stream into a rag
away from equipment for proper
function.
Step 7: Attach the fully assembled
Stinger® to the hot stick using the
yellow universal toothed hot stick
adapter. Be sure to attach the Main
Assembly (2) at an appropriate angle
to easily aim stream of Stinger fluid to
the desired location. We recommend
you practice moving and operating
the stinger when the hot stick is fully
extended before using it in the field.
2
3a
Switch
Hot
Stick
Adapter
Hot
Stick
2
Switch in
the ON
Position
Switch in
the OFF
Position
Operation Guide
5
|
©20
20
FirstPower Group LLC
Stgr
-
Manual
-
V2 Rev. A.2
Step 8: Press the Button on the Transmitter (3b) to dispense the liquid. The
liquid will continuously stream out of the Nozzle (4) while the key fob transmitter
is pressed. If the LED does not go ON when the button is pressed, the batteries in
the button must be replaced. Note: The Transmitter (3b) exclusively connects to
the Receiver (3a) it came with in the Case (1).
Step 9: Turn the switch on the Receiver (3a) to the OFF position after use (see
Steps 6 to see what each switch position looks like). Remove the Nozzle (4) from
the Main Assembly (2). Place the Transmitter (3b) and Nozzle (4) back in the Case
(1).
Step 10: Remove the can cap then,
unscrew the can. Make sure the Main
Assembly (2) is upright to prevent the
Stinger® fluids from leaking onto your
clothes when the can is unscrewed.
Then reinstall the can cap.
4
Spray
Button
LED
3b
2
Can
Operation Guide
6
|
©20
20
FirstPower Group LLC
Stgr
-
Manual
-
V2 Rev. A.2
Step 11: Place the Main Assembly (2) with the Receiver (3a) into the Case (1) and
close the Case (1). Make sure this manual is in the Case (1) if the Stinger is not in
use.
2
1
3a
GoPro® Camera Installation and Usage
7
|
©20
20
FirstPower Group LLC
Stgr
-
Manual
-
V2 Rev. A.2
Note: FirstPower Group LLC does not supply the microSD cards with the camera
Step 1: Lift the grey Rubber Locking Plug that is a part of the GoPro® Camera so
that it is touching the back of the camera as shown below.
Step 2: To easily slide the
GoPro® Camera into (or
out of) the Camera Mount
(shown on the next page),
gently pinch the black
plastic Clip Ends.
This product and
/or service is not affiliated with, endorsed by or in any way associated with GoPro Inc.
or its products and services. GoPro, HERO, Session, Karma and their respective logos are trademarks
or registered trademarks of GoPro, Inc. (See- https://gopro.com/en/us/shop/cameras/hero7-
silver/CHDHC-601-master.html)
Rubber
Locking
Plug
Rubber
Locking
Plug
Before After
GoPro® Camera Installation and Usage
8
|
©20
20
FirstPower Group LLC
Stgr
-
Manual
-
V2 Rev. A.2
Step 3: Slide the GoPro® Camera (5) into the camera mount on the right side of
the Stinger® Main Assembly (2). Make sure that the camera lens is in the same
direction as the nozzle (4).
Step 4: Turn on the GoPro® Camera (5) by
pressing the Power Button shown left. The
camera’s Wi-Fi is turned on automatically.
This product and/or service is not affiliated
with, endorsed by or in any way associated with GoPro Inc.
or its products and services. GoPro, HERO, Session, Karma and their respective logos are trademarks or
registered trademarks of GoPro, Inc. (See- https://gopro.com/en/us/shop/cameras/hero7-
silver/CHDHC-601-master.html) for pairing.
Step 5: After use, gently remove the camera from the Main Assembly (3) and
turn it off. Steps 1-4 for reference. Place the Smartphone (6) and the camera
back into the Case (1)
5
Power
Button
4
5
2
Camera
Mount
4
2
5
Camera
Mount
Before After
Tabla de contenidos
