First International Computer AN11 Manual de usuario

AN11

MAINBOARD

MANUAL

DOC No.: M00B04

Rev. : A0

Date : 11, 2001

Part No. : 25-11607-20

Handling Precautions

Warning:

1. Static electricity may cause damage to the integrated circuits on

the motherboard. Before handling any motherboard outside of its

protective packaging, ensure that there is no static electric charge

in your body.

2. There is a danger of explosion if the battery is incorrectly

replaced. Replace only with the same or an equivalent type

recommended by the manufacturer.

3. Discard used batteries according to the manufacturer’s

instructions.

4. Never run the processor without the heatsink properly and firmly

attached. PERMANENT DAMAGE WILL RESULT!

Observe the following basic precautions when handling the motherboard

or other computer components:

nWear a static wrist strap which fits around your wrist and is

connected to a natural earth ground.

nTouch a grounded or anti-static surface or a metal fixture such as a

water pipe.

nAvoid contacting the components on add-on cards, motherboards,

and modules with the golden fingers connectors plugged into the

expansion slot. It is best to handle system components by their

monting brackets.

The above methods prevent static build-up and cause it to be discharged

properly.

Trademark

All trademarks mentioned in this manual are registered properly of

the respective owners.

Handling Precautions

This manual may not, in whole or in part, be photocopied, reproduced,

transcribed, translated, or transmitted in whatever form without the

written consent of the manufacturer, except for copies retained by the

purchaser for personal archival purposes.

Notice

TableofContents

Table of Contents

Chapter 1 Overview

Package Checklist .......................................................................... 1-2

The AN11 Mainboard ............................................................... 1-3

Main Features ................................................................................ 1-4

FIC Unique Innovation for Users (NOVUS) -

Enhanced Mainboard Features and System Support .................... 1-6

Chapter 2 Installation Procedures

Quick Reference (from Page 2-2 to 2-5) .......................................... 2-2

Mainboard Layout .................................................................... 2-2

1). Clear CMOS, FSB Speed Select,

Auto Detect CPU Core Voltage .................................... 2-3

2). Front Panel Block Cable Connection ............................ 2-5

3). CPU Fan Installation .................................................... 2-5

1). Set System Jumpers/Switches ................................................... 2-5

Clear CMOS: CLR_CMOS ................................................. 2-5

FSB Speed Select: FS ........................................................ 2-6

None Over Clock Enable: JP1_4G ...................................... 2-6

Auto Detect CPU Core Voltage: ADV_EN ......................... 2-7

CPU Core Voltage Setting: ADV ........................................ 2-7

Optional RAID Function Enable: RAID_JP ...................... 2-8

2). Install Memory Modules .......................................................... 2-8

3). Install the CPU .......................................................................... 2-9

4). Install Expansion Cards ............................................................. 2-10

5). Connect Devices ....................................................................... 2-11

Floppy Diskette Drive Connector ..................................... 2-11

IDE Device Connectors ..................................................... 2-12

ATX Power Connectors .................................................... 2-12

Quick Reference (German) G-1

Quick Reference (French) F-1

Quick Reference (Spanish) S-1

Quick Reference (Japanese) J-1

Quick Reference (Chinese) C-1

Quick Reference (Simplified Chinese) |||||||||||||SC-1

AN11MainboardManual

Fan Connectors ................................................................. 2-13

Wake-On-Ring Connector ................................................. 2-13

Wake-On-Lan Connector .................................................. 2-14

Blue Tooth Audio Port Connector .................................... 2-14

CD Audio-In Connectors .................................................. 2-15

Front Panel Block, Power LED and Speaker Connector .... 2-15

PS/2 Keyboard and Mouse Connector ............................. 2-17

Universal Serial Bus Connectors ....................................... 2-17

Printer Connector .............................................................. 2-18

Serial Port Connectors ....................................................... 2-18

Audio I/O Jacks ................................................................ 2-19

Game/MIDI Connector ...................................................... 2-19

Chapter 3 BIOS Setup

CMOS Setup Utility ....................................................................... 3-1

Standard CMOS Setup ................................................................... 3-2

Advanced BIOS Features .............................................................. 3-4

Advanced Chipset Features .......................................................... 3-7

Integrated Peripherals .................................................................... 3-10

Power Management Setup ............................................................. 3-16

PnP/PCI Configurations ................................................................. 3-20

PC Health Status ............................................................................ 3-22

Frequency/Voltage Control ............................................................ 3-23

Load Fail-Safe Defaults .................................................................. 3-23

Load Optimized Defaults ................................................................ 3-24

Supervisor/User Password ............................................................ 3-24

Save and Exit Setup ....................................................................... 3-24

Exit without Saving ........................................................................ 3-24

1 - 1

Overview

Chapter 1

The new Socket-A 1stMainboard®AN11Ôis an ATX sized motherboard

supporting the latest generation of AMD AthlonÔand DuronÔprocessors

at industry leading speeds. By utilizing DDR ( Double Data Rate ) transfer rate

the 100/133 MHz AMD Athlon system bus effectively reaches Front Side Bus

speeds of 200/266 MHz. The board allows 3 PC2100/PC1600 DDR DIMMs for

up to 3 GB of DDR SDRAM.

The AN11 is based around the high performance V-link VIA KT266AÔchipset

comprised of VIA VT 8366A system controller for the North Bridge and the

VIA VT8233Ô for the South Bridge. The AGP 4X functions supported by

KT266A®provides the end-user a photo-realistic 3D experience suitable for

the most robust 3D games and software environments. Onboard AC97 sound,

embedded in VT8233, ensures high quality audio.

The mainboard also comes equipped with the new NOVUS®range of innova-

tive features that assist in the installation and maintenance. The features in-

clude Easy Key, which provides instant keyboard access to the BIOS for

adjustments to Clock and Default settings and LogoGenie, which allows you

to create your own customized logo to be displayed during system boot up.

The BIOS Guardian is an Anti Virus utility that prevents viruses from damag-

ing your system BIOS and rendering your system inoperative.

Expansion is provided by 1 AGP(2X/4X), and 6 PCI slots. In addition, the

1stMainboard AN11 is equipped with 2 dual channeled enhanced PCI bus

master IDE connectors, plus two optional IDE RAID connectors for support-

ing more efficient data backup. Standard I/O connections include 2 serial ports,

1 parallel port, 1 PS/2 mouse and keyboard connector, 4 USB connection ports,

1 IR port, and 1 media connector (Line-In, Line-Out, Mic-In, game port).

1 - 2

AN11MainboardManual

Package Checklist

If you discover any item below was damaged or lost, please contact your

vendor.

þThe mainboard þThis user manual

þOneFDDcable þOne HDD cable

þOneATA/100cable þ Two software CDs (CD Pro, CD Plus)

þOneUSB dual cable

IMPORTANT:AMDCPU HEATSINKINSTALLATION

Be ware finish heat sink install. Before you boot system, please

check the heat sink is complete contact with die of CPU.

The poor contact will bring about over heat, it may damage your

processor.

Itisstrongly recommendedthatat leasta250-watt ATXpowerpupply

be used for this motherboard. Make sure that your ATX power sup-

ply can supply at least 20 amperes on teh +5-Volt lead and 10mA

on the +5-Volt standby lead (+5VSB). Your system may become

unstable / unreliable and may experience difficulty in powering up if

your power supply is inadequate.

NOTE: CD Pro that contains patch files, onboard video/audio chip

drivers, related online help and other useful information can be

found in your mainboard package.

Please install it right after your Windows operating system installa-

tion is done.

Place your CDPro in the drive, an operating menu will

appears in your monitor. Please select

Auto Installation

. It will auto-

matically detect which software tools (patch files, drivers) that the

mainboard needs. Press OK button to go through the whole instal-

lation procedure in a very straight forward and easy way. It also

provides you with a custom way to select wanted patch files and

software drivers that for onboard chips use. The top menu of the

CD Pro lists all the functions that allowed by this board.

1 - 3

Overview

The AN11 Mainboard

1 - 4

AN11MainboardManual

Main Features

nEasy Installation

||BIOS with support for Plug and Play, auto detection of IDE hard drives,

||LS-120|drives, IDE ZIP drives, Windows 98SE, Windows ME, Windows

||NT, Windows 2000, Windows XP, and OS/2.

■Leading Edge Chipset

VIA VT8366A is a single-chip North Bridge for Socket A based Athlon

CPUs with 200/266 MHz Front Side Bus with AGP 4X and PCI plus ad-

vanced memory controller that supports PC1600/PC2100 DDR SDRAM.

VIA VT8233 is a highly Vlink client highly integrated controller that sup-

ports PC99-compliant system. The VT8233 also supports ATA 100 stan-

dard.

■Versatile Main Memory Support

Accepts up to 3 GB DRAM using three DDR DIMMs from 256 MB to 3

GB with support for lightenning-fast (PC1600/PC2100) DDR SDRAM .

■Enhanced PCI Bus Master IDE Controller with Ultra DMA 33/66/100

Support

Integrated Enhanced PCI Bus Master IDE controller features two dual-

channel connectors that up to four Enhanced IDE devices, including CD-

ROM and Tape Backup Drives, as well as Hard Disk Drives supporting

the new Ultra DMA 100 protocol. Standard PIO Mode 3, PIO Mode 4,

DMA Mode 2, DMA Mode 4, UltraDMA-100 Mode 5 devices are also

supported.

■AMD Processors Support

Athlon Socket 462 CPU: 800 MHz to 1.4 GHz and up*at 200 MHz FSB/

1.0 to 1.4 GHz at 266 MHz FSB;

Duron Socket 462: 800 to 950 MHz at 200 MHz FSB.

Athlon XP: 1.5 to 1.9 GHz and up*

Morgen 1 to 1.2 GHz and up*

(*: not tested yet)

1 - 5

Overview

■AGP, ACR, and PCI Expansion Slots

One AGP Bus and one ACR (Advanced Communication Riser) expansion

slot and five PCI Bus expansion slots provided the room to install a full

range of add-on cards.

■Compact Onboard Audio Subsystem

Embeded in VIA VT8233, an integrated high bandwidth Vlink client con-

troller, direct sound AC97 audio subsystem. UltraDMA-66/100 master

mode EIDE controller, six USB controller, ACPI enhanced power manage-

ment, and PC99 compliant.

■■

■Super Multi Input/Output (I/O) Support

Integrated Plug and Play multi-I/O chipset features two high-speed UART

16550 compatible serial ports, one EPP/ECP capable parallel port, one IR

port, one game port, and one FDD connector.

nConvenient Rear Panel USB Connection Support

Two USB ports integrated in the rear I/O panel and two extra USB ports

for either front or rear panel connection allow convenient and high-speed

Plug and Play connections to the growing number of USB compliant

peripheral devices on the market.

■Optional IDE RAID Level 0/1 Support

The optional feature allows this board to back up huge amount data in a

more efficient way.

nOnboard Accelerated Graphics Port (AGP)

The motherboard is installed one 32-bit 1.5V AGP 2X/4X bus with a

dedicated 66MHz/133MHz path from the graphics card to the system

memory offering much greater bandwidth than the 32-bit PCI bus does.

AGP enabled 3D graphics cards can directly access main memory across

this fast path instead of using local memory.

1 - 6

AN11MainboardManual

■■

■BIOS Guardian

BIOS Guardian by default is enabled. It must be disabled in order to

reflash BIOS, thus effectively acts as a fire-wall against viruses that can

attack the BIOS while the system is running.

WARNING: While excute Step3 below, please do not turn off the

sytsem power in order to avoid BIOS damage.

BIOS Guardian can be disabled as follows:

1. Go to BIOS Set Up Menu. (Press Del key while booting.)

2. Go to Advanced BIOS Features Set Up Submenu.

3. Disable BIOS Guardian.

4. Save the setting, and restart system.

FIC Unique Innovation for Users (NOVUS) -

Enhanced Mainboard Features and System Support

■■

■LogoGenie

A user friendly GUI supporting Windows 95/98/98SE (not Windows 2000/

NT/ME), LogoGenie allows you to customize, create or select a Logo

which will be displayed when the system is booting.

NOTE:

1. LogoGenie supports Award BIOS only.

2. If you create a Logo file (.bmp) by LogoGenie, the file size must

||||be 640 x 464 x 256 colors.

To enable this utility, please proceed as follows:

1. Insert CD Pro (version number). Select LogoGenie from the Menu

and follow the installation instructions.

2. After LogoGenie has been installed, go to Windows Start Box.

In Programs Menu, select LogoGenie 2.0, then select LogoGenie.

3. Press F1 to read Help file to understand how to use this software if

it is new to you.

Tabla de contenidos

Otros manuales de Placa madre de First International Computer

First International Computer

First International Computer XTB70 Guía de inicio rápido

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario