FireplaceXtrordinair ProBuilder 72 Linear Manual de usuario

ProBuilder

72 Linear

(MV/GSB2/GSR2)

Installation Manual

WARNING: FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death, or property damage.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Leave the building immediately

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the gas supplier.

HOT GLASS WILL CAUSE

BURNS

DO NOT TOUCH GLASS

UNTIL COOLED

NEVER ALLOW CHILDREN

TO TOUCH GLASS

A barrier designed to reduce the risk of burns from

the hot viewing glass is provided with this appliance

and shall be installed for the protection of children

and other at-risk individuals.

Tested and Listed by

Report # 0028GF105S

Omni-Test Laboratories, Inc.

Portland, Oregon

ANSI Z21.88-2016

CSA 2.33-2016

Built-In Direct Vent

Fireplace

Natural Gas or Propane

Residential or Mobile

Home

This appliance may be installed in an aftermarket, permanently located, manufactured home

(USA only) or mobile home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. A conversion

kit is supplied with the appliance.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

French language manuals at travisindustries.com

Manuels de langue Française à travisindustries.com

Travis Industries, Inc. 12521 Harbour Reach Dr., Mukilteo, WA 98275 www.travisproducts.com

2 Introduction

Overview

This manual details the installation requirements for the Pro Builder 72 Linear mV fireplace. For operating

and maintenance instructions, refer to the Pro Builder 72 Linear mV Owner's Manual.

Listing Details

This appliance was listed by Omni Test Labs to ANSI Z21.88. The listing label is attached to the appliance

near the gas control valve. A copy is shown to the right.

Massachusetts Approval

This manual has been submitted to the Massachusetts Board of State Examiners of Plumbers and Gas Fitters.

Table of Contents 3

Overview ................................................................... 2

Listing Details........................................................... 2

Massachusetts Approval......................................... 2

Installation Options.................................................. 6

Heating Specifications............................................. 6

Dimensions ............................................................... 6

Packing List .............................................................. 7

Additional Items Required....................................... 7

Recommended Installation Procedure................... 7

Massachusetts Requirements ................................ 8

Requirements for the Commonwealth of

Massachusetts.................................................................8

MANUFACTURER REQUIREMENTS.............................8

Fireplace Placement Requirements ....................... 9

Clearances ......................................................................9

Raised Fireplaces............................................................9

Televisions Placed Above the Fireplace................ 10

Minimum Framing Dimensions............................... 11

Min. Framing - Without CoolSmart TV kit ........................11

Min. Framing – With CoolSmart TV Kit............................11

Standoff Assembly................................................... 12

Nailing Brackets ....................................................... 13

Standard vs. Extended Position ............................. 14

Header and Pipe Shield Installation ....................... 15

Corner Installations.................................................. 19

Outdoor fireplace installations ............................... 20

Removing the Front Panel....................................... 21

Gas Line Requirements ........................................... 22

Fuel .................................................................................22

Gas Line Connection .......................................................22

Gas Inlet Pressure...........................................................22

Gas Line Location............................................................23

*Relocating the Gas Line to the Base of Fireplace ......... 23

Electrical Connection............................................... 24

Optional Wall Switch or Thermostat Installation

(GSB and MV only) ................................................... 25

Parallel ConnectionSeries Connection ...................25

Vent Requirements................................................... 26

Vent Clearances ..............................................................26

Vent Firestop or Thimble .................................................26

Altitude Considerations....................................................26

Approved Vent.................................................................26

Vent Installation ...............................................................27

Approved Vent Configurations ............................... 27

Exhaust Restrictor Position..............................................27

Diffuser ............................................................................28

Minimum Vent Configuration .................................. 29

Vent Configuration: Vertical Termination .............. 30

Vent Configuration: Horizontal Termination

with Vertical Rise...................................................... 31

Masonry Chimney Conversions.............................. 32

Class A Chimney Conversion ................................. 33

Termination Requirements...................................... 34

Hearth Requirements ............................................... 35

Facing Requirements............................................... 36

Standard vs. Extended Position ......................................37

Facing Thicker than 1-1/2”............................................38

THICK FACING GUIDE SIZE .........................................38

Screen Assembly Mounts................................................39

Do Not Drill or Screw Zone..............................................40

Mantel Requirements ............................................... 41

Mantel Column Clearances...........................................41

Use of a Non-Combustible Mantel Below Listed

Mantel Clearances .................................................... 42

Finalizing the Installation ........................................ 43

MV Units Only - Pilot Flame Inspection - (see

instructions on page 46) ..................................................43

GSB2 and GSR2 Units Only - Pilot Flame Inspection -

(see instructions on page 46) ..........................................43

Air Shutter Adjustment ....................................................44

Location of Controls ........................................................45

MV Units Only - Starting the Pilot ....................................46

Glass Frame Removal and Installation............................47

Barrier Screen Visual Deflector Adjustment ....................50

Crushed Glass Installation...............................................51

LP Conversion Instructions .................................... 53

Wall Mount Remote Thermostat installation

(optional for GSB2 and MV only) ............................ 58

Packing List .....................................................................58

Installation .......................................................................58

Wiring Diagram – MV Version ................................. 61

Optional Blower Wiring....................................................61

Wiring Diagram – GSB2 Version............................. 62

Wiring Diagram – GSR2 Version............................. 63

CoolSmart TV (Optional) - Installation Overview .. 64

CoolSmart TV - Installation Requirements ......................65

CoolSmart TV - Combustible “Over-Facing” (Optional) ...66

CoolSmart TV - Framing the Chase ................................67

CoolSmart TV - Mantel Clearances .................................68

CoolSmart TV - Fireplace Preparation ............................70

4 Safety Precautions

Safety Warnings

Failure to follow all of the requirements may result in property damage, bodily injury, or even death.

Young children should be carefully supervised when they are in the same room

as the appliance. Toddlers, young children and others may be susceptible to

accidental contact burns. A physical barrier is recommended if there are at risk

individuals in the house. To restrict access to a fireplace or stove, install an

adjustable safety gate to keep toddlers, young children and other at risk

individuals out of the room and away from hot surfaces.

Children and adults should be alerted to the hazards of high surface temperature

and should stay away to avoid burns or clothing ignition. Do not touch the hot

surfaces of the heater. Educate all children of the danger of a high-temperature

heater.

Due to the high temperature, the heater should be located out of traffic and away

from furniture and draperies.

This unit must be installed by a qualified installer to prevent the possibility of an explosion.

This appliance must be installed in accordance with all local codes, if any; if not, in U.S.A. follow ANSI

Z223.1 and NFPA 54(88), in Canada follow CSA B149.1.

A manufactured home (USA only) or mobile home OEM installation must conform with the

Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a

standard is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS

A225.1, or Standard for Gas Equipped Recreational Vehicles and Mobile Housing, CSA Z240.4. This

appliance may be installed in Manufactured Housing only after the home is site located.

All exhaust gases must be vented outside the structure of the living-area. Combustion air is drawn

from outside the living-area structure. The venting must not be connected to a chimney flue serving a

separate solid-fuel burning appliance.

Notify your insurance company before hooking up this fireplace.

The instructions in this manual must be strictly adhered to. Do not use makeshift methods or

compromise in the installation. Improper installation will void the warranty and safety listing.

This heater is approved for use with natural gas (NG) or propane (LP). Burning the incorrect fuel will

void the warranty and safety listing and may cause an extreme safety hazard. Direct questions about

the type of fuel used to your dealer.

Contact your local building officials to obtain a permit and information on any installation restrictions

or inspection requirements in your area.

If the flame becomes sooty, dark orange in color, or extremely tall, do not operate the heater. Call

your dealer and arrange for proper servicing.

It is imperative that control compartments, screens, or circulating air passageways of the heater be

kept clean and free of obstructions. These areas provide the air necessary for safe operation.

Do not operate the heater if it is not operating properly in any fashion or if you are uncertain. Call

your dealer for a full explanation of your heater and what to expect.

Do not store or use gasoline or other flammable liquids in the vicinity of this heater.

Do not operate if any portion of the heater was submerged in water or if any corrosion occurs.

Immediately call a qualified service technician to inspect the appliance and to replace any part of the

control system and any gas control which has been under water.

Safety Precautions 5

Safety Warnings (continued)

Because this heater can be controlled by a thermostat there is a possibility of the heater turning on

and igniting any items placed on or near the appliance.

Light the heater using the built-in igniter. Do not use matches or any other external device to light

your heater.

Never remove, replace, modify or substitute any part of the heater unless instructions are given in this

manual. All other work must be done by a trained technician. Don't modify or replace orifices.

The viewing glass should be opened only for conducting service (or lighting the pilot on millivolt units).

Allow the heater to cool before carrying out any maintenance or cleaning.

Operate the heater according to the instructions included in this manual.

If the main burners do not start correctly turn the gas off and call your dealer for service.

This unit is not for use with solid fuel.

Do not place anything inside the firebox (except the optional artwork).

Warning: Do not operate appliance with the glass front removed, cracked or broken. Replacement

of the glass should be done by a licensed or qualified service person.

Do not throw this manual away. This manual has important operating and maintenance instructions

that you will need at a later time. Always follow the instructions in this manual.

Instruct everyone in the house how to shut gas off to the appliance and at the gas main shutoff valve.

The gas main shutoff valve is usually next to the gas meter or propane tank and requires a wrench to

shut off.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this

appliance and shall be installed for the protection of children and other at-risk individuals.

If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for this

appliance.

Clothing or other flammable material should not be placed on or near the appliance.

Any safety screen, guard, or barrier removed for servicing an appliance must be replaced prior to

operating the appliance.

Installation and repair should be done by a qualified service person. The appliance should be

inspected before use and at least annually by a professional service person. More frequent cleaning

might be required due to excessive lint from carpeting, bedding material, et cetera. It is imperative

that control compartments, burners, and circulating air passageways of the appliance be kept clean.

Travis Industries, Inc. grants no warranty, implied or stated, for the installation or

maintenance of your heater, and assumes no responsibility of any consequential damage(s).

Proposition 65 Warning: Fuels used in gas, woodburning or oil fired appliances, and the products of combustion of such fuels,

contain chemicals known to the State of California to cause cancer, birth defects and other reproductive harm.

California Health & Safety Code Sec. 25249.6

Travis Gas Fireplaces. Stoves and Inserts are protected by one or more of the following patents; U.S. 8,469,021,

7,066,170, 6,602,068, 6,443,726, 6,953,037; Canada 2755517 as well as other U.S. and Foreign Patents pending.

6 Features and Specifications

Installation Options

Residential or Mobile Home

Straight or Corner Placement

Raised or Floor Placement

Internal or External Chase

Bedroom Approved

Heating Specifications

Natural Gas Propane

72 ProBuilder Approximate Heating Capacity (in square feet)* Up to 2,250 Up to 2,250

Maximum BTU Input Per Hour 45,000 45,000

* Heating capacity will vary with floor plan, insulation, and outside temperature.

Dimensions

4-7/8"

124mm

77-1/8" *

1959mm *

275 lbs.

125 Kg.

15-7/8" *

404mm *

43"

1092mm

Left

a' gauche

Front

avant

Right

droit

Rear

arrie're

* Includes the required 1/2" clearance to each side and rear of the fireplace.

20-1/2"

521mm

75-3/4" 1924mm

1-1/2"

38mm

3-3/4"

96mm

31"

788mm

9-3/4"

248mm

SIDE OF

FIREPLACE

Installation (for qualified installers only) 7

Packing List

LP (Propane) Conversion Kit - Burner Orifices (2)-(#54), Pilot Orifice (0.14 LP), LP Regulator

Thimble (2-Piece Assembly)

Pipe Shield, Header Shield (shipped attached to top of fireplace)

Wall Switch, Cover Plate, and Wire (GSB2 and MV Only)

GreenSmart Remote Control (GSR2 Only)

Additional Items Required

Gas Line Equipment (shutoff valve, pipe, etc.)

Electrical Equipment (min. 14 gauge, grounded line)

This Fireplace Requires 8 lbs. (3.6 Kg) of 1/4” Crushed Glass

94500580 Platinum (10 lbs./4.55Kg)

94500581 Bronze (10 lbs./4.55Kg)

94500582 Cobalt (10 lbs./4.55Kg)

94500583 Black (10 lbs./4.55Kg)

Recommended Installation Procedure

Frame the opening for the fireplace. Make sure to allow for vent installation.

Install the vent, gas line and electrical hook-up.

Install the drywall.

Install the hearth (if applicable).

Install the facing (if applicable).

Install the mantel (if applicable).

Finalize the installation (see page 41).

8 Installation (for qualified installers only)

Massachusetts Requirements

NOTE: The following requirements reference various Massachusetts and national codes not contained in this document.

Requirements for the Commonwealth of Massachusetts

For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in

part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent

termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and

porches, the following requirements shall be satisfied:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gasfitter shall

observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the floor level where the

gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery operated or hard

wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served

by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the

services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired

carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.

In the event that the requirements of this subdivision cannot be met at the time of completion of installation, the owner shall

have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day

period, a battery operated carbon monoxide detector with an alarm shall be installed.

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be

ANSI/UL 2034 listed and IAS certified.

Signage

A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight

(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or

equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW. KEEP

CLEAR OF ALL OBSTRUCTIONS”.

Inspection

The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation

unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the

provisions of 248 CMR 5.08(2)(a)1 through 4.

Exemptions

The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:

• The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54

as adopted by the Board; and

• Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the

dwelling, building or structure used in whole or in part for residential purposes.

MANUFACTURER REQUIREMENTS

Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or

venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment

and the venting system shall include:

• Detailed instructions for the installation of the venting system design or the venting system components; and

• A complete parts list for the venting system design or venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for

venting the flue gases, but identifies “special venting systems”, the following requirements shall be satisfied by the manufacturer:

• The referenced “special venting system” instructions shall be included with the appliance or equipment installation

instructions; and

• The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list

and detailed installation instructions.

A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting

instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or

equipment at the completion of the installation.

See Gas Connection section for additional Commonwealth of Massachusetts requirements.

Installation (for qualified installers only) 9

Fireplace Placement Requirements

Fireplace must be installed on a level surface capable of supporting the fireplace and vent

Fireplace must be placed directly on wood or non-combustible surface (not on linoleum or carpet)

Fireplace should be located out of traffic and away from furniture and avoid burns.

Fireplace must be placed so the gaps below and above the glass frame do not become blocked.

Fireplace may be placed in a bedroom. Please be aware of the large amount of heat this appliance produces

when determining a location.

Clearances

(a) Clearance to Side of Fireplace 1/2” (13mm). Do not place insulation in this space.

NOTE: Drywall (or other combustible) may contact the first ½” of the sides of the fireplace.

(b) Clearance to Back of Fireplace 1/2” (13mm). Do not place insulation in this space.

standoffs.

Raised Fireplaces

The fireplace (and hearth, if desired) may be placed on a platform designed to support the fireplace and vent.

The base of the fireplace must be a minimum 60” (1524mm) below the room ceiling.

The top of the control door (firebox opening) is approximately 8-3/4” (223mm) above the base of

the fireplace. For a typical raised fireplace of 36” (915mm), place the fireplace on a platform 27-

1/4” (693mm) tall.

10 Installation (for qualified installers only)

Televisions Placed Above the Fireplace

The following section gives guidelines to place a television above the fireplace.

IMPORTANT NOTE REGARDING TELEVISIONS AND THIS FIREPLACE

Most television manufacturers instruct the homeowner not to place the television above a heat source like this fireplace. Doing

so may decrease the longevity of the television and negate the warranty. If you do place a television above the fireplace, you

should place a mantel (or build-out) between the fireplace and television (or use a CoolSmart TV Wall™ kit). Follow the

guidelines below to reduce the amount of heat reaching the television. Travis Industries does not take responsibility for any

negative impact to televisions placed near this fireplace.

Minimum Dimensions:

(a) Minimum Mantel Height above Base of Fireplace* 39” (991mm) with 4” (102mm) mantel depth

(b) Minimum Mantel Depth* 4” (102mm)*

(Measured to the side of fireplace ZC-can)

* Minimum mantel depth must be 4”(102mm) to allow heat to dissipate. If using a mantel larger than 4”(102mm),

make sure to adjust the mantel height (a) to meet the mantel clearancer (see mantel requirements on page 41 for

details).

The mantel must extend 2” in front of the television and 1” to both sides.

If you have a television that is greater than 6” deep (including the 1” gap behind), you will need to alter the mantel depth

and height (see the example below).

The television must have a 1” gap to the wall to allow for proper cooling. Any build-out near the television must

maintain a 3” gap to the top and sides to prevent heat from being trapped near the television.

NOTE: The mantel must extend 1”(26mm) in front of the TV and 1”(26mm) to both sides. If you have a TV that is greater than

3” (77mm) deep (including the 1”(26mm) gap behind), you will need to alter the mantel depth and height.

Fireplace

Min. 1" (26mm)

Min. 1" (152mm) Min. 2" (51mm)

Optional Column

or Build-Out



Min. 1" (26mm) Air Gap Behind TV

Min. 3"

(77mm)

Television (TV)



IDB01243

(b) Depth

(a)

Height

Above

Base of

Fireplace

0" (0mm)

1" (25mm)

2" (51mm)

8" (203mm)

7" (178mm)

6" (152mm)

5" (127mm)

4" (102mm)

3" (76mm)

9" (229mm)

10" (254mm)

11" (279mm)

12" (305mm)

45" (1143mm)

44" (1118mm)

43" (1093mm)

IDB01242

PB42,54,72

42" (1067mm)

41" (1042mm)

40" (1016mm)

39" (991mm)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Chimenea de interior de FireplaceXtrordinair

FireplaceXtrordinair

FireplaceXtrordinair 4237 Manual de usuario

FireplaceXtrordinair

FireplaceXtrordinair 864 TV 40K CleanFace Manual de usuario

FireplaceXtrordinair

FireplaceXtrordinair 44 DV XXL EF Manual de usuario

FireplaceXtrordinair

FireplaceXtrordinair 42 Apex Clean Face Manual de usuario

FireplaceXtrordinair

FireplaceXtrordinair 1924E Manual de usuario

FireplaceXtrordinair

FireplaceXtrordinair 98501021 FPL ELECTRIC 51 Manual de usuario

FireplaceXtrordinair

FireplaceXtrordinair ProBuilder 42 CleanFace Manual de usuario

FireplaceXtrordinair

FireplaceXtrordinair 564 Arched Face Manual de usuario

FireplaceXtrordinair

FireplaceXtrordinair 4237 Manual de usuario

FireplaceXtrordinair

FireplaceXtrordinair 36 ELITE-ZC Manual de usuario

FireplaceXtrordinair

FireplaceXtrordinair Elite Fireplacextrodin 36-Elite Manual de usuario

FireplaceXtrordinair

FireplaceXtrordinair 36 DV-XL (Direct Vent Extra Large) Manual de usuario

FireplaceXtrordinair

FireplaceXtrordinair 36 DV EFIII Manual de usuario

FireplaceXtrordinair

FireplaceXtrordinair 864 See-Thru Manual de usuario

FireplaceXtrordinair

FireplaceXtrordinair 36A-BI Manual de usuario

FireplaceXtrordinair

FireplaceXtrordinair 864 TRV 31K Manual de usuario

FireplaceXtrordinair

FireplaceXtrordinair ProBuilder 36 CleanFace MV Manual de usuario

FireplaceXtrordinair

FireplaceXtrordinair ProBuilder 42 Linear Manual de usuario

FireplaceXtrordinair

FireplaceXtrordinair 564 Series Manual de usuario

FireplaceXtrordinair

FireplaceXtrordinair 36A-ZC Manual de usuario

FireplaceXtrordinair

FireplaceXtrordinair 864 TV 40K CleanFace Manual de usuario

FireplaceXtrordinair

FireplaceXtrordinair 4415 HO GSR2 Manual de usuario

FireplaceXtrordinair

FireplaceXtrordinair 98500507 Manual de usuario

FireplaceXtrordinair

FireplaceXtrordinair 1080 Manual de usuario

Manuales populares de Chimenea de interior de otras marcas

Brigantia

Brigantia 35-DVRS31N-2 Manual del propietario

Nordpeis

Nordpeis Bergen Manual de usuario

Superior

Superior BCT2536TMN Manual de usuario

Quadra-Fire

Quadra-Fire 5100I-GD-B Manual de usuario

Renaissance

Renaissance RUMFORD 1000 Manual de usuario

Lacunza

Lacunza IV-800 Manual de usuario

Baxi

Baxi 940 Instrucciones de uso

Dru

Dru Maestro 60/2 Tall RCH Manual de usuario

Diamond Fireglass

Diamond Fireglass SS-O22 Manual de usuario

HearthStone

HearthStone Windsor Bay 8830 Manual de programación

Napoleon

Napoleon ASCENT B42 Manual de usuario

Enviro

Enviro E33GI Manual de usuario

Smeg

Smeg L30 FABE Instrucciones de montaje

KEDDY

KEDDY K700 Manual de usuario

Godin

Godin 3451 Manual de usuario

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manual de usuario

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manual de usuario

Desa

Desa CCFPDFT Manual de operación