Field Controls 46330800 Manual de usuario

COMBUSTION AIR SYSTEM

Model: CAS-2WM

WEIL-MCLAIN OUTSIDE AIR KIT

FOR USE WITH OIL BURNER MODELS QB-180 & QB-300

The Air Boot™ model CAS-2WM is for use only on the designated burner(s) as

described in these instructions only when the specific burner includes this Air Boot™

when shipped from the burner manufacturer or where the burner instructions

specifically reference the model CAS-2WM Air Boot™ as an optional air intake

system.

ITEMS INCLUDED IN KIT:INSTALLER SUPPLIED ITEMS:

1 -Air Boot™ Air Duct Pipe and Elbows as needed

1 -4” VRV (Vacuum Relief Valve) -use 4” Dryer Venter, Aluminum or

1 -4” IAH Hood Galvanized Steel

1 -Set of Gaskets ¼” NPT 90° street ell for oil line if needed

1 -Burner Coupling Set Exterior rated caulk, silicone sealant or

2 -Mounting Bolts equivalent

4” IAH HOOD

AIR BOOT™

4” VRV

Page 2

THE PURPOSE OF THE VACUUM RELIEF VALVE (VRV)

The vacuum relief valve provides combustion air to the burner

if the outside air supply is interrupted for any reason. Typical

situations would be blockage of the air intake or duct, or wind

effect which cause a negative pressure at the air intake hood.

VRV OPERATION

With normal air flow through the air intake hood and duct, the

VRV stays closed. All combustion air comes in through the air

duct. If the pressure in the Air Boot™ drops, the valve door

opens. Room air flows in through the VRV to provide the air

needed for combustion. When the Air Boot™ pressure returns

to normal, the VRV closes.

WARNING: This symbol is used in these instructions

to indicate presence of hazards, which can cause

severe personal injury, death or substantial property

damage.

WARNING: Failure to perform the following can cause

severe personal injury, death or substantial property

damage:

•Read all instructions before starting

•Follow all instructions in proper order

•Turn off service switch on boiler and any other

electrical disconnect switches

•Turn off the fuel supply valve(s) and disconnect fuel lines from the

burner

INSTALLATION

1. Rotate the burner oil solenoid valve as shown in Figure 1, steps A-D. Do

not reconnect the oil line (per E-F). The solenoid valve must be aligned as

shown to prevent interference with the Air Boot™.

2. Remove the two ¼” bolts holding the oil pump to the burner housing.

Remove the oil pump.

3. Remove the screw which holds the air band to the housing. Remove the

air band.

4. Install the sealing gaskets onto the burner housing (See Figure 2).

5. Install mounting spacer onto Air Boot™ (See Figure 3).

6. Place the Air Boot™ on the housing, through the large opening in the back

side of the Air Boot™ (See Figure 3). Press the Air Boot™ into position

and align roughly plumb with the burner. Align the Air Boot™ mounting

holes with the burner oil pump mounting holes.

NOTE: Replace pump coupling with the coupling supplied with kit.

7. Now put the oil pump and the AirBoot™ kit coupling back into place.

Replace the two ¼” oil pump mounting screws. Tighten the screws.

8. Reconnect the burner oil line to the ell fitting on the oil pump per Figure 1,

drawings E and F.

Figure 1

Rotate Oil Solenoid valve and realign 90° fitting as

shown below. Do not reconnect the oil line as in E

and F until you have installed the Air Boot™

Figure 2

Figure 3

Figure 4

Page 3

9. Mount the VRV tee assembly or 90° elbow onto the Air Boot™ intake.

Fasten using three (3) sheet metal screws on all joints (See Figure 5).

10. Assemble the VRV balance weight onto the gate. Screw the weight all the

way in. Then attach lock nut and knurl nut (See Figure 6).

11. Mount the VRV assembly onto the tee and fasten with the supplied screw

and nut in collar tabs. To ensure proper operation, Check the gate for

being level across the pivot points and plumb (See Figure 7).

12. Refer to Figure 8 for general installation layout.

AIR DUCT AND AIR INTAKE HOOD (See Figure 8)

1. Mount the air intake hood through an outside wall. It must be at least 12”

(inches) ABOVE grade or snow line.

2. Locate the air intake hood at least 3’ (feet) BELOW (or 6 feet horizontally

from) any appliance VENT termination.

3. When the appliance is sidewall vented, locate the air intake hood on the

same side of the building as the appliance vent outlet.

4. Always mount the air hood with the intake pointed down.

5. To install the air intake hood, cut a 4 ¼” hole through the side of the

building. Slide the hood through the wall and fasten with appropriate

screws.

6. Seal around the exterior plate with an exterior rated caulk, silicone sealant

or equivalent.

7. Locate the air hood so the air piping length doesn’t exceed the limits

below:

Number of Elbows Maximum Length

of Air Pipe

2 to 4 35 Feet

528 Feet

621 Feet

714 Feet

8. Construct the air duct piping with 4” diameter dryer vent or aluminum or

galvanized steel pipe, using as few elbows as possible.

9. Fasten and support the air duct piping to prevent damage and separation

of joints.

Figure 7

Figure 6

Figure 5

Figure 8

Page 4

ADJUSTMENTS

AIR INTAKE BOOT AIR SETTING

1. Follow the instructions in the Boiler and Burner Installation Manuals for adjusting and setting the burner.

WARNING: Failure to properly adjust the burner after installing this kit can result in severe personal injury, death or

substantial property damage.

2. Loosen the air band screw on the Air Boot™. Position the screw at the initial setting on the following page. Use this

setting only as a starting point. Do not leave the burner with this setting unless your testing proves it to be acceptable.

INITIAL AIR BOOT™ AIR CONTROL SETTINGS

Input Range (GPH) Air Band Setting

0.55 –0.70 25°

0.75 -1.00 60°

1.10 -1.75 80°

2.00 -2.55 180°

3. Start the burner and adjust the air control as needed to achieve the required CO2 and smoke levels. Set over fire

draft to appliance manufacturers’ specifications (typically -.02” of water). Secure air control knob with indicator

bracket. If draft levels are not obtainable or controllable, use standard industry methods to control the draft or call the

Field Controls Tech Line at 1-800-742-8368 for more information.

4. Adjust the counterweight on the vacuum relief valve so the gate remains closed during the burner setup and testing.

VACUUM RELIEF VALVE COUNTERWEIGHT

1. After you have completed adjusting the burner, adjust the VRV counterweight.

2. With the burner running normally, rotate the counterweight screw counterclockwise until the gate just begins to open.

3. Check the combustion again to verify no changes have occurred. If OK, hold the counterweight screw in position and

tighten the hex nut against the gate to lock the screw permanently in position.

P/N 46330800 Rev D 11/00

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Admirador de Field Controls

Field Controls

Field Controls 206900 Manual de usuario

Field Controls

Field Controls VentCool 1.8 Manual de usuario

Field Controls

Field Controls PVE-100 Manual de usuario

Field Controls

Field Controls CAC-120 Manual de usuario

Field Controls

Field Controls 46263300 Manual de usuario

Field Controls

Field Controls 46229000 Manual de usuario

Field Controls

Field Controls 46311800 Manual de usuario

Field Controls

Field Controls 46483500 Manual de usuario

Field Controls

Field Controls 46202200 Manual de usuario

Field Controls

Field Controls SWG Stainless Series Manual de usuario

Field Controls

Field Controls 46139100 Manual de usuario

Field Controls

Field Controls 46261700 Guía

Field Controls

Field Controls 46263500 Guía de inicio rápido

Field Controls

Field Controls PVG-100 Manual de usuario

Field Controls

Field Controls CAS-4 Manual de usuario

Field Controls

Field Controls 46385600 Manual de usuario

Field Controls

Field Controls 46256400 Manual de usuario

Field Controls

Field Controls FAPV180-AC Manual de usuario

Field Controls

Field Controls 46334200 Manual de usuario

Field Controls

Field Controls VentCool Tahoe Series Manual de usuario

Field Controls

Field Controls ventCool Manual de usuario

Field Controls

Field Controls 46255400 Manual de usuario

Field Controls

Field Controls Eliminator Manual de usuario

Field Controls

Field Controls 1575700 Manual de usuario

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje