FGM TC 155 GTI Manual de usuario

TABLE OF CONTENTS

INTERNATIONAL SYMBOLS 1

SAFETY RULES 2

ASSEMBLY 4

OPERATION 9

MAINTENANCE 16

ADJUSTMENTS 21

WIRING ` 27

TROUBLESHOOTING GUIDE 29

STORAGE 31

TECHNICAL SPECIFICATIONS 32

Read this manual carefully so that you will know how to assemble, use and maintain this unit, Fill in and mail

the registration card provided with the unit. For service other than described in this manual, contact an

authorized service dealer. He will provide you with parts and service.

NOTE: This lawn tractor is equipped with a combustion engine, which should not be used near any land covered

with grass or brush, unless the engine's exhaust system is equipped with a spark arrester meeting local laws.

The operator should maintain the spark arrester in effective working order.

INTERNATIONAL SYMBOLS

These symbols appear on your unit and in the supplied documentation.

You should learn and understand their meaning.

SAFETY RULES

THESE INSTRUCTIONS ARE FOR YOUR PROTECTION. YOU SHOULD READ THEM CAREFULLY

WARNING: THIS LAWN TRACTOR IS ABLE TO CUT HANDS, FEET AND THROW OBJECTS. IF YOU DO

NOT FOLLOW THE SAFETY INSTRUCTIONS, YOU COULD EXPERIENCE SERIOUS INJURIES.

1. GENERAL OPERATION: 2. SLOPE OPERATION:

*KNOW CONTROLS AND HOW TO STOP QUICKLY. SLOPES ARE A MAJOR FACTOR RELATED TO LOSS OF CONTROL

*READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS AND TIP OVER ACCIDENTS, WHICH CAN RESULT IN SEVERE

IN THE AND ON THE MACHINE BEFORE STARTING. INJURY OR DEATH. ALL SLOPES REQUIRE EXTRA CAUTION.

*ONLY ALLOW RESPONSIBLE ADULTS, WHO ARE FAMILIAR IF YOU CAN NOT BACK UP THE SLOPE OR IF YOU FEEL UNEASY

WITH INSTRUCTIONS TO OPERATE THE MACHINE. ON IT, DO NOT MOW IT.

*WEAR SAFETY GLASSES OR EYE SHIELDS WHEN DO !

ASSEMBLING OR OPERATING THE MACHINE *MOW UP AND DOWN, NOT ACROSS

*DO NOT OPERATE MACHINE WHEN BAREFOOT. ALWAYS *REMOVE OBSTACLES SUCH AS ROCKS, TREE LIMBS, ETC.

WEAR SUBSTANTIAL FOOTWEAR, PREFERABLY STEEL TOED SHOES. *WATCH FOR HOLES, RUTS OR BUMPS. UNEVEN TERRIAN COULD

*DO NOT WEAR LOOSE FITTING CLOTHING THAT COULD OVERTURN THE MACHINE. TALL GRASS CAN HIDE OBSTACLES.

GET CAUGHT IN MOVING PARTS. *USE SLOW SPEED. CHOOSE A LOW GEAR SO THAT YOU WILL NOT HAVE

*CLEAR THE AREA SUCH AS ROCKS, TOYS, WIRES, ETC., TO STOP OR SHIFT WHILE ON SLOPE.

WHICH COULD BE PICKED UP AND THROWN BY BLADES. *FOLLOW THE MANUFACTURER'S RECOMMENDATIONS FOR WHEEL

*BE SURE THE AREA IS CLEAR OF PEOPLE WHEN MOWING. WEIGHTS OR COUNTERWEIGHTS TO IMPROVE STABILITY.

*STOP MACHINE IF ANYONE ENTERS THE AREA. *USE EXTRA CARE WITH GRASS COLLECTOR OR OTHER ATTACHMENTS.

*NEVER CARRY PASSENGERS. THIS CAN CHANGE THE STABILITY OF THE MACHINE.

*DO NOT MOW IN REVERSE UNLESS NECESSARY. *KEEP ALL MOVEMENTS ON THE SLOPE SLOW AND GRADUAL.

*ALWAYS LOOK DOWN AND BEHIND BEFORE AND *DO NOT MAKE SUDDEN CHANGES IN DIRECTION OR SPEED.

DURING BACKING UP. *AVOIC STARTING OR STOPPING ON A SLOPE. IF TIRES LOSE TRACTION

*BE AWARE OF MOWER DISCHARGE AND DO NOT POINT TURN OFF THE BLADES AND PROCEED SLOWLY DOWN THE SLOPE.

IT AT ANYONE.

*DO NOT OPERATE MOWER WITHOUT THE ENTIRE GRASS DO NOT !

COLLECTOR. *DO NOT TURN ON SLOPES UNLESS NECESSARY, AND THEN

*SLOW DOWN BEFORE TURNING. SLOWLY AND GRADUALLY DOWNHILL, IF POSSIBLE.

*NEVER LEAVE A RUNNING MACHINE UNATTENDED *DO NOT MOW NEAR DROP-OFF DITCHES OR EMBANKMENTS

ALWAYS TURN OFF BLADES, SET PARKING, STOP ENGINE THE MOWER COULD SUDDENLY TURN OVER IF A WHEEL IS

*AND REMOVE KEYS BEFORE DISMOUNTING. OVER THE EDGE OF A CLIFF OR DITCH, OR IF AN EDGE

*TURN OFF BLADES WHEN NOT MOWING. CAVES IN.

*STOP ENGINE BEFORE REMOVING GRASS COLLECTOR. *DO NOT MOW ON WET GRASS. REDUCED TRACTION COULD

*MOW ONLY IN DAYLIGHT OR GOOD ARTIFICIAL LIGHT. CAUSE SLIDING.

*DO NOT OPERATE THE MACHINE WHILE UNDER THE *DO NOT TRY TO STABILIZE THE MACHINE BY PUTTING YOUR

INFLUENCE OF ALCOHOL OR DRUGS. FOOT ON THE GROUND.

*WATCH FOR TRAFFIC WHEN OPERATING NEAR OR

WHILE CROSSING ROADWAYS.

*USE CARE WHEN MOVING AROUND A FIXED OBJECT

TO PREVENT THE BLADES FROM STRIKING IT. NEVER

DELIBERATELY RUN OVER ANY FOREIGN OBJECT.

*USE EXTRA CARE WHEN LOADING OR UNLOADING

THE MACHINE INTO A TRAILER OR TRUCK.

*USE CARE WHEN PULLING LOADS OR USING HEAVY

EQUIPMENT.

aUSE ONLY APPROVED DRAWBAR HITCH POINTS.

bLIMIT LOADS TO THOSE THAT YOU CAN SAFELY CONTROL

cDO NOT RUN SHARPLY. USE CARE WHEN BACKING.

dUSE COUNTERWEIGHTS, WHEEL WIEIGHT WHEN SUGGESTED

IN ATTACHMNENTS INSTRUCTIONS.

THIS SYMBOL MEANS THAT IMPORTANT SAFETY PRECAUTIONS HAVE TO

POINTED

OUT

YOUR

SAFETY

INVOLVED

SAFETY RULES

3. CHILDREN: 4. SERVICE:

TRAGIC ACCIDENTS CAN OCCUR IF THE OPERATOR IS NOT *USE EXTRA CARE IN HANDLING GASOLINE AND OTHER FUELS.

ALERT TO THE PRESENCE OF CHILDREN. CHILDREN ARE aUSE ONLY AN APPROVED CONTAINER.

OFTEN ATTRACTED TO THE MACHINE AND THE MOWING bNEVER REMOVE GAS CAP OR ADD FUEL WITH THE ENGINE RUNNING.

ACTIVITY. NEVER ASSUME THAT CHILDREN WILL REMAIN cNEVER REFUEL THE MACHINE INDOORS.

WHERE YOU LAST SAW THEM. dNEVER STORE THE MACHINE OR FUEL CONTAINER INSIDE WHERE THERE

*KEEP CHILDREN OUT OF THE MOWING REA AND UNDER IS OPEN FLAME, SUCH AS IN A WATER HEATER.

WATCHFUL CARE OF ANOTHER RESPONSIBLE ADULT. *CHECK FUEL SUPPLY BEFORE EACH USE ALLOWING SPACE FOR EXPANSION

*BE ALERT AND TURN MACHINE OFF IF CHILDREN ENTER AREA. AS THE HEAT OF THE ENGINE AND SUN CAN CAUSE GASOLINE TO EXPAND

*BEFORE AND WHEN BACKING, LOOK DOWN AND BEHIND FOR CHILDREN. AND OVERFLOW THE TANK.

*NEVER CARRY CHILDREN. THEY MAY FALL OFF AND BE SERIOUSLY *USE EXTRA CARE WHEN HANDLING BATTERY ACID. ACID CONTACT WITH

INJURED OR INTERFERE WITH SAFE MACHINE OPERATION. SKIN MAY CAUSE SEVERE BURNS. EYE CONTACT MAY CAUSE BLINDNESS.

*NEVER ALLOW CHILDREN TO OPERATE THE MACHINE. *USE EXTRA CARE WHEN SERVICING THE BATTERY. EXPLOSIVE GAS IS

*USE EXTRA CARE WHEN APPROACHING BLIND CORNERS, SHRUBS, PRODUCED IN THE BATTERY. DO NOT SERVICE THE BATTERY WHILE

TREES OR OTHER OBJECTS THAT MAY OBSCURE VISION. SMOKING OR NEAR AN OPEN FLAME. THIS MAY CAUSE THE BATTERY

TO EXPLODE CAUSING SERIOUS INJURY.

*NEVER RUN A MACHINE INSIDE A CLOSED AREA. EXHAUST FUMES CONTAIN

CARBON MONOXIDE, AND ODOURLESS AND DEADLY GAS.

*KEEP NUTS AND BOLTS, ESPECIALLY BLADE ATTACHMENT BOLTS, TIGHT

AND KEEP EQUIPMENT IN GOOD CONDITION.

*NEVER TAMPER WITH SAFETY DEVICES. CHECK OPERATION REGULARLY.

*DO NOT CHANGE THE ENGINE GOVERNOR SETTINGS OR OVERSPREAD

ENGINE.

*REDUCE FIRE HAZARDS. KEEP MACHINE FREE OF GRASS , LEAVES OR

OTHER DEBRIS BUILD-UP. CLEAN UP OIL OR FUEL SPILLAGE. ALLOW

MACHINE TO COOL BEFORE STORING.

*STOP AND INSPECT THE EQUIPMENT IF YOU STRIKE AN OBJECT. REPAIR IT,

IF NECESSARY, BEFORE RESTARTING.

*NEVER MAKE ADJUSTMENTS OR REPAIRS WITH THE ENGINE RUNNING.

*GRASS COLLECTOR COMPONENTS ARE SUBJECTS TO WEAR, DAMAGE AND

DETERIORATION, WHICH COULD EXPOSE MOVING PARTS OR ALLOW OBJECTS

TO BE THROWN. FREQUENTLY CHECK COMPONENTS AND REPLACE WITH

MANUFACTURER'S RECOMMENDED SPARE PARTS. WHEN NECESSARY.

*MOWER BLADES ARE SHARP AND CAN CUT. WRAP THE BLADES OR WEAR

GLOVES, AND USE EXTRA CAUTION WHEN SERVICING THEM.

*CHECK BRAKE OPERATING FREQUENTLY. ADJUST AND SERVICE AS NEEDED.

ASSEMBLY

UNPACKING STEERING WHEEL (Fig. 2)

The tractor is not completely assembled at

the factory, for transportation reasons.

After removing the packaging, check the

machine for any damage during the shipment,

locate the hardware bag and loose parts. Take

care while removing the machine from the pallet,

to avoid any damage on the mower deck.

STANDARD PACKIN

*tractor

*steering wheel

*seat with fasteners

*battery Fig. 2

*grass catcher

*trailer hitch - optional Proceed to the following steps:

*bag with owner's manual ,engine manual, 2 keys 1. Straighten the front wheels.

for ignition, 1 decal with an arrow. 2. Align the holes of the steering wheel (pos. 1) with the

*hardware bag for grass catcher the hole in the steering shaft (pos. 2).The steering

wheel bar closest to the operator's seat has to be

IDENTIFICATION aligned with the lengthwise axis of the tractor.This

orientation of the steering wheel makes all the

The tractor identification plate is located control elements located on the dash panel

under the driver's seat and behind the easily visible.

battery. Make a note of the serial number 3. Insert the lock pin (pos. 3) through the holes,

on this page. This serial number will have and drive it throught the holes with a

to be quoted when contacting your hammer.

distributor for service and ordering spare

parts for the tractor. See Fig. 1. SEAT (Fig. 3)

Serial No ...............................................

Fig. 3

Proceed to the following steps:

1. Discard the plastic cover from the seat

2. Take off both the adjustment knobs

and both hex flange bolts.

Fig. 1: Identification plate 3. Place the seat and tighten securely with

two bolts, flat and spring washers.

4. Connect the safety switch (Fig. 3).

ASSEMBLY

TRAILER HITCH (Fig. 4) The grass collector has been partially assembled.

To final assemble it correctly (to fit the

collector cover with tractor fenders), it is

recommended to follow the instructions below:

1. Take all parts of grass collector out from paper box

including the partially assembled collector.

2. Lay the assembly down on level surface facing down

the plastic collector cover (pos. 28). Make sure

not scratching plastic collector cover from outside.

3. Open the front frame assembly (pos. 8) to align holes

on the top frame assembly (pos. 26). Insert bolts

(pos. 22) and tight the nuts (pos. 3).

Fig. 4

4. Using bolt (pos. 14) and nut (pos. 3) tighten the front

Note: If your tractor is equipped with the optional frame assembly on the bottom frame assembly.

trailer hitch then proceed to the following steps:

5. Insert corner support (pos. 10) and (pos. 15) between

1. Place trailer hitch in place. top frame assembly (pos. 18) to fit on outside part

2. Install supplied bolts, washers and nuts. Tighten of tubes. Tighten them by bolts (pos. 14) and nuts

securely. (pos. 3). Be careful about the right placement

of corner supports.

GRASS COLLECTOR BAG (Fig. 5

)

6. Tilt down the braces (pos. 20).

7. Place the connecting brace (pos. 16) on the outside

of the bag (pos. 9) and tighten it together with braces

(pos. 20) using bolts (pos. 17) and nuts (pos. 3).

8. Insert the dumping lever (pos. 7) through the hole

of the collector cover (pos. 28) and secure it with

the screw (pos. 29). Recommendation: to make

the assembling easier you can make the thread

into the dumping lever by using the screw (pos. 29)

before inserting dumping lever (pos.7) through

collector cover (pos. 28).

9. Check out the tightness of grass collector bag (pos. 9)

and placing of washer (pos. 11) and (pos. 13) on right

places and tighten well nuts (pos. 3).

10. Use the plastic extrusions of collector bag (pos. 9)

on the side and bottom part of front frame assembly

(pos. 8).

Fig. 5

ASSEMBLY

PLACING THE GRASS COLLECTO

ON THE TRACTOR (Fig. 6)

Fig. 7

Fig. 6

Proceed to the following steps: WARNING

1. Lift the grass collector assembly with This tractor is equipped with a safety

both hands. Slant it to an angle of micro-switch and the cutting system will

approximately 40 degrees (Fig. 6). not function when the grass collector

assembly is not in place. Do not tamper

2. Slide the grass catcher on the two with this microswitch.

support brackets located on the rear collector

plate of the tractor. Check out the alignment

of grass collector cover to the fender. In case PREPARATION BEFORE THE FIRST OPERATION

it is not fitting precisely adjust the position

of grass collector using the movement The tractor is shipped without gas

of the braces on the slots or by light bending for safety reasons.Check oil level.

of the braces. Fill fuel tank with reccommended gas.

3. When the grass catcher is properly

positioned, place the decal with the DANGER

triangle symbol directly opposite to the

symbol on the rear of the tractor. This Lead acid batteries generate explosive

will assist alignment in the future (Fig. 7). gases. Keep sparks, flame and smoking

materials away from batteries. Always wear

eye protection when around batteries.

ASSEMBLY

BATTERY PREPARATIO

Maintenance-free battery is delivered dry (without electrolyte).

The electrolyte is delivered in two bottles together with

machine. The battery is placed under the seat. Thanks to

its cover it is waterproof and up angle 45° it is sealed

against leakage, so the electrolyte do not leak under

standard usage.

CHARGE BATTER

1. Loose wire battery holder.

2. Disconnect black electric wire (“-“pole).

3. Disconnect red electric wire (“+“pole). Fig. 8

4. Take the battery out of the tractor.

DANGE

5. Take off covers from top of the battery.

Electrolyte is a dangerous acid and

6. Slowly fill the electrolyte into each battery cell until poisonous. Always wear eye protection

it is full up to lower end of tube. Protect your skin when handling acid or battery

7. Connect 12 volt battery charger to the battery. POISON/DANGER-CAUSES SEVERE

Charge the battery with 2 amps for 4 hours. Do not BURNS

overcharge the battery. Disconnect battery charger

when the battery is fully charged and close battery Contains sulfuric acid.

cells with covers. Avoid contact with skin, eyes or clothing

To prevent accidents, neutralize excess acid

8. Put the battery back to the tractor and connect it to with baking soda and rinse empty container with water

electric wires – first to the red one and then to

the black one.

NTIDOT

9. Cover the poles with rubber cover. EXTERNAL: Flush with water

INTERNAL: drink large quantities of water or milk.

10. Fasten the battery with wire battery holder. Follow with milk of magnesia, beaten

eggs or vegetable oil.

CALL A PHYSICIAN IMMEDIATELY

EYES: Flush with water for 15 minutes and

get prompt medical attention.

KEEP OUT OF THE REACH OF CHILDREN

TO SERVICE THE ENGINE

NOTE: The engine is shipped with oil!

If oil needs to be added or changed then fill crankcase with

SAE 10w-30 oil. (See engine Operation Manual).

Do not overfill or it will cause serious damage

to the engine.

Before starting the engine, read carefully

the engine manual.

ASSEMBLY

GAS FILLING DANGE

Use extra care in handling fuels. They are

flammable, vapors are explosive. Allow the

engine to cool down before refuelling. Do

not smoke. Use safety approved container

only to store your gasoline!

In the engine owner's manual, you will find fuel and

oil recommendations.

TYRES

Proceed to the following steps:

Fig. 9

1. Check the tyre pressure :

(1.0 BAR) for the front wheels: 100 kPa

Use only regular unleaded gasoline. (0.8 BAR) for the rear wheels. 80 kPa

The recommended lowest octane level is 95.

If the engine runs on gasoline with a lower 2. Adjust pressure up or down if necessary (Fig.10).

octane level than 95, an effect known as

knocking can arise. This engine temperature NOTE: The tyre pressure is important for

occurs when reached operating level and can an even cut.

cause engine failure.

REFUELLING

WARNING

Make sure there is good air ventilation

when refuelling.

1. Stop the engine and let it cool down.

2. Open the gasoline cap slowly in order to

release any possible high pressure.

3. Tighten the gasoline cap carefully after refuelling. Fig. 10

4. Dry fuel tank around the area of the gasoline cap.

Clean the tank regularly. Impurities in the tank

can cause operating problems.

For refuelling, use an approved container with

funnel. Do not overfill the tank, which contains

approximately 8 litres.

OPERATION

CONTROLS (Fig. 11) OPERATION AND DESCRIPTION

1. Dash panel Toggle switch cutting system (Fig.11, pos.5).

2. Throttle control lever (15.5HP & 16HP) To engage, push the mower system down on the rocker

or throttle control knob (18HP) switch and place it in the ON position: this actuates

3. Choke control (only 18HP) the cutting system clutch which drives the blades.

4. Ignition switch

5. ON/OFF switch cutting system When the collector is full with grass the overload

6. Service hour meter (only 16HP & 18HP) protection switch located inside the grass collector

7. DC AMMETER (only 16HP & 18HP) will be mechanically activated and the warning buzzer

8. Engine oil pressure light (only 20HP Honda) will come on. The buzzer is located in the

9. Steering wheel center of the dash panel.

10. Cutting height adjustment lever

11. Forward speed pedal Note:

12. Reverse speed pedal It is highly recommended that when the warning

13. Parking brake lever buzzer is activated to disengage the mower system

14. Brake pedal to prevent the tunnel from being severely clogged.

15. Transmission disengagement lever

Fig. 11b

Fig. 11a

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cortacésped de FGM

FGM

FGM STM60-318 Manual de usuario

Manuales populares de Cortacésped de otras marcas

RHINO

RHINO 1958 Manual de usuario

Wolf Garten

Wolf Garten Compact plus 40 B Manual de usuario

Cub Cadet

Cub Cadet LTX 1045 Manual de usuario

Craftsman

Craftsman 917.378461 Manual de usuario

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manual de usuario

Challenge

Challenge CH18V2 Instrucciones de operación

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manual de usuario

DEWEZE

DEWEZE ATM-725 Manual de operación

Weed Eater

Weed Eater 180083 Manual de usuario

Husqvarna

Husqvarna Poulan Pro PP185A42 Manual de usuario

Better Outdoor Products

Better Outdoor Products Quick Series Manual de usuario

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manual de funcionamiento

MTD

MTD 795, 792, 791, 790 Manual de usuario

Toro

Toro Groundsmaster 3505-D Manual de usuario

Dennis

Dennis FT 610 Manual de usuario

AIRFORCE

AIRFORCE F-15 Gen 3 Manual de usuario

MTD

MTD 126-220-000 Manual de usuario

Toro

Toro 74806 Manual de usuario