Fervi 0657 Manual de usuario

USE AND

MAINTENANCE MANUAL

Bench lathe

Art. 0657

TRANSLATION OF THE ORIGINAL INSTRUCTIONS

fervi.com

MACHINES AND

ACCESSORIES

Page 2 of 69

All rights are reserved of reproduction and dissemination of this Technical Manual and documentation cited and/or attached. It is expressly forbidden to reproduce, publish or distribute any information from this Manual. Copyright by FERVI

FOREWORD

Read this manual before any operation

ORIGINAL INSTRUCTIONS

Before starting any operation it is compulsory to read this instruction manual. The guarantee

that the machine will function and perform properly is strictly dependent upon the application

of all the instructions contained in this manual.

Operator Qualification

The operators assigned to using this machine must be supplied with all of the necessary

information and instruction and should be provided with adequate training regarding

safety in pertaining to:

a) The conditions of use of the equipment;

b) Foreseeable abnormal situations, pursuant to Article 73 of Legislative Decree

81/08.

We guarantee the Machine's conformity to the specifications and technical instructions

described in the Manual on the date of issuance and listed herein; On the other hand,

the machine may also be subject to important technical changes in the future, without

the manual being updated.

Therefore, see FERVI for information about modifications that could be implemented.

REV. 3

February 2014

fervi.com

MACHINES AND

ACCESSORIES

Page 3 of 69

CONTENTS

1INTRODUCTION ........................................................................................5

1.1 Preface..........................................................................................................................6

2SAFETY WARNINGS ..................................................................................7

2.1 General safety rules for machine tools..........................................................................7

2.2 Special safety rules for lathes .......................................................................................9

2.3 Safety rules for electrical machine equipment ..............................................................9

2.4 Technical support........................................................................................................10

2.5 Other provisions .........................................................................................................10

3TECHNICAL SPECIFICATIONS ................................................................. 11

4DESCRIPTION OF THE MACHINE ............................................................. 13

4.1 Intended use and field of application ..........................................................................13

4.2 Description of the main parts......................................................................................14

4.2.1 Supporting table...................................................................................................... 14

4.2.2 Head and spindle ..................................................................................................... 15

4.2.3 Spindle speed change............................................................................................... 15

4.2.4 Automatic feed setting.............................................................................................. 16

4.2.5 Tool holder slide and carriage.................................................................................... 16

4.2.6 Tailstock................................................................................................................. 17

4.3 Identification plate .....................................................................................................17

4.4 Pictograms..................................................................................................................18

5SAFETY DEVICES ON THE MACHINE ........................................................ 20

5.1 Electrical safety devices..............................................................................................20

5.2 "Mechanical" Safety Devices .......................................................................................21

5.2.1 Protective screens.................................................................................................... 21

5.3 Personal Protective Equipment (PPE) .........................................................................23

6FORBIDDEN USES AND HAZARDS ........................................................... 24

7LIFTING, TRANSPORTATION AND STORAGE ........................................... 26

7.1 Lifting .........................................................................................................................26

7.2 Transportation ............................................................................................................27

7.3 Warehouse storage .....................................................................................................27

8ASSEMBLY AND COMMISSIONING .......................................................... 28

8.1 Identification of the installation site ...........................................................................28

8.2 Support base...............................................................................................................28

8.3 Levelling the machine .................................................................................................28

8.3.1 Preliminary phase .................................................................................................... 28

8.3.2 Transverse levelling of the table ................................................................................ 29

8.3.3 Levelling the lathe guide rails .................................................................................... 29

fervi.com

MACHINES AND

ACCESSORIES

Page 4 of 69

8.4 Operations before starting the machine......................................................................29

8.4.1 Cleaning the machine............................................................................................... 29

8.4.2 Lubrication and greasing........................................................................................... 29

8.4.3 Connection to the power supply network..................................................................... 29

8.4.4 Open circuit test ...................................................................................................... 30

9DESCRIPTION OF CONTROLS .................................................................. 31

9.1 Control buttons ...........................................................................................................31

9.1.1 Control panel buttons and pilot lamps......................................................................... 31

9.2 HAND WHEELS AND CONTROL LEVERS ........................................................................32

9.2.1 Hand wheels for the carriage and tool holder slides ...................................................... 32

9.2.2 Automatic feed activation lever.................................................................................. 33

9.2.3 Tailstock lever and handwheel................................................................................... 34

10 OPERATION.......................................................................................... 35

10.1 Traditional turning ...................................................................................................36

10.2 Milling ......................................................................................................................38

10.3 How to set the spindle speed ...................................................................................40

10.4 How to set up the automatic feed of the carriage ....................................................41

11 MAINTENANCE ..................................................................................... 46

11.1 Lubrication...............................................................................................................46

11.2 Periodic checks ........................................................................................................49

11.3 Adjusting the Machine .............................................................................................49

11.3.1 Adjusting the tension of the belts............................................................................... 49

11.3.2 Tailstock alignment .................................................................................................. 49

11.3.3 Adjusting the play of the slides.................................................................................. 50

12 DISPOSAL OF PARTS AND MATERIALS .................................................51

13 ELECTRICAL SYSTEM ............................................................................ 52

14 TROUBLESHOOTING ............................................................................. 53

15 ACCESSORIES AND SPARE PARTS ........................................................ 54

fervi.com

MACHINES AND

ACCESSORIES

Page 5 of 69

1INTRODUCTION

This manual is delivered with the machine, and it must be regarded as an inseparable part of

it.

The manufacturer holds all ownership to material and intellectual property of this manual;

any disclosure or copying, even partial, of this publication without prior written consent is

forbidden.

The purpose of this manual is to provide the knowledge necessary for the use and

maintenance of the Bench lathe Art. 0657 and create a sense of responsibility and

knowledge of the possibilities and limits of the device entrusted to the operator.

As the machine is entrusted to experienced and skilled operators, the following machine must

be perfectly known by the operator if it is to be used safely and effectively.

Operators must be properly trained and prepared, so make sure that this manual is read and

consulted by the staff responsible for commissioning, operation and maintenance of the

Bench lathe. This is to make all operations the safest and most effective possible for those

who carry out these tasks.

Therefore, it is imperative to strictly comply with the requirements in this manual, a

necessary condition for safe and satisfactory operation of the machine.

Prior to installation and use of the Bench lathe, authorised personnel must:

carefully read this technical document;

know which protections and safety devices are available on the machine, their location

and how they work.

The buyer is responsible for ensuring that users are properly trained, that they are aware of

all the information and instructions in this document and that they are aware of the potential

risks of operating the Bench lathe.

The manufacturer waives any and all responsibility for damage to people and/or

things caused by non-observance of the instructions in this manual.

The Bench lathe has been designed and built with mechanical guards and safety devices

designed to protect the operator/user from possible injury. It is strictly forbidden to modify or

remove guards, safety devices and caution labels. If this must be done (for example, for

cleaning or repair), make sure that no one can use the machine.

Modifications to the machine carried out by the user must be considered their sole

responsibility, therefore the manufacturer waives any and all responsibility for any

damage caused to persons and/or property resulting from maintenance performed

by unqualified personnel and in a manner unlike the operating procedures shown

below.

fervi.com

MACHINES AND

ACCESSORIES

Page 6 of 69

GRAPHIC REPRESENTATION OF SAFETY,OPERATIONAL AND RISK WARNINGS

The following boxes are designed to attract the attention of the reader / user for the proper

and safe use of the machine:

Pay attention

This highlights behavioural rules to prevent damage to the machine and/or the occurrence of

dangerous situations.

Residual Risks

This highlights the presence of dangers that cause residual risks to which the operator must

pay attention in order to avoid injury or damage to property.

1.1 Preface

For safe and easy operation of the Bench lathe, this manual must be read carefully in order to

acquire the necessary knowledge. In other words, durability and performance are strictly

dependent on how it is used.

Even if already familiar with the Bench lathe, it is necessary to follow the instructions

contained herein, in addition to the general precautions to be observed while working.

Acquire full knowledge of the machine.

Read this manual carefully to understand: operation, safety devices and all necessary

precautions. All this is to allow safe use of the machine.

Wear appropriate clothing for the job.

The operator must wear appropriate clothing, so as to prevent the occurrence of

unpleasant accidents.

Maintain the machine with care.

Using the machine

The machine must only be used by qualified personnel trained to use the machine by

authorized personnel.

fervi.com

MACHINES AND

ACCESSORIES

Page 7 of 69

2SAFETY WARNINGS

2.1 General safety rules for machine tools

Risks associated with the use of the machine

Do NOT underestimate the risks related to the use of the machine and stay focused on the

work you are carrying out.

Risks associated with the use of the machine

Despite the implementation of all safety devices for safe use of the machine, it is necessary to

take note of all the accident prevention requirements highlighted in various parts of this

manual.

Risks associated with the use of the machine

Every person who is responsible for the use and maintenance of the machine should first have

read the instruction manual, particularly the chapter dealing with safety.

It is recommended that the plant safety manager get written confirmation of the above.

Risks associated with the use of the machine

During all work phases with the machine, you should proceed with great caution in

order to avoid damage to persons, to property or to the machine itself.

Please only use the machine for its envisaged uses.

Do not tamper with the safety devices provided by the manufacturer.

Risks associated with the use of the machine

Before starting any work on the machine, the operator must wear the appropriate personal

protective equipment (PPE) such as gloves and eye protection.

1. Always check the efficiency and integrity of the machine.

2. Before connecting the machine to the mains make sure that the switch is in the rest

position.

3. Do not start the machine in an enclosed or poorly ventilated area, or in the presence of

a flammable and/or explosive atmosphere. Do not use the machine in damp and/or wet

locations, or those exposed to rain or humidity.

fervi.com

MACHINES AND

ACCESSORIES

Page 8 of 69

4. Avoid starting accidentally.

5. Before starting the machine, get used to ensuring that no remaining adjustment or

maintenance wrenches have remained inserted.

6. Keep the workplace tidy and free from hindrances; disorder causes accidents.

7. Make sure that the work environment is forbidden to children, non-employees and

animals.

8. Do not perform tasks on the machine other than those for which it was designed. Only

use the machine in the manner in which it was intended, as described in this instruction

manual.

9. Work without disturbances.

10.Work areas must be well lit.

11.Always wear eye protection and protective gloves while working. If dust is produced,

use the appropriate masks.

12.Wear appropriate clothing. Loose clothing, dangling jewellery, long hair, etc.., can get

caught in the moving parts, causing irreparable injury.

13.Replace worn and/or damaged parts, check that the guards and protection devices work

properly before operating. If necessary, have the machine checked by the service

support personnel. Use only original spare parts.

14.Cut the mains voltage supply to the machine when:

the machine is not being operated;

is left unattended;

you are performing maintenance or adjustment because the machine does not

work properly;

the power cable is damaged;

you are replacing its tool;

in case the machine is being moved to another location;

you are cleaning the machine.

15.Do not use the machine in areas with a risk of fire and/or explosion.

16.It is recommended that users of this publication, for maintenance and repair, have a

basic knowledge of mechanical principles and of repair technique procedures.

17.The person responsible for company safety is to make sure that the staff

responsible for using the machine have read and understood this manual in its

entirety.

18.The company safety manager is responsible for monitoring the company's risk

status according to Legislative Decree no. 81/08.

fervi.com

MACHINES AND

ACCESSORIES

Page 9 of 69

2.2 Special safety rules for lathes

1. Firmly secure the workpiece before starting the lathe, using the jaws installed on the

spindle.

2. Always use the tool in an appropriate manner. Perform only the work for which the tool

is made. Do not use the tool for inadequate work.

3. Only use suitable resistance tools in relation to the work that is to be done. This is to

avoid risky and unnecessary overloading for the operator, which may be harmful for

the life of the tools themselves.

4. Do not pick up moving tools or other moving parts. To stop the moving parts on the

machine, always only use the stop command device.

5. Before performing any measurement of the workpiece mounted on the spindle, turn the

motor off, unplug it and wait for the spindle to stop.

6. Do not remove the shavings with your hands, even at a standstill. To do this, use tongs

or a palette knife.

7. When the work tools need to be replaced or the speed needs to be changed, stop the

motor, unplug it and wait for the spindle to stop.

8. Do not leave the machine until the equipment and other moveable parts are completely

stopped.

9. After the work is completed, clean the tool and check its efficiency.

2.3 Safety rules for electrical machine equipment

Risks associated with the use of the machine

1. Do not modify the electrical system in any way. Any attempt in this regard may

jeopardize the operation of electrical devices, thus causing malfunction or accident.

2. Work carried out in the electrical system of the machine must, therefore, be carried out

only by qualified and authorized personnel.

3. If one hears unusual noises, or feels something strange, immediately stop the machine.

Then carry out an inspection and, if necessary, perform any repairs as required.

1. Ensure supply voltage complies with the label and technical specifications (230 V / 50

Hz).

2. It is necessary to use a device for the automatic interruption of the power supply in

case of failure, which is to be coordinated with the machine's electrical system. For

more detailed information, contact a trusted electrician.

3. The mains power outlet should be bipolar grounded (10/16 A, 250 V), extension cables

must have sections that are the same or greater than the sections of the power cable

of the machine.

4. The power supply cable (and its possible extension cable) should never come in contact

with hot objects, sharp edges, wet or oiled surfaces.

fervi.com

MACHINES AND

ACCESSORIES

Page 10 of 69

5. The power cord should be checked regularly and before each use to check for signs of

damage or wear. If these are not in good condition, replace the cable.

6. Do not use the power cord to lift the machine or to remove the plug from the socket.

2.4 Technical support

For any problems or concerns, please contact, without hesitation the Customer Service

Department of your dealer, who has competent and specialized staff, specific equipment and

spare parts.

2.5 Other provisions

IT IS FORBIDDEN TO TAMPER WITH SAFETY DEVICES

The first thing to do when starting work is to check for the presence and integrity of the

protections and the operation of the safety devices.

If any defect is encountered do not use the machine!

Even more so, it is strictly forbidden to modify or remove guards, safety devices,

labels and indication signs.

fervi.com

Tabla de contenidos

Otros manuales de Torno de Fervi

Fervi

Fervi T999/230V Manual de usuario

Manuales populares de Torno de otras marcas

Kval

Kval 990-H Manual de usuario

Holzmann

Holzmann VD 1100ECO Manual de usuario

Grizzly

Grizzly G0632 Guía de inicio rápido

Grizzly

Grizzly G0462 Manual de usuario

Grizzly

Grizzly G0709 Manual de usuario

HAMAR LASER

HAMAR LASER L-700 Suplemento

Promac

Promac 941VA Manual de usuario

Grizzly

Grizzly G0949G Manual de usuario

Teknatool

Teknatool Nova Mercury Manual de usuario

Traub

Traub TNL12.2 Manual de usuario

WoodFast

WoodFast M305 Manual de usuario

Milltronics

Milltronics ML Series Manual

Milltronics

Milltronics SL6 Series Manual

OmniTurn

OmniTurn GT-75 Manual de usuario

Axminster

Axminster CQ6230A-2/910 Manual de usuario

Jet

Jet JWL-1640EVS Manual de servicio

Grizzly

Grizzly G4000 Manual de usuario

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN ED1000FB Manual de usuario