FERREX MM4115A Manual de usuario

PRODUCED IN CHINA FOR:

GB IE

Great care has gone into the manufacture of this product and it should

therefore provide you with years of good service when used properly. In

the event of product failure within its intended use over the course of the

first 3 years after date of purchase, we will remedy the problem as quickly

as possible once it has been brought to our attention. In the unlikely event

of such an occurrence, or if you require any information about the product,

please contact us via our helpline support services, details of which are to be

found both in this manual and on the product itself.

ALDI STORES LTD. PO BOX 26, ATHERSTONE

WARWICKSHIRE, CV9 2SH

ALDI STORES (IRELAND) LTD.

PO BOX 726, NAAS, CO. KILDARE

Visit us at www.aldi.com

AFTER SALES SUPPORT 805501

GB IE

[email protected]

MODEL:

MM4115A 07/2021

+44(0) 1904727501 +353(0) 19022605

YEAR

WARRANTY

User Manual

BELT AND DISC SANDER

Original User Manual

Overview

2345

67 8 9

10 11 12 13

14 15 16

18 19

21 20

Overview

Scope of delivery/device components

Belt and Disc Sander

45° Mitre gauge

Worktable rod

Rubber foot (x4)

Cord wrap (x2)

Big ﬂat washer M5 (x12)

Screw M5x16 (x4)

Base plate

Nut M5 (x4)

Screw M5x12 (x4)

Disc guard

Screw M4 x 14

Flat washer M4 (x2)

Worktable assembly

Spanner 10x13 mm

Hex key 3, 4, 6 mm (3 pcs)

Operating manual and warranty card

(not depicted)

Device components

Sanding disc

Work support

Sanding belt

Carrying-handle

Lower belt cover

ON /OFF switch

Disc Dust outlet

Table lock knob

Bevel gauge

Worktable

Belt Dust outlet

Belt tension lever

Tracking knob

Required tools (not included)

Phillips screwdriver

PH1

Spanner size 8 mm

Scope of delivery/device components

Table of content

Overview..................................................................................................................2

Scope of delivery/device components...................................................................4

General information................................................................................................6

Reading and storing the operating manual..................................................................6

Intended use...................................................................................................................... 6

Explanation of symbols..................................................................................................... 7

Safety.......................................................................................................................8

General safety notes for power tools.............................................................................. 8

Check the device and scope of delivery................................................................14

Assembly instruction............................................................................................. 15

Attaching rubber feet to base plate...............................................................................15

Mounting the base plate................................................................................................. 16

Attaching the cord wrap..................................................................................................16

Attaching the disc guard................................................................................................. 17

Attaching worktable to sanding disc.............................................................................17

Attaching worktable to belt sander...............................................................................18

Before ﬁrst use...................................................................................................... 20

Operation...............................................................................................................20

Turning the device on and off.........................................................................................21

Chamfering........................................................................................................................21

Mitre sanding....................................................................................................................22

Sanding ﬂat surfaces....................................................................................................... 23

Sanding curved surfaces................................................................................................ 24

Cleaning................................................................................................................. 24

Maintenance.......................................................................................................... 25

Replacing the sanding belt............................................................................................ 25

Adjusting belt tracking....................................................................................................26

Testing....................................................................................................................27

Storage...................................................................................................................27

Transport............................................................................................................... 28

Load securing for transport............................................................................................28

Troubleshooting.................................................................................................... 28

Technical data........................................................................................................29

Noise/vibration information...........................................................................................29

Declaration of conformity......................................................................................31

Disposal..................................................................................................................32

Table of content

General information

Reading and storing the operating manual

This operating manual is part of the belt and disc sander (hereinafter also

called "device"). It contains important information on how to set up and

use the device.

Before using the device, read the operating manual carefully, in particular

the safety instructions. Failure to follow this operating manual may lead to severe

injuries or product damage.

This user manual is based on the standards and regulations that are valid within the

European Union. Outside the EU, please also note the country-speciﬁc directives and

laws.

Keep this operating manual for future reference. If you pass this device on to a third

party, you must also supply this operating manual.

Intended use

The device is designed for sanding wood of all types, as well as materials that are

similar to wood. It is only suitable for workpieces small enough to fully rest on the

respective worktable. Working on larger workpieces requires additional supports not

included with the device.

The device is suitable for use in non-condensing and non-explosive atmospheres.

This device is intended for private use only and is not suitable for commercial use.

Use the device only as described in this operating manual. Any other use is improper

and may lead to product damage or even personal injury. This device is not a toy.

The manufacturer or retailer assume no liability for damage caused by improper or

incorrect use.

Residual risks

Despite proper use, hidden residual risks cannot be completely excluded.

Depending on the type of device, the following risks may occur:

- Health risks which may result from vibration emissions if the device is used for a

long period of time or is not properly used or maintained.

- Injuries and material damage, which are caused by the moving blade or

breaking tool heads.

- Health risks may result from working with toxic or hazardous materials (eg.

asbestos) or if appropriate personal protection, due to hazardous material use, is

not applied.

General information

Explanation of symbols

The following symbols and signal words are used in this user manual, on the device

or on the packaging.

This symbol provides you with useful additional information on

handling and use.

Declaration of conformity (see chapter “Declaration of conformity”):

Products marked with this symbol meet all the applicable Community

regulations of the European Economic Area.

Wear hearing protection.

Wear protective goggles.

Wear a dust mask.

General information

Safety

The following signal words are used in this operating manual.

WARNING! This signal symbol/word denotes a

hazard with an average risk level that

could lead to death or severe injury if

it is not avoided.

CAUTION! This signal symbol/word denotes a

hazard with a low risk level that could

lead to mild or moderate injury if it is

not avoided.

NOTE! This signal word provides a warning

about potential material damage.

General safety notes for power tools

WARNING!

Read all safety notes, instructions, illustrations and technical

data provided with this power tool. Failure to follow the

instructions below may result in electric shock, ﬁre and/or

serious injury.

Keep all safety notes and instructions for future reference.

The term "power tool" used in the safety notes refers to both

mains-operated power tools (with power cord) and battery-

powered power tools (without power cord).

Workplace safety

-Keep your work area tidy and well lit.

Clutter or unlit work

areas can lead to accidents.

-Do not operate power tools in explosive atmospheres,

such as in the presence of ﬂammable liquids, gases or

Safety

dust.

Power tools create sparks which may ignite the dust or

fumes.

-Keep children and bystanders away while operating a

power tool.

Distractions can cause you to lose control.

Electrical safety

-Power tool plugs must match the outlet. Never modify the

plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools.

Unmodiﬁed plugs and

matching outlets will reduce risk of electric shock.

-Avoid body contact with earthed or grounded surfaces,

such as pipes, radiators, ranges and refrigerators.

There is

an increased risk of electric shock if your body is earthed or

grounded.

-Do not expose power tools to rain or wet conditions.

Water

entering a power tool will increase the risk of electric shock.

-Do not misuse the power cord, such as to carry or hang

the power tool or to pull the plug out of the socket. Keep

the power cord away from heat, oil, sharp edges or

moving parts.

Damaged or entangled power cords increase

the risk of electric shock.

-When operating a power tool outdoors, use an extension

cord suitable for outdoor use.

Use of a cord suitable for

outdoor use reduces the risk of electric shock.

-If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply.

Use of an RCD reduces the risk of electric

shock.

Personal safety

-Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a power

Safety

tool while you are tired or under the inﬂuence of drugs,

alcohol or medication.

A moment of inattention while

operating power tools may result in serious personal injury.

-Use personal protective equipment. Always wear eye

protection.

Protective equipment such as a dust mask, non-

skid safety shoes, hard hat or hearing protection used for

appropriate conditions will reduce personal injuries.

-Prevent unintentional starting. Ensure the switch is in the

off-position before connecting to power source and/or

battery pack, picking up or carrying the tool.

Carrying

power tools with your ﬁnger on the switch or energising

power tools that have the switch on invites accidents.

-Remove any adjusting key or wrench before turning the

power tool on.

A wrench or a key left attached to a rotating

part of the power tool may result in personal injury.

-Do not overreach. Keep proper footing and balance at all

times.

This enables better control of the power tool in

unexpected situations.

-Dress properly. Do not wear loose clothing or jewellery.

Keep your hair and clothing away from moving parts.

Loose clothes, jewellery or long hair can be caught in moving

parts.

-If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used.

Use of dust collection can

reduce dust-related hazards.

-Do not let familiarity gained from frequent use of tools

allow you to become complacent and ignore tool safety

principles.

A careless action can cause severe injury within a

fraction of a second.

Safety

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Lijadora de FERREX

FERREX

FERREX YT-7251A Hoja de información del producto

FERREX

FERREX BTS920 Manual de usuario

FERREX

FERREX FASS 20-l Manual de usuario

FERREX

FERREX FAES 20-I Manual de usuario

FERREX

FERREX BDG 915 Manual de usuario

Manuales populares de Lijadora de otras marcas

Oliver

Oliver 6305 Manual de usuario

Jet

Jet 22-44 Pro-3 Manual de servicio

Makita

Makita M9204 Manual

Makita

Makita M9204 Manual de usuario

Craftsman

Craftsman 351.215131 Manual de usuario

Clarke

Clarke Woodworker CBS1-5B Manual de instrucciones

Chicago Pneumatic

Chicago Pneumatic CP9778 Manual de usuario

Nitto Kohki

Nitto Kohki BB-20 Manual de usuario

Ferm

Ferm FEOS-135 Manual de usuario

Unior

Unior 1510 Manual de usuario

stayer

stayer ls1200 Manual de usuario

Jet

Jet JSG-96 Manual de servicio

Parkside

Parkside PDS 290 B2 Manual de usuario

Status

Status XPA Series Manual de usuario

Clarke

Clarke EZ Sand Manual de usuario

Craftsman

Craftsman 113.22521 Manual de usuario

Craftsman

Craftsman 113.225831 Manual de usuario

CLAS

CLAS OP 1429 Manual de usuario