Quick Start Guide
Quick Start Guide
Getting started
Inserting the remote control batteries
Insert the two AAA batteries provided into the remote control as described below:
ANT
R
RLY
Pb/Cb
Pr/Cr
PC/IN
PCAUDIOIN
SCART2-IN
SCART1-IN
DVI
L
R
L
R
L
S-VIDEO
VIDEO
VIDEO
S-IN
AV-IN
AV-OUT
COMPONENTIN
ANT
R
RLY
Pb/Cb
Pr/Cr
PC/IN
PCAUDIOIN
SCART2-IN
SCART1-IN
DVI
L
R
L
R
L
S-VIDEO
VIDEO
VIDEO
S-IN
AV-IN
AV-OUT
COMPONENTIN
Connecting power
ANT port
Basic connections
The ANT jack is provided to directly connect cable TV, satellite or an antenna as follows:
Please refer to the following sections for detailed instructions about connecting the audio/video (AV)
device of your choice to your LCD TV and view your favorite programs or movies. These sections
describe the basic procedures required to set up your TV for easy and convenient viewing.
1.Pull the latch on the battery compartment cover on the
rear of the remote control and remove the cover.
2.Insert the two supplied AAA batteries. Check the +
and - ends of the batteries before inserting them in the
compartment. remote control and remove the cover.
3.Replace the cover and make sure it snaps securely
back into place.
ΘDo not mix old and new batteries or batteries of
different types together.
ΘDo not short circuit, disassemble, heat or fire
batteries.
ΘRemove the batteries to avoid damage from
possible battery leakage if you anticipate that the
remote control will not be used for an extended
period of time.
ΘPlease handle the remote control with care. Avoid
dropping it, getting it wet, or placing it in direct
sunlight, near a heater or in an area of high humidity.
1. Connect the supplied power cord to the AC IN
jack on the rear of your TV.
2. Connect the other end of
the power cord to a power
outlet.
ANT
R
RLY
Pb/Cb
Pr/Cr
PC/IN
PCAUDIOIN
SCART2-IN
SCART1-IN
DVI
L
R
L
R
L
S-VIDEO
VIDEO
VIDEO
S-IN
AV-IN
AV-OUT
COMPONENTIN
1 2 3
The TECO 32-inch LCD Colour Television
provides multiple input and output ports to
enable you to connect different types of
A/V devices such as an antenna or CATV
line, a VCR/VCD/DVD player, a satellite
receiver, or even a PC.
You can also use the LCD TV as a flash
memory card reader and view your digital
photographs or video clips directly on the
TV without requiring a PC connection.
The back panel of the LCD TV provides
input and output jacks to make these
connections possible. The following
sections discuss the various ports and the types of A/V devices that can be connected to your TV.
1.Connect one end of a CATV 75. coaxial cable to the ANT jack on the
rear panel of the TV.
2.Connect the other end of this cable to CATV wall mounting as shown
below on the left. You may also need to use a cable adapter to connect
to your CATV wall mounting, depending on your installation.
If you have subscribed to a
cable TV system using
scrambled or encoded signals
requiring a cable box to view
all channels, connect the the
ANT jack to the cable box's
ANTENNA OUT jack.
It is strongly recommended that you connect the antenna using a 75W coaxial
cable to get optimum picture and sound quality. A 300W twin lead cable can be
easily affected by radio and other background noise, resulting in signal
deterioration. When using a 300W twin lead cable, please keep this cable as far
away from the TV as possible.
Component IN port
The COMPONENT IN port lets you connect your TV to high quality video
equipment such as a DVD player, digital TV receiver, or digital satellite
receiver. This port consists of component audio (L, R) and video (YCbCr or
YPbPr) connectors and provides the highest picture quality. To connect your
A/V device to this port, do the following:
1.Using a component video cable, connect the video (YCbCr/YPbPr) jacks on
the TV to the corresponding video output jacks of your A/V device.
2.Using an audio cable, connect the audio (L, R) jacks on the TV to the
corresponding audio output jacks of your A/V device.
ANT
R
RLY
Pb/Cb
Pr/Cr
PC/IN
PCAUDIOIN
SCART2-IN
SCART1-IN
DVI
L
R
L
R
L
S-VIDEO
VIDEO
VIDEO
S-IN
AV-IN
AV-OUT
COMPONENTIN
YLRCbCr
Video Audio
SCART ports
ANT
R
RLY
Pb/Cb
Pr/Cr
PC/IN
PCAUDIOIN
SCART2-IN
SCART1-IN
DVI
L
R
L
R
L
S-VIDEO
VIDEO
VIDEO
S-IN
AV-IN
AV-OUT
COMPONENTIN
or
The LCD TV has two
SCART (SCART1,
SCART2) ports for
connecting up to two
SCART A/V devices
with the LCD TV.
To connect an A/V
device to the SCART
port, use a SCART
cable to connect the
device to either one
of the SCART ports
on the rear panel of
the LCD TV.
AV IN port AV out port
PC IN port
1.Using an S-Video cable, connect
the video (S-Video) jack on the TV
to the corresponding S-Video
output jack of your A/V device.
2.Using an audio cable, connect the
audio (L, R) jacks on the TV to the
corresponding audio output jacks
of your A/V
device.
S-IN port
ANT
R
RLY
Pb/Cb
Pr/Cr
PC/IN
PCAUDIOIN
SCART2-IN
SCART1-IN
DVI
L
R
L
R
L
S-VIDEO
VIDEO
VIDEO
S-IN
AV-IN
AV-OUT
COMPONENTIN
AV-OUT
S-VIDEO
RL
VIDEO
1.Using a composite video cable, connect the video
(VIDEO) jack on the TV to the video
output jack of your A/V device.
2.Using an audio cable,
connect the audio
(L, R) jacks on the TV
to the corresponding
audio output jacks of
your A/V device.
The AV IN port supports composite video and
provides good quality video. To connect an A/V
device such as a VCR, VCD player, or
DVD player, do the following:
AV-OUT
RL
VIDEO
ANT
R
RLY
Pb/Cb
Pr/Cr
PC/IN
PCAUDIOIN
SCART2-IN
SCART1-IN
DVI
L
R
L
R
L
S-VIDEO
VIDEO
VIDEO
S-IN
AV-IN
AV-OUT
COMPONENTIN
AV-OUT
RL
VIDEO
ANT
R
RLY
Pb/Cb
Pr/Cr
PC/IN
PCAUDIOIN
SCART2-IN
SCART1-IN
DVI
L
R
L
R
L
S-VIDEO
VIDEO
VIDEO
S-IN
AV-IN
AV-OUT
COMPONENTIN
Use the AV OUT port to connect your
LCD TV to an A/V device such as a DVD
recorder, VCR, home theater audio
equipment, and so on, as follows:
1.Using a composite video cable, connect
the video (VIDEO) jack on the TV to the
video input jack of
your A/V device.
2.Using an audio cable,
connect the audio
(L, R) jacks on the TV
to the corresponding
audio input jacks of
your A/V device.
Connect your LCD TV to a PC or portable computer with the
PC IN port, to use the LCD TV as a monitor for your PC. To connect
to a PC, do the following:
1.Connect the video output of your PC or portable computer to
the PC IN (VGA) video input on the back panel of the TV using a
VGA cable.
2.Connect the Line out audio output of your PC to the
PC AUDIO IN jack of the TV.
ANT
R
RLY
Pb/Cb
Pr/Cr
PC/IN
PCAUDIOIN
SCART2-IN
SCART1-IN
DVI
L
R
L
R
L
S-VIDEO
VIDEO
VIDEO
S-IN
AV-IN
AV-OUT
COMPONENTIN
FL32WX2
