Disclaimer
Always boat responsibly. Before starting, know your boat and waterway rules. Always follow your
boat manufacturer’s procedures of operation. Never overload the boat and be sure to wear your
life jacket at all times. Check your boat for all required safety equipment and never operate a
boat under the inuence of alcohol. Check your local weather forecast before
leaving the dock and always provide a oat plan to your marina, member of your family or friend.
In no event shall FELL AS and its subsidiaries and/or its suppliers, agents or aliates be
liable for any direct, indirect, punitive, incidental, special consequential damages, to property or
life, whatsoever arising out of or connected with the improper installation, misuse,
improper maintenance, self-repair, or tampering of our products.
EMC Installation Guidelines
FELL equipment and accessories are designed to the best industry standards for use in the
recreational marine environment. Their design and manufacture conforms to the appropriate
Electromagnetic Compatibility (EMC) regulations, but correct installation is required to ensure
that performance is not compromised.
The guidelines given here describe the conditions for optimum EMC performance, but it is recog-
nized that it may not be possible to meet all of these conditions in all situations. To ensure the
best possible conditions for EMC performance within the constraints imposed by any location,
always ensure the maximum separation possible between dierent items of electrical equipment.
For optimum EMC performance, it is recommended that wherever possible:
• FELL equipment and the cables connected to it are:
• At least 3 ft (1 m) from any equipment transmitting or cables carrying radio signals e.g. VHF
radios, cables and antennas. In the case of SSB radios, the distance should be increased to
7 ft (2 m).
• More than 7 ft (2 m) from the path of a radar beam. A radar beam can normally be assumed to
spread 20 degrees above and below the radiating element.
• If possible the product is supplied from a separate battery from that used for engine start.
Power supply voltages below the minimum specied for a product, and starter motor transients,
can cause the product to reset. This will not damage the product, but may cause the loss of
some information and may change the operating mode.
• FELL specied cables are used. Cutting and rejoining these cables can compromise EMC
performance and must be avoided unless doing so is detailed in the installation manual.
Important information and caution
Read all instructions carefully before use of this product.
FELL Marine equipment and accessories are designed to the best industry standards for use in
the recreational marine environment. Their design and manufacture conforms to the appropriate
Electromagnetic Compatibility (EMC) regulations, but correct installation is required to ensure
that performance is not compromised. Please see section EMC Installation Guidelines in the
User Manual for optimum EMC conditions.
Within the wireless range MOB+ will not shut down the engine automatically e.g. if you fall in
your boat within the wireless range the engine will not stop automatically. In this event, you
can shut down the engine by pressing the button on your MOB+ xFOB or on the MOB+ xHUB.
Always check your wireless range before use.
Make sure that the system is working properly before leaving the dock. Refer to the section
Using WiMEA in the User Manual for instructions on how to use the system and information
about normal system operations.
Always make sure to check the battery level sign on the xHUB before driving the boat. Confer
with section Battery Indication in the User Manual to check how many hours there are left of
battery life on the xFOB.
Never attempt fast speed or dangerous maneuvers of the boat, especially if battery level is low
on the xFOB. Battery depletion of xFOB can cause sudden engine stop and result in loss of
control or maneuverability of the boat.
Never attempt any service of inside components in either the xHUB or the xFOB.
Warranty, Important Product- and Safety Information
Failure to avoid the following potentially hazardous situations could result in an accident or
collision resulting in death or serious injury.
Disclaimer
By using this device you agree upon all the following guidelines and information provided in
this document. Read all instructions carefully before using this device. Always boat responsibly.
Before starting, know your boat and waterway rules. Always follow your boat manufacturer’s
procedures of operation. Never overload the boat and be sure to wear your life jacket at all
times. Check your boat for all required safety equipment and never operate a boat under the
inuence of alcohol. Check your local weather forecast before leaving the dock and always
provide a oat plan to your marina, member of your family or friend. In no event shall FELL and
its subsidiaries and/or its suppliers, agents or aliates be liable for any direct, indirect, punitive,
incidental, special consequential damages, to property or life, whatsoever arising out of or
connected with the improper installation, use, misuse, improper maintenance, self-repair, or
tampering of our products.
Marine Operation Warnings
• You are responsible for the safe and prudent operation of your vessel. This device is
a tool to enable you to enhance your safety while operating your vessel. It does not
relieve you from the responsibility of safely operating your vessel. Avoid navigational
hazards and never leave the helm unattended.
• Always drive the boat carefully and in accordance with local laws.
• Use this device only as a safety aid. This device does not replace the cord based kill
switch, and should be used at your own discretion and responsibility, knowing that
in the event that you fall in your vessel the system may not automatically shut down
your engine.
• This device will shut down your engine and give an alarm signal when you are out of
wireless range or falls into the water within 2 seconds. Within the wireless range this
device will not shut down the engine automatically e.g. if you fall in your boat within the
wireless range the engine will not stop automatically. In this event, you can shut down
the engine by pressing the button on your MOB+ xFOB or on the MOB+ xHUB. Always
check your wireless range before use. The wireless range may vary from 5 – 20 meters
depending on the wireless environment surrounding your vessel.
• Make sure that the system is working properly before leaving the dock. Refer to the
section Using MOB+ in the User Manual for instructions on how to use the system and
information about normal system operations.
• Always make sure to check the battery level sign on the xHUB before operating your
vessel. Confer with section Battery Indication in the User Manual to check how many
hours there are left of battery life on the xFOB.
• Never attempt fast speed or dangerous maneuvers of the boat, especially if battery
level is low on the xFOB. Battery depletion of xFOB can cause sudden engine stop and
result in loss of control or maneuverability of the boat.
• Do not leave your xFOB in the boat unobserved, this to prevent easy theft of the boat
if the ignition key is also situated in the vessel. Please refer to the engine manufacturer
for information regarding ignition and starting procedure of the engine.
Other safety Considerations
Small parts contained in your device and its accessories may present a choking hazard to small
children. Personal medical devices, such as pacemakers, may be sensitive to magnetic and
electromagnetic elds. Since this device contain magnets and emit electromagnetic elds, they
should be kept at least 30 cm from any personal medical device. If any interference is observed,
consult with your physician before resuming use. Items with magnetically-stored data, such as
credit cards and hard drives, may also be sensitive to magnetic or electromagnetic elds, and
should not be placed near this device.
CE Declaration of Conformity
FELL equipment and accessories are designed to the best industry standards for use in the
recreational marine environment. Their design and manufacture conforms to the appropriate
Electromagnetic Compatibility (EMC) regulations, but correct installation is required to ensure
that performance is not compromised. Please see section EMC Installation Guidelines in the
User Manual for optimum EMC conditions. Products sold in the EU/EEA is in compliance with the
essential requirements and other relevant provisions of R&TTE Directive 1999/5/EC.
CE SAR Compliance
This device meets the EU requirements (1999/519/EC) on the limitation of exposure of the
general public to electromagnetic elds by way of health protection. The limits are part of
extensive recommendations for the protection of the general public. These recommendations
have been developed and checked by independent scientic organizations through regular and
thorough evaluations of scientic studies. The unit of measurement for the European Council’s
recommended limit for mobile devices is the ”Specic Absorption Rate” (SAR), and the SAR
limit is 2.0 W/ kg averaged over 10 gram of tissue. It meets the requirements of the International
Commission on Non-Ionizing Radiation Protection (ICNIRP).
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation. Note:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
o and on, the user is encouraged to try to correct the interference by one or more of the
following measures: Reorient or relocate the receiving antenna, Increase the separation between
the equipment and receiver, Connect the equipment into an outlet on a circuit dierent from that
to which the receiver is connected, Consult the dealer or an experienced radio/TV technician for
help. MOB+ xHUB: This device complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. The antenna used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-located or operating
in conjunction with any other antenna or transmitter. MOB+ xFOB: This device is exempted from
FCC SAR testing since the RF Output Power is below the exemption limit.
Wireless Safety and Compliance
Turn your wireless connection o in areas where wireless use is forbidden or when it may cause
interference or danger. Some specic situations are described below. In general, you should not
use your FELL devices with your wireless connection turned on any place you are not allowed
to use a cellular device. To prevent possible interference with aircraft systems, aviation agencies
require you to have permission from a crewmember to use your device’s wireless service. We do
not recommend to use FELL devices when ying.
Battery Information
Standard battery used in this device from manufacturing is:
Panasonic – BCG BATTERY LITHIUM COIN 3V 20MM CR2032. Lead free / RoHS compliant
by exemption.
Manufacturer Part Number: CR2032L/BE.
Panasonic CR2032L/BE Specication Datasheet for battery can be found here: https://s3-eu-
west-1.amazonaws.com/generalweb/productinfo/panasonic_cr2032_datasheet.pdf
Panasonic CR2032L/BE MSDS Safety Datasheet can be found here: https://s3-eu-west-1.
amazonaws.com/generalweb/productinfo/panasonic_cr2032_productsafety.pdf
FELL recommend using the above battery when changing battery in MOB+ xFOB device, to
ensure wireless connection quality and battery life performance.
Recycling
In some areas, the disposal of certain electronic devices is regulated. Make sure you dispose of
or recycle all FELL devices in accordance with your local laws and regulations.
Other Electronic Devices
FELL devices generates, uses, and radiate radio frequency (RF) energy and, if not used in
accordance with its instructions, may cause interference to radio communications and electronic
equipment, i.e. if hardware or software is being tampered with or the device has become broken.
FELL devices are designed and manufactured to only communicate with FELL devices. External
RF signals may aect improperly installed or inadequately shielded electronic operating systems,
entertainment systems, and personal medical devices. While most modern electronic equipment
is shielded from external RF signals, if in doubt, check with the manufacturer or contact FELL
for support. For personal medical devices (such as pacemakers and hearing aids), consult with
your physician or the manufacturer to determine if they are adequately shielded from external
RF signals, showing this user guide to the respective physician or manufacturer. In the unlikely
event that you experience interference with other electronic devices, please contact customer
support on: www.fellmarine.com/support or contact the manufacturer of the respective electronic
device. There are some places where RF signals could constitute a hazard, such as health care
facilities, and construction sites. If you are not sure, look around for signs indicating that two-
way radios or cell phones should be turned o.
Patent notice
The FELL devices and/or methods used in association with the FELL devices may be covered by
one or more patents or pending patent applications.
Limited Warranty
This FELL product is warranted to be free from defects in materials or workmanship for two years
from the date of purchase. Within this period, FELL will, at its sole option, repair or replace any
components that fail in normal use. Such repairs or replacements will be made at no charge to the
customer for parts or labor, provided that the customer shall be responsible for any transportation
cost. This warranty does not apply to: (i) cosmetic change, such as scratches, nicks and dents;
(ii) consumable parts, such as batteries, unless product damage has occured due to the defect in
materials or workmanship; (iii) damage caused by accident, abuse, misuse, water, ood, re, or
other acts of nature or external causes; (iv) damage caused by service performed by anyone who
is not an authorized service provider of FELL, or (v) damage to a product that has been modied or
altered without the written permission of FELL, or (vi) damage to a product that has been connected
to power and/or data cables that are not supplied by FELL. In addition, FELL reserves the right to
refuse warranty claims against products or services that are obtained and/or used in contravention
of the laws of any country. Repairs have 180 day warranty. If the unit sent in is still under its
original warranty, then the new warranty is 180 days or to the end of the original two year warranty,
depending on which is longer. For specic instructions about how to obtain warranty service for your
device, please contact FELL support. THE WARRANTIES AND REMEDIES CONTAINED HEREIN
ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES EXPRESS, IMPLIED, OR STATU-
TORY, INCLUDING ANY LIABILITY ARISING UNDER ANY WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE, STATUTORY OR OTHERWISE. THIS WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH MAY VARY FROM STATE/COUNTRY TO STATE/
COUNTRY. IN NO EVENT SHALL FELL, ITS SHAREHOLDERS, BOARD OF DIRECTORS, OR
EXECUTIVE LEADERS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSE-
QUENTIAL DAMAGES, WHETER RESULTING FROM THE USE, MISUSE, OR INABILITY TO USE
THIS PRODUCT OR FROM DEFECTS IN THE PRODUCT. SOME STATES/COUNTRIES DO NOT
ALLOW THE EXCLUSION OF INCIDENTIAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS MAY NOT APPLY TO YOU. SOME JURISDICTIONS DO NOT ALLOW LIMITATIONS
ON HOW LONG A STATUTORY OR IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION
MAY NOT APPLY TO YOU. This limited warranty gives you specic rights. You may have additional
rights under applicable law, and this limited warranty does not aect such rights. FELL retains
the exclusive right to repair or replace (with a new or newly-overhauled replacement product) the
device or software or oer a full refund of the purchase price at its sole discretion. SUCH REMEDY
SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY. To
obtain warranty service, contact your local FELL authorized dealer or call FELL Support for shipping
instructions and an Return Ticket Number. Securely pack the device and a copy of the original sales
receipt, which is required as the proof of purchase for warranty repairs. Write the tracking number
clearly on the outside of the package. Send the device, freight charges prepaid, to your nearest
FELL address. See www.fellmarine.com to nd your nearest address for return or contact your local
FELL dealer.
ONLINE AUCTION PURCHASES: Products purchased through online auctions are not eligible for
rebates or other special oers from FELL warranty coverage. Online auction conrmations are not
accepted for warranty verication. To obtain warranty service, an original or copy of the sales receipt
from the original retailer is required. FELL will not replace missing components from any package
purchased through an online auction.
FOR INTERNATIONAL PURCHASES: A separate warranty may be provided by international
distributors for devices purchased outside Norway or the United States depending on country. If
applicable, this warranty is provided by the local in-country distributor and this distributor provides
local service for your device. Distributor warranties are only valid in the area of intended distribution.
FOR AUSTRALIAN CONSUMERS: Our goods come with guarantees that cannot be excluded
under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure
and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does
not amount to a major failure. Goods presented for repair may be replaced by refurbished goods of
the same type rather than being repaired. Refurbished parts may be used to repair the goods.
Warranty provider
FELL AS Nedre Storgate 46, N-3015 Drammen,Norway
Org.No: 912 282 554 - Website: www.fellmarine.com - Tel: +47 32 82 82 80
Additional information
www.fellmarine.com
www.fellmarine.com/support
© FELL AS, Nedre Storgate 46, N-3015, Drammen, Norway. FELL®, WiMEA®, WiMEA Protocol,
MOB+, xHUB, xFOB, xTAG and its logos are trademarks of FELLAS, its subsidiaries and
aliates. The shape and design of this product are a trademark of FELL AS, subsidiaries and
aliates. NMEA®, NMEA 2000®, and the NMEA 2000 logo are registered trademarks of the
National Marine Electronics Association. All other trademarks or registered trademarks are the
property of their respective owners. Designed in Norway. Made in China and Taiwan. All rights
reserved. Product features, appearances and specications may be subject to change without
notice. Read all instructions carefully before use. Visit www.fellmarine.com/support for complete
Owner’s Manual. Pleaseretain this information for future reference.
Changes or modications to the equipment not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
MOB+ xHUB: This device complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. The antenna used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.
MOB+ xFOB: This device is exempted from FCC SAR testing since the RF Output Power is
below the exemption limit.
California ONLY: Perchlorate Material - special handling may apply,
See: http://www.dtsc.ca.gov/hazardouswaste/perchlorate
Déclaration d’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20
cm de distance entre la source de rayonnement et votre corps.
Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environ-
ment. This equipment should be installed and operated with minimum distance 20 cm between
the radiator & your body.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation
of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes
: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
WARNING: CHOKING HAZARD
Small parts. Not for children under 3 years
Norway
FELL AS
Nedre Storgate 46
N-3015, Drammen
www.fellmarine.com
MOB+ xFOB Model: GU90115 FCC ID: 2AFOZGU90115 IC: 20622-GU90115
MOB+ xHUB Model: BU90115 FCC ID: 2AFOZBU90115 IC: 20622-BU90115
Product contains CR2032 Lithium-ion Coin Cell Battery
Product category: Marine electronics
Designed in Norway, Printed in China
Tested to comply with FCC standards.
Package contents: MOB+ xHUB, MOB+ xFOB, External Antenna, Connection Cable, Butt
splices, Battery and User Guide.
Voir www.fellmarine.com/support pour des informations
importantes, consignes d’installation CEM, la garantie et exclusions
en français.
Ver www.fellmarine.com/support para obtener información importante,
pautas para la instalación de EMC la garantía y limitaciones de
responsabilidad en Español.
Siehe www.fellmarine.com/support für wichtige Informationen,
EMV-Installationsrichtlinien Gewährleistung und Haftungsausschlüsse
in deutscher Sprache.
