Fein BLK1.3TE Guía de configuración
Repair instructions
C-SC_CSSM 2012.07
All rights reserved by FEIN, especially in case of industrial rights registration.
FEIN retains all rights of disposal, such as copying and circulation. 2/38
Contents
1. Models described
2. Technical data
3. Provisions
4. Tools required
5. Lubricants and auxiliary substances required
6. Disassembly
7. Assembly
8. Connection diagram
Repair instructions
C-SC_CSSM 2012.07
All rights reserved by FEIN, especially in case of industrial rights registration.
FEIN retains all rights of disposal, such as copying and circulation. 3/38
1. Models described
These instructions describe how to repair the following models:
Model Order no.
BLK 1.3 TE 723241
BLK 1.3 CSE 723242
BLK 1.6E 723238
BLK 1.6LE 723239
BLK 2.0E 723240
Repair instructions
C-SC_CSSM 2012.07
All rights reserved by FEIN, especially in case of industrial rights registration.
FEIN retains all rights of disposal, such as copying and circulation. 4/38
2. Technical data
Technical data
The complete technical data can be found in the operating instructions for the model.
Test data
Up-to-date test data for all models can be found on the FEIN Extranet (Customer Service → Repair Guides).
Lubricants
Lubricants and container sizes available from FEIN can be found on the FEIN Extranet
(Customer Service → Repair Guides).
Lists of spare parts
Lists of spare parts and exploded views are available online at www.fein.com
Repair instructions
C-SC_CSSM 2012.07
All rights reserved by FEIN, especially in case of industrial rights registration.
FEIN retains all rights of disposal, such as copying and circulation. 5/38
3. Provisions
Provisions
Please note that power tools may only be repaired, maintained and checked by a trained
electrician, as improper repair can result in serious risks to the user.
The provisions set out in DIN VDE 0701-0702 should be observed after repairs.
Only use original FEIN spare parts!
The relevant accident prevention regulations of the employers’ liability insurance associations are
to be observed when commissioning.
The German Equipment and Product SafetyAct applies for correct use.
Outside Germany, the regulations applicable in the relevant country must be observed!
Repair instructions
C-SC_CSSM 2012.07
All rights reserved by FEIN, especially in case of industrial rights registration.
FEIN retains all rights of disposal, such as copying and circulation. 6/38
4. Tools required
Standard tools
Open-ended spanner: WAF 30
Plastic hammer
Screwdriver: Torx 15
Flat nose pliers
Long-nosed pliers
Circlip pliers
Punch
Arbor press
Cable hooks
Sleeves
Special tools
Drawing-off socket cap 6 41 04 150 00 8
Chuck cone 6 41 07 019 00 7
Chuck cone 6 41 07 026 00 0
Press-in fixture 6 41 22 108 00 0
Repair instructions
C-SC_CSSM 2012.07
All rights reserved by FEIN, especially in case of industrial rights registration.
FEIN retains all rights of disposal, such as copying and circulation. 7/38
5. Lubricants and auxiliary substances required
Lubricants
Grease 0 40 108 0400 8 15 g Gearbox, needle bearing, ball bearing
Grease 0 40 119 0500 7 Sliding surfaces of plunger, con rod, punch
Auxiliary substances
Loctite 574 Between gearbox head and intermediate bearing
Repair instructions
C-SC_CSSM 2012.07
All rights reserved by FEIN, especially in case of industrial rights registration.
FEIN retains all rights of disposal, such as copying and circulation. 8/38
4. Disassembly
Before starting to remove the
motor or gearbox, the tool must always be disconnected from
the mains.
Repair instructions
C-SC_CSSM 2012.07
All rights reserved by FEIN, especially in case of industrial rights registration.
FEIN retains all rights of disposal, such as copying and circulation. 9/38
4.1. Disassembly - Motor
1.Remove screws and lift off cover.
2.Unscrew carbon holder.
3.Unscrew traction relief.
4.Unscrew plug connection between motor and electronics.
Tool:
- Screwdriver
Torx 15
Repair instructions
C-SC_CSSM 2012.07
All rights reserved by FEIN, especially in case of industrial rights registration.
FEIN retains all rights of disposal, such as copying and circulation. 10/38
4.2. Disassembly - Separating motor and gearbox
1.Remove screws.
2.Remove gearbox housing with armature from motor housing.
3.Remove sealing ring from intermediate bearing.
4.Remove intermediate gear shaft from intermediate bearing or gearbox housing.
5.Remove air guide ring.
Tool:
- Screwdriver
Torx 15
- Plastic hammer
Otros manuales para BLK1.3TE
3
Este manual sirve para los siguientes modelos
9
Tabla de contenidos
Otros manuales de Herramientas eléctricas de Fein
Fein
Fein ASt638 Manual de usuario
Fein
Fein ASAS18-21KAS Series Manual de usuario
Fein
Fein AFSC18Q Manual de usuario
Fein
Fein KBM 50 auto Guía de configuración
Fein
Fein 7 272 Manual de usuario
Fein
Fein CCG18-115-10PD-SEC AS Series Manual de usuario
Fein
Fein KFH17-15 Series Manual de usuario
Fein
Fein 7 232 32/BLK 1.6 Guía de configuración
Fein
Fein AMM700 1.7Q AS Manual de usuario
Fein
Fein BLK1.3TE Manual de usuario
Fein
Fein KBB30 Manual de usuario
Fein
Fein BLs 1.6 Manual de usuario
Fein
Fein AFSC18Q Manual de usuario
Fein
Fein AMM 300 Plus Series Manual de usuario
Fein
Fein AFMM 18 Manual de usuario
Fein
Fein KBH25 Instrucciones de funcionamiento
Fein
Fein ASCT5-40 Manual de usuario
Fein
Fein MULTIMASTER FMM 250 Q Manual de usuario
Fein
Fein BLS 1.6 E Manual de usuario
Fein
Fein AMM 700 1.7Q Series Manual de usuario
