Feig Electronic ID ISC.ANT1300/680 Type A Manual de usuario
INSTALLATION
final
public (B)
2011-08-17
M71104-6e-ID-B.doc
ID ISC.ANT1300/680
Type A and Type B
Version: Reader ID ISC.LRM2000-C, manual tuning board
English
OBID i-scan®
Installation
ID ISC.ANT1300/680-A/-B
FEIG ELECTRONIC GmbH
Page 2 of 45
M71104-6e-ID-B.doc
Note
Copyright 2011 by
FEIG ELECTRONIC GmbH
Lange Straße 4
D-35781 Weilburg
Tel.: +49 6471 3109-0
http://www.feig.de
With the edition of this document, all previous editions become void. Indications made in this manual may be
changed without previous notice.
Copying of this document, and giving it to others and the use or communication of the contents thereof are
forbidden without express authority. Offenders are liable to the payment of damages. All rights are reserved
in the event of the grant of a patent or the registration of a utility model or design.
Composition of the information in this document has been done to the best of our knowledge. FEIG
ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this
manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since,
despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips.
The instructions given in this manual are based on advantageous boundary conditions. FEIG ELECTRONIC
GmbH does not give any guarantee promise for perfect function in cross environments and does not give
any guaranty for the functionality of the complete system which incorporates the subject of this document.
FEIG ELECTRONIC call explicit attention that devices which are subject of this document are not designed
with components and testing methods for a level of reliability suitable for use in or in connection with surgical
implants or as critical components in any life support systems whose failure to perform can reasonably be
expected to cause significant injury to a human. To avoid damage, injury, or death, the user or application
designer must take reasonably prudent steps to protect against system failures.
FEIG ELECTRONIC GmbH assumes no responsibility for the use of any information contained in this docu-
ment and makes no representation that they free of patent infringement. FEIG ELECTRONIC GmbH does
not convey any license under its patent rights nor the rights of others.
OBID®and OBID i-scan®are registered trademarks of FEIG ELECTRONIC GmbH.
I-CODE®is a registered trademark of Philips Electronics N.V.
Tag-itTM is a registered trademark of Texas Instruments Incorporated.
OBID i-scan®
Installation
ID ISC.ANT1300/680-A/-B
FEIG ELECTRONIC GmbH
Page 3 of 45
M71104-6e-ID-B.doc
Contents
1Safety Instructions / Warning - Read before Start-Up ! 5
2Performance Features of the ID ISC.ANT1300/680 Antennas 6
2.1 Available Antenna Types ...........................................................................................6
3Installation and Wiring 7
3.1 Dimensions of antenna .............................................................................................. 7
3.2 Mounting preparation................................................................................................8
3.3Installing the antenna.................................................................................................9
3.3.1 Drilling the Mounting Holes ......................................................................................9
3.3.2 Installing the Antenna Base and Antenna Body......................................................11
3.3.3 Connection of components.....................................................................................11
4Typical Antenna Configuration (Gate Antenna with two Antennas) 12
4.1 Project Notes ............................................................................................................ 12
4.2 Gate Configuration and Setup using Antennas Type –A and Type –B/-BL .......... 15
4.2.1 Required Components ...........................................................................................15
4.2.2 Configuration of a Gate antenna with Power Splitter .............................................. 16
4.2.3 Setting the Power Splitter.......................................................................................18
4.2.4 Setting the Antenna Tuner .....................................................................................19
4.2.5 Interface Connections ............................................................................................21
4.2.5.1 RS 232.........................................................................................................21
4.2.5.2 LAN / TCP/IP................................................................................................22
4.2.6 Reader Configuration with Power Splitter...............................................................23
4.2.7 Tuning the Gate Antenna with Power Splitter.........................................................26
4.3 Testing the Gate Antenna.........................................................................................28
4.3.1 Checking the Noise Level....................................................................................... 28
4.3.2 Reading a Serial Number....................................................................................... 29
4.3.3 Testing the performance ........................................................................................30
4.4 Connecting and Setting the Indicators....................................................................32
OBID i-scan®
Installation
ID ISC.ANT1300/680-A/-B
FEIG ELECTRONIC GmbH
Page 4 of 45
M71104-6e-ID-B.doc
4.4.1 Connecting the Alarm LED.....................................................................................32
4.4.2 Reader Setting for Indicator....................................................................................33
4.4.3 Programming a Transponder with the AFI Byte......................................................35
4.5 Activating the Automatic Mode................................................................................36
4.6 Configuring the Reader in accordance with national RF regulations...................37
5Technical Data 39
5.1 Antenna ID ISC.ANT1300/680 - Type A and Type B................................................ 39
5.2 Approval.................................................................................................................... 42
5.2.1 Europe (CE)...........................................................................................................42
5.2.2 USA (FCC) and Canada (IC).................................................................................. 43
6Annex A 44
6.1 Terminal assignment “Terminal Board”.................................................................. 44
6.2 Sources of supply measuring instruments and accessories ................................ 45
OBID i-scan®
Installation
ID ISC.ANT1300/680-A/-B
FEIG ELECTRONIC GmbH
Page 5 of 45
M71104-6e-ID-B.doc
1 Safety Instructions / Warning - Read before Start-Up !
The device may only be used for the intended purpose designed by for the manufacturer.
The operation manual should be conveniently kept available at all times for each user.
Unauthorized changes and the use of spare parts and additional devices which have not been
sold or recommended by the manufacturer may cause fire, electric shocks or injuries. Such
unauthorized measures shall exclude any liability by the manufacturer.
The liability-prescriptions of the manufacturer in the issue valid at the time of purchase are valid
for the device. The manufacturer shall not be held legally responsible for inaccuracies, errors,
or omissions in the manual or automatically set parameters for a device or for an incorrect
application of a device.
Repairs may only be executed by the manufacturer.
Installation, operation, and maintenance procedures should only be carried out by qualified
personnel.
Use of the device and its installation must be in accordance with national legal requirements
and local electrical codes .
When working on devices the valid safety regulations must be observed.
Please observe that some parts of the device may heat severely.
Before touching the device, the power supply must always be interrupted. Make sure that the
device is without voltage by measuring. The fading of an operation control (LED) is no indicator
for an interrupted power supply or the device being out of voltage!
For installation and dismantling you should wear suitable safety gloves, because parts of an-
tenna housing could be sharp-edged.
CAUTION! The Antenna-Tuner and the Antenna conductor carry voltages up to
1000V.
Special advice for wearers of cardiac pacemakers:
Although this device doesn't exceed the valid limits for electromagnetic fields you should keep
a minimum distance of 25 cm between the device and your cardiac pacemaker and not stay in
an immediate proximity of the reader’s antennas for any length of time.
OBID i-scan®
Installation
ID ISC.ANT1300/680-A/-B
FEIG ELECTRONIC GmbH
Page 6 of 45
M71104-6e-ID-B.doc
2 Performance Features of the ID ISC.ANT1300/680 Antennas
The ID ISC.ANT1300/680-A antenna is a version with integrated Manual Antenna Tuning Board ID
ISC.MAT , Long Range Reader ID ISC.LRM2000-C, Power Splitter Module ID ISC.PSM, Alarm
LED and Sounder mounted.
The ID ISC.ANT1300/680 Type B antenna is a version with Manual Tuning Board ID ISC.MAT
mounted.
The ID ISC.ANT1300/680 Type BL antenna is a version with Manual Tuning Board ID ISC.MAT
and Alarm LED mounted.
Up to
-two antennas with reader and power splitter as a single gate,
can be operated.
Depending on the antenna configuration, one, two or all three read orientations of the Smart Tags
and various antenna spacing (gate widths) are possible.
The ID ISC.ANT1300/680 –A/-B/-BL is a „figure-of-eight“ antenna with tuner and have been
optimized as transmitting and receiving antennas for the ID ISC.LR2000 Reader. It is however also
possible to operate them with other Readers at a transmission frequency of 13.56 MHz and an
output impedance of 50 . The read ranges indicated in this document and the tuning procedures
may however then vary.
The antennas comprise the electrical antenna conductor, the housing, the ID ISC.MAT Manual
Antenna Tuner and the connection cable.The antennas are factory tuned to an impedance of 50
in a magnetically neutral environment at a distance of 90 cm. When installing in different ambient
conditions the antenna can be retuned using a suitable measuring device (e.g. SWR-Meter). After
tuning the antennas will retain their settings as long as the ambient conditions remain unchanged.
The antennas can be used for detecting both product and persons. It is suitable for installation
indoors or outdoors if weather-protected.
2.1 Available Antenna Types
The following products are currently available:
Antenna Type
Description
ID ISC.ANT1300/680-A
Antenna with Reader, Power Splitter and manual tuning board,
Alarm LED and Sounder
ID ISC.ANT1300/680-BL
Antenna with manual tuning board ID ISC.MAT and Alarm LED
ID ISC.ANT1300/680-B
Antenna with manual tuning board ID ISC.MAT
ID ISC.ANT1300680-SIG
Light signal with mounting material
Table 1: Available Antenna Types and accessories
OBID i-scan®
Installation
ID ISC.ANT1300/680-A/-B
FEIG ELECTRONIC GmbH
Page 7 of 45
M71104-6e-ID-B.doc
3 Installation and Wiring
3.1 Dimensions of antenna
The outside dimensions of the antenna are shown in Fig. 1
Fig. 1: Antenna outside dimensions
All dimensions are in mm with general tolerance to ISO 2768 m (mean).
OBID i-scan®
Installation
ID ISC.ANT1300/680-A/-B
FEIG ELECTRONIC GmbH
Page 8 of 45
M71104-6e-ID-B.doc
3.2 Mounting preparation
For assembly the antenna must be carefully unpacked. This is done as described in the following
steps:
1. Place the packed antenna on the floor with the top side facing up. Carefully open the box and
then remove the antenna.
Fig. 2: Antenna in its packaging
2. After that the antenna has to be placed carefully again on the floor. Now you must remove the
two fastening screws (hexagon socket width A/F2,5) of the antenna base cover and remove it
upwards. Fig. 3
Step 1
Step 2
Fig. 3: Opening the antenna base
OBID i-scan®
Installation
ID ISC.ANT1300/680-A/-B
FEIG ELECTRONIC GmbH
Page 9 of 45
M71104-6e-ID-B.doc
3.3 Installing the antenna
Notes:
Before installing the antennas please read 4.1 Project Notes .The spacing of the antennas
in a gate depends on the antenna configuration.
If multiple antennas or gates are connected to different Readers, a minimum separation of
8 m must be kept between the antennas or gates. For shorter distances the antennas must
be shielded from each other. Otherwise the Reader range will be significantly reduced. The
antennas must have a minimum distance of 20 cm from all larger metal parts! At a distance
of less than 50 cm between the antenna and metal parts the Reader range will be
significantly reduced.
3.3.1Drilling the Mounting Holes
If the position of the antennas has been marked or determined, the antenna base , which has to
be used as a hole template, can be used to mark and drill the mounting holes and the holes for the
cable entry. The dimensions are shown in Fig. 4:
Fig. 4: Floor plate dimensions
All dimensions are in mm with general tolerance to ISO 2768 m (middle).
OBID i-scan®
Installation
ID ISC.ANT1300/680-A/-B
FEIG ELECTRONIC GmbH
Page 10 of 45
M71104-6e-ID-B.doc
The size and type of the screw anchors depends considerably on the strength of the base or floor.
The anchors should be capable of withstanding a permissible load of at least 5 kN per anchor for
all load directions (e.g. for concrete floor Hilti HVA anchors with HAS-(E) M8 threaded rod or Hilti
HIS-N M8 (5/16”) threaded inserts). The size of the mounting holes in the antenna is 10 mm (.39”).
The length of the anchors or bolts should be selected such that they extend at least 50 mm (2.0”)
and a maximum of 65 mm (2.6”) from the floor.
Please follow the mounting instructions of the anchor manufacturer!
Two cable openings are provided for the necessary connection cable (see Fig. 4). The cable
openings are dimensioned such that up to 10 cables having a diameter of 6 mm can be passed
through each opening.
We recommend routing the antenna cables through the cable opening on the Power-Splitter or
Multiplexer side. All other cables such as the supply voltage and multiplexing cable should be
routed through the cable opening on the Reader side.
Alternatively the cables can be routed at the sides of the antenna bas like shown in Fig. 5
Fig. 5 Cable routing at the antenna sides
Otros manuales para ID ISC.ANT1300/680 Type A
1
Tabla de contenidos
Manuales populares de Panel táctil de otras marcas
IBASE Technology
IBASE Technology ASTUT-152-RE1S Manual de usuario
YASKAWA
YASKAWA TP 610C Manual de usuario
B&R
B&R Power Panel C Series Manual de usuario
Beijer Electronics
Beijer Electronics X2 control Manual de usuario
AXIOMTEK
AXIOMTEK GOT321W-521 Manual de usuario
TRIDONIC.ATCO
TRIDONIC.ATCO x-touchBOX Manual de usuario
