Feider Machines FPO350B Manual de usuario

ORIGINAL INSTRUCTIONS

ORBITAL SANDER

FPO350B

WARNING! PLEASE READ THESE INSTRUCTIONS BEFORE USE THIS MACHINE.

BUILDER SAS

32, rue Aristide Bergès-ZI 31270 Cugnaux, France

MADE IN PRC

1. SAFETY WARNINGS

General power tool safety warnings

WARNING Read all safety warnings, instructions, illustrations and specifications

provided with this power tool. Failure to follow all instructions listed below may result in

electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while operating a power tool. Distractions can

cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not

use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is earthed

or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a residual current

device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol

or medication. A moment of inattention while operating power tools may result in serious

personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective equipment

such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or energising power tools that have the

switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a

key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing

away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used. Use of dust collection can reduce

dust-related hazards.

h) Do not let familiarity gained from frequent use of tools allow you to become

complacent and ignore tool safety principles. A careless action can cause severe injury

within a fraction of a second.

4) Power tool use and care

a) Do not force the power tool. Use the correct power tool for your application. The

correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or remove the battery pack, if

detachable, from the power tool before making any adjustments, changing accessories,

or storing power tools. Such preventive safety measures reduce the risk of starting the

power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e) Maintain power tools and accessories. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired before use. Many accidents are

caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc. in accordance with these

instructions, taking into account the working conditions and the work to be performed.

Use of the power tool for operations different from those intended could result in a hazardous

situation.

h) Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery

handles and grasping surfaces do not allow for safe handling and control of the tool in

unexpected situations.

5) Service

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

3, Warning symbol

WARNING-To reduce the risk of injury, user must read instruction manual.

Always wear ear protection

Always wear goggles

Always wear a breathing mask

In accordance with essential applicable safety standards of European directives

3.1Machine-related safety instructions

– Harmful/toxic dust can be produced during your work (e.g. lead-containing

paint, some types of wood and metal). Contact with this dust, especially

inhaling it, can represent a hazard for operating personnel or persons in the

vicinity. Comply with the safety regulations that apply in your country. Connect

the electric power tool to a suitable extraction system.

To protect your health, wear a P2 protective mask.

Always wear protective goggles to protect against sanding hazards.

–Use a residual current protective device when metal grinding,

as well as when the operation of the power tool in a wet environment

cannot be avoided. In the event of an electric shock, the protective switch

protects you against life-threatening current through the body.

– Clean work equipment soaked in oils, for example sanding pad or

polishing felt, with water and allow to dry. Work equipment soaked in oil

may combust spontaneously.

– Attention: Risk of fire! Avoid overheating the grinding material and the

sander. Always empty the dust container before taking a break. Swarf in

the filter bag or filter of the mobile dust extractor may self-ignite in unfavorable

conditions such as flying sparks when grinding metals. Particular danger exists

if the sward is mixed with paint, polyurethane residue or other chemical

materials and the grinding material is hot after long periods of work.

– Always use original sanding pads. Foreign pads are not suitable for the

speed of the sander and may break.

– If the power tool is dropped or falls, check for damage to the machine

and sanding pad. Remove the sanding pad for closer inspection. Repair

damaged parts before using again. Broken sanding pads and damaged

machines can cause injuries and machine instability.

3.2 Mixed dust containing metal and sanding damp surfaces

With mixed dust containing metal (such as dust resulting from paint

sanding in the automotive field) and when sanding damp surfaces,

the following measures must be observed for reasons of safety:

– Connect the machine to a suitable dust extractor.

– Regularly blow out the motor housing of the machine to remove dust

deposits.

4. Intended use

The sanders are designed for sanding wood, plastic, composite, paint/varnish,

filler and similar materials as directed. With mixed dust containing metals (such

as dust resulting from paint sanding in the automotive industry) and when

sanding damp surfaces, special safety instructions must be followed. The

sanders are not intended to be suitable for grinding bare metal.

Material containing asbestos cannot be processed.

The user is liable for improper or non-intended use.

YOUR PRODUCT

1. Technical data

Power

350W

Mains voltage

230-240V~ 50Hz

Speed

Max 10000/min

Rated Eccentricity:

Size of backing pad

150mm

Weight

2Kg

Degree of protection

IPX0

2. Noise and vibration information

Sound pressure level(LPA)

79.7dB(A)

Sound power level (LWA)

90.3dB(A)

Sound measurement uncertainty K

3dB(A)

Vibration emission ah

3.221m/s2

Vibration uncertainty K

1.5m/s2

Information:

- The declared vibration total value has been measured in accordance with a standard test

method and may be used for comparing one tool with another;

- The declared vibration total value may also be used in a preliminary assessment of

exposure.

Warning:

- The vibration emission during actual use of the power tool can differ from the declared

total value depending on the ways in which the tool is used;

-need to identify safety measures to protect the operator that are based on an estimation of

exposure in the actual conditions of use (taking account of all parts of the operating cycle

such as the times when the tool is switched off and when it is running idle in addition to the

trigger time).

Figure1

3. Commissioning

WARNING

Unauthorized voltage or frequency!

Risk of accident

The mains voltage and the frequency of the power source must correspond

with the specifications on the machine's name plate.

4. Operating instructions

4.1 The tool is intended to be operated as a hand held tool. The tool can be

used in any position. Note! The sander can develop a torque reaction when

started.

4.2 Make sure the sander is switched oﬀ. Select a suitable abrasive and

secure it to the backing pad. Make sure the abrasive is centered on the

sanding pad. For optimal performance we recommend original sanding pad

and Sanding paper.

4.3 Switch on the sander by pressing the On/Oﬀkey,

4.4 The sander can now be started by pressing the lever.

4.5 The speed can be adjusted between 4,000 and 10000 rpm by rpm+ and

rpm-. Each press increases or reduces the speed by 1,000 rpm until it reaches

the limits.

4.6 When sanding, always place the tool on the work surface before starting

the tool. Always remove the tool from the work surface before stopping it. This

will prevent gouging of the work surface due to excess speed of the abrasive.

4.7 When sanding is ﬁnished, turn oﬀthe sander by pressing the On/Off key.

The sander LED (right) is now turned oﬀ.

5. Replacing the sanding pad

Always disconnect the power before maintenance! Only use

original sanding pad!

5.1 Insert the pad wrench between the backing pad and brake seal to hold the

spindle nut.

5.2 Turn the backing pad counterclockwise to remove it.

5.3 Fit and tighten the new backing pad with washers.

5.4 Remove the pad wrench.

6. Attaching sanding accessories

The suitable sand paper and sanding cloth can be attached quickly and simply

to the sanding pad. Press the self-adhesive sanding accessory onto the

sanding pad.

In the case of a weakening adhesive effect of the sanding paper

surface, the sanding pad accessories, in particular those which are

not yet touching the work piece, may come loose from the sanding

pad and cause injuries. Replace the sanding pad!

7. Dust extraction

WARNING

Dust hazard

Dust can be hazardous to health. Always work with a dust extractor.

Always read applicable national regulations before extracting hazardous dust.

The power tool does not have its own extractor unit. At the extractor connector,

a mobile dust extractor with an extraction hose diameter of 40mm should be

connected.

Recommendation: Use an antistatic suction hose. This helps reduce the

electric charge.

Tabla de contenidos

Otros manuales de Lijadora de Feider Machines

Feider Machines

Feider Machines FPEP850LED Manual de usuario

Feider Machines

Feider Machines FBM1300 Manual de usuario

Feider Machines

Feider Machines FPGAI750 Manual de usuario

Feider Machines

Feider Machines FPB900W Manual de usuario

Feider Machines

Feider Machines FPEP1200CPC Manual de usuario

Feider Machines

Feider Machines FPG7202P Manual de usuario

Feider Machines

Feider Machines FPB1010 Manual de usuario

Feider Machines

Feider Machines FPV200 Manual de usuario

Feider Machines

Feider Machines FPG710-SH Manual de usuario

Feider Machines

Feider Machines FPB140-1 Manual de usuario

Feider Machines

Feider Machines FPV260 Manual de usuario

Feider Machines

Feider Machines FP225-KET Manual de usuario

Feider Machines

Feider Machines FPG-INDUCTION-1 Manual de usuario

Feider Machines

Feider Machines FPB1200 Manual de usuario

Feider Machines

Feider Machines SURFACER5 Manual de usuario

Feider Machines

Feider Machines FPO380 Manual de usuario

Feider Machines

Feider Machines FPG750LED Manual de usuario

Feider Machines

Feider Machines FPO350 Manual de usuario

Manuales populares de Lijadora de otras marcas

Oliver

Oliver 6305 Manual de usuario

Jet

Jet 22-44 Pro-3 Manual de servicio

Makita

Makita M9204 Manual

Makita

Makita M9204 Manual de usuario

Craftsman

Craftsman 351.215131 Manual de usuario

Clarke

Clarke Woodworker CBS1-5B Manual de instrucciones

Chicago Pneumatic

Chicago Pneumatic CP9778 Manual de usuario

Nitto Kohki

Nitto Kohki BB-20 Manual de usuario

Ferm

Ferm FEOS-135 Manual de usuario

Unior

Unior 1510 Manual de usuario

stayer

stayer ls1200 Manual de usuario

Jet

Jet JSG-96 Manual de servicio

Parkside

Parkside PDS 290 B2 Manual de usuario

Status

Status XPA Series Manual de usuario

Clarke

Clarke EZ Sand Manual de usuario

Craftsman

Craftsman 113.22521 Manual de usuario

Craftsman

Craftsman 113.225831 Manual de usuario

CLAS

CLAS OP 1429 Manual de usuario