Fast Bazooka BT6014 Manual de usuario
How to install the FAST-9999 with the FAST-BTAH
The FAST-9999 universal harness uses the patented Posi-Tap connector from Posi-Products for making
FAST secure connections to your OEM wire harness.
Posi-Tap TM Patent # 5,228,875 5,695369 5,868,589 6,692,313 Jap 2881414, Aus 708700, Tia 103534, Can 2204826
Mex 200626 Korea 477279, China Z197105562.9 & others pending
Disconnect negative battery clamp from battery.
For easiest installation remove the radio and disconnect
the harness from the back of the radio.
Connect the Posi-Tap connectors to the corresponding
wires of your radio harness. Consult your car or radio
manufacturer’s manual to get the correct color codes
for your vehicle.
Red (+) 12V Power. Turns on when ignition/accessory is on.
Blue/White Turns on remote accessories (amplifiers, etc.).
If there is no Remote Amplifier wire, you can often use the
power antenna wire.
White (+) Left Front Speaker
White/Black (-) Left Front Speaker
Gray (+) Right Front Speaker
Gray/Black (-) Right Front Speaker
Remove the top cap. Place the wire
that is going to be tapped. In the
grove of the cap as far down as it
will go.
Make sure not to cross thread the
cap when screwing it back in place.
Make sure the end with the 6 pin Molex connectors is
toward the radio. Run the BTAH harness behind radio,
dash and along the edge of the vehicle until you get
to the place you have decided to mount the tube.
Continue to thread until the cap
is tight and the wire is pierced.
Make sure to attach all 6 of the
FAST-9999 harness wires to
your OEM harness.
Plug the FAST-9999 harness into
the FAST-BTAH. Mount grounding
ring and plug the 14 pin connector
into the BASS TUBE. For more information
on placement and mounting, consult
your amplified tube instruction manual.
FAST-9999
14 pin connector
to the BAZOOKA
Ground to
chassis of
vehicle
FAST-BTAH
2
Dear Friend,
Thank you for selecting Bazooka® subwoofer speaker systems for your
stereo system Today, the Bazooka represents Bazooka Mobile Audios
continued commitment to efficiency and design An innovative
manufacturing process developed by SAS® for the Bazooka provides
consumers with state-of-the-art speaker system design
At SAS, we take pride in manufacturing the most revolutionary bass speaker
systems ever created, featuring our patented Bass Tubes® enclosure design,
and we hope you will take pride in owning them
Several years ago, we realized that efficiency was the wave of the future
in Autosound, so we made a commitment to design, manufacture, and
deliver the most efficient speaker systems possible
Today we market our patented speaker systems worldwide and the high
quality of the Bazooka brand is well respected by consumers and dealers
of all nationalities
When properly installed, Bazooka subwoofer speaker systems will give
you years of clean uninterrupted sound reproduction Therefore, I urge
you to take a few minutes of your time to review this instruction booklet
It was designed to give you a better understanding of our products and
to explain how to apply them properly
Thank you again for choosing Bazookas Our early commitment to quality
has made them the product of choice, and I am sure you will agree that
you have made the right one! Enjoy!
Sincerely,
JON C JORDAN
President
SAS/BAZOOKA
ENGLISH
3
HELPFUL HINTS BEFORE YOU BEGIN PG 4
VEHICLE PLACEMENT RECOMMENDATIONS PG 5-6
MOUNTING THE BAZOOKA PG 7-9
WIRING DIAGRAMS PG 10-11
SPECIFICATIONS PG 12&15
FEATURES PG 13-14
WIRING PG 16-20
TROUBLESHOOTING PG 21-22
WARRANTY PG 24-25
CONTENTS
ENGLISH
HELPFUL HINTSBEFORE YOU BEGIN
Please take time to read through this manual and plan out your
installation before you begin!
Locate an area in the rear of the vehicle where you would like to place
the Bazooka speaker systems The location you have selected must
meet the following requirements in order for the Bazooka to be properly
installed in the vehicle:
1) The woofer (grill end) should be facing into a corner (See
vehicle placement recommendations on pg 5-6)
2) Ideally, there should be 2 to 4 inches between the woofer and
the corner it is pointing into
3) The mounting area should be carefully checked to be sure
that the mounting screws will not damage the gas tank,
electrical wiring, fuel lines, or the spare tire during the mounting
of the strap bases
4) The strap mounting bases should be screwed securely to a
rigid surface that is part of, or anchored to, the structure of
the vehicle
4
ENGLISH
5
HATCHBACK INSTALLATION
tube size is exaggerated for emphasis
TRUCK INSTALLATION
tube size is exaggerated for emphasis
SEDAN INSTALLATION
tube size is exaggerated for emphasis
VEHICLE PLACEMENT RECOMMENDATIONS
ENGLISH
BOW RIDER/SKI BOAT
tube size is exaggerated for emphasis
Under passenger console
Under seat storage compartment
SPORT YACHT
tube size is exaggerated for emphasis
Under bed storage compartment
Under seat storage compartment
BOAT PLACEMENT RECOMMENDATIONS
6
ENGLISH
7
1. With the topside of the buckle facing up (see figure 1), lace the strap
through the mounting base as illustrated in figure 2
MOUNTING THE BAZOOKA
2. After the strap is completely laced through the mounting base, make
a loop with the strap, where it runs across the middle of the base as
illustrated in figure 3 This loop is necessary to access the two mounting
holes in the base
Figure 1
Figure 2
Figure 3
To p
Logo
should
face up
ENGLISH
8
Figure 5 3
,,
3
,,
Figure
. Move the bases so that they are spaced approximately 3 from each
end of the enclosure as illustrated in figure 5
5. Remove the Bass Tubes® enclosure without moving the mounting
bases and set it aside
6. Screw each mounting base securely in place with screws provided
as illustrated in figure 3
3. Place each mounting base under the Bass Tubes® enclosure so that
the apex at the bottom of the tube sits inside the mounting base as
in figure 4
ENGLISH
Este manual sirve para los siguientes modelos
25
Tabla de contenidos
