Fanimation CCK8002 Manual de usuario
1
CCK8002
Close-To-Ceiling Kit
INSTRUCTION SHEET
USE THESE INSTRUCTION IN CONJUNCTION WITH YOUR FANIMATION
FAN OWNERS MANUAL AND IN PLACE OF THE STEPS FOR HOW TO
HANG YOUR CEILING FAN. IF YOU NO LONGER HAVE YOUR MANUAL,
ONE CAN BE DOWNLOADED AT WWW.FANIMATION.COM.
After removing your kit from the packaging, use slight1.
pressure to push down and remove the screw trim
cover ring from the ceiling canopy assembly. (Figure 1)
Figure 1
SCREW TRIM
COVER RING
CEILING CANOPY
Figure 2
REMOVE
SCREW
LOOSEN SCREWS (2)
BUT DO NOT REMOVE
SLOTTED
REMOVE
SCREW
Separate the ceiling bracket from the ceiling canopy2.
by loosening the two canopy-to-bracket screws where
the canopy is slotted and completely remove the other
two screws where it is not slotted and set aside for
later. (Figure 2)
Twist the ceiling bracket counter-clockwise and lift out3.
of the ceiling canopy. There is another short canopy
option when it is needed to very close to ceiling.
(Figure 3)
Figure 3
CEILING CANOPY
Short Canopy
CEILING BRACKET
Safety Instructions
To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without blades.1.
All wiring and installation procedures must satisfy National Electrical Codes (ANSI/ NFPA 70-1999) and Local Codes. The ceiling fan must2.
be grounded as a precaution against possible electrical shock. Electrical installation should be made or approved by a licensed electrician.
The fan base must be securely mounted and capable of reliably supporting at least 50 lbs. Consult a qualified electrician if in doubt.3.
The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.4.
Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not have adequate electrical knowledge or5.
experience, have your fan installed by licensed electrician.
6˝ downrod 4.5˝ downrod Tall close-to-ceiling kit Short close-to-ceiling kit
2
Remove the three motor coupling screws from5.
your fan and save for next step. (Figure 5)
METAL SPACER
Route your fan wires through the ceiling canopy and6.
place ceiling canopy onto your motor. (Figure 6)
SCREW TRIM
COVER RING
CEILING
CANOPY
MOTOR
MOTOR
NOTE: MOTOR WIRES
HAVE BEEN OMITTED
FROM DIAGRAM
NOTE: MOTOR WIRES
HAVE BEEN OMITTED
FROM DIAGRAM
SCREW TRIM
COVER RING
CEILING
CANOPY
NOTE: MOTOR WIRES
HAVE BEEN OMITTED
FROM DIAGRAM
MOTOR
DOWNROD
SUPPORT
Alight the 3 big slots in the canopy to the 3 screws in7.
the motor coupler. Firmly attach the canopy cover to
the motor with the three screws removed in step 5
and steel washers from the part bag. (Figure 7)
WARNING
To avoid possible fire or shock, be sure electricity is
turned off at the main fuse box before hanging.
(Figure 8)
Figure 8
MAIN FUSE
BOX
Figure 5
Figure 6
Figure 7
On your fan’s motor, remove the two downrod support4.
set screws and nuts from the downrod support and
discard. (Figure 4)
Figure 4
NOTE: MOTOR WIRES
HAVE BEEN OMITTED
FROM DIAGRAM
DOWNROD SUPPORT
3
9. Loop the safety cable through pin hole in motor coupler
and put the cable clamp in the end of safety cable.
(Figure 10).
10. Loop the safety cable end through one of the holes in
the hanger plate up into the outlet box, then back out
the center of the plate, then connect the end with the
screw down clamp. Tighten the set screw in the clamp
. (Figure 11).
Figure 12
HOOK
OUTLET
BOX
MOUNTING
BRACKET
Figure 11
Lift your fan motor assembly and hang it from the11.
ceiling bracket hook through one of the two screw
holes in the canopy lip. Do not use the grooved slots.
(Figure 12)
Connect your fan’s wiring according to your fan’s owners12.
manual. If you have misplaced your owners manual
one can be downloaded at www.fanimation.com or
contact a licensed electrician to complete the wiring
of your fan.
Figure 10
CABLE CLAMP
CABLE CLAMP
Using the two screws and washers, securely attach8.
the ceiling bracket to the ceiling junction box, making
sure to run the supply wires through the hole in the
center of the bracket. (Figure 9)
Figure 9
MOUNTING
BRACKET
NOTE: SUPPLY WIRES
HAVE BEEN OMITTED
FROM DIAGRAM
OUTLET
BOX
WASHER
SCREW
Figure 14
Figure 15
DIMPLED
GROOVE
MOUNTING
TAB (4)
SCREW TRIM
COVER RING
Install the remaining two screws14. removed in step 2
to secure the ceiling canopy to the ceiling bracket.
(Figure14)
Push the screw cover trim ring up to conceal the15.
screws, such that the mounting tabs seat into the
dimpled grooves in the ceiling canopy midway between
the screws. (Figure 15)
.etelpmocsitikgniliec-ot-esolcruoyfonoitallatsnI16.
Reference your owners manual for any additional
assembly steps required for your Fanimation ceiling
fan.
Copyright 2011 Fanimation 2011/07 V.02
10983 Bennett Parkway
Zionsville, IN 46077
Toll Free (888) 567-2055
FAX (866) 482-5215
Outside U.S. call (317) 733-4113
Visit Our Website @ www.fanimation.com
NOTE: MOTOR WIRES
HAVE BEEN OMITTED
FROM DIAGRAM
Figure 13
MOUNTING
BRACKET
SCREW
SCREW
SLOT
SLOT
Lift the fan off the bracket hook and mount your fan by13.
sliding the ceiling canopy over the mounting bracket
with the two loosened screws going into the slots in
the canopy. Be sure all wiring is tucked into the ceiling
canopy and is not pinched. Once the canopy is flush
with your ceiling, turn clockwise to seat the screws
into the keyed portion of the slot. Tighten the screws.
(Figure 13)
Tabla de contenidos
Otros manuales de Admirador de Fanimation
Fanimation
Fanimation FP7988MB Manual de usuario
Fanimation
Fanimation Extraordinaire OF110 Series Manual de usuario
Fanimation
Fanimation Levon FP7910OB Manual de usuario
Fanimation
Fanimation The Zonix FP4640OB Manual de usuario
Fanimation
Fanimation TRIAIRE MAD8514 Series Manual de usuario
Fanimation
Fanimation AIRE DUO LP8066LBN Manual de usuario
Fanimation
Fanimation WRAP MAD8530 Manual de usuario
Fanimation
Fanimation Windpointe MW75 Series Manual de usuario
Fanimation
Fanimation Involution FP4520 Series Manual de usuario
Fanimation
Fanimation Urbanjet FP7958SS Manual de usuario
Fanimation
Fanimation Belleria FP4320 Series Manual de usuario
Fanimation
Fanimation Centaurus FP4220 Series Manual de usuario
Fanimation
Fanimation Windpointe FP7300 Manual de usuario
Fanimation
Fanimation FP6252BN Manual de usuario
Fanimation
Fanimation Huxley FP5620 Series Manual de usuario
Fanimation
Fanimation Windpointe FP7300 Manual de usuario
Fanimation
Fanimation Zonix FP4620 Series Manual de usuario
Fanimation
Fanimation The Odyn Manual de usuario
Fanimation
Fanimation Beckwith FP7964B Series Manual de usuario
Fanimation
Fanimation Islander FP320 Series Manual de usuario
